Finishing window slopes with MDF panels. How to make and mount them with your own hands? Do-it-yourself MDF door slopes: what you need to know ?! Do-it-yourself mdf doorway

One of the complex and painstaking processes is the installation of a door, which requires certain knowledge. At the same time, MDF door slopes are one of the main parts of the door space. Slopes are divided into internal and external. Their installation is carried out at the last stage of door installation. They perform two functions: practical in terms of insulation, as well as aesthetic. They can be installed in a different way, but it is worth paying attention that the main material of the product will directly depend quality characteristics and securing the door.

There are basic rules that you need to know and consider when installing doors:

• For free opening of the door, the slopes must be installed on the lower level of the frame (20 mm).
• The distance between the slopes should be different.
• To ensure the correct installation of the box, you need to carefully measure.

Choice of finishing method

It is possible to finish the doors in any way. The standard option is to attach the finished slope to the door frame. Thus, you do not spend time on the main work of making a slope.

There are other ways, for example, finishing with drywall or plaster. They are also in demand, but the work is more difficult for a person who does not have special building skills.

Choose the right way finishing is recommended taking into account the type of door frame. In the event that the slope will be performed for interior door, no insulation is required. The ideal option for decoration are decorative materials.

But the front doors require careful work. MDF would be ideal. It is a wood fiber board. It is in great demand in the construction market for this stage of work. MDF is not affected by drops temperature regime, and also does not allow the appearance of dampness. It is recommended to choose the color of the slopes to match the color of the door. The ideal type of quality finish can be a combination of materials, for example, plaster and MDF.

Tools and materials

Before starting work on installing slopes, it is worth knowing what tools and materials will be needed. We will look at how to make do-it-yourself MDF door slopes in a combined way.

To carry out the work you will need:

• Sealing foam.
• Dowels for fixing MDF.
• Putty, sand, cement, primer.
• Mortar.
• Liquid Nails.
• Building profile.

Manufacturing process

This way of working requires careful attention. Therefore, it is best to follow each step of the instructions.

When the door is already installed, you will see how cracks have formed along the edge of the door. Between the door frame and the wall, they must be repaired, for this it is worth using mounting foam.

It will take some time for the foam to completely harden. After that, its remains must be cut off and the irregularities removed.

Next, proceed to the surface treatment, where the joints will be installed. Primer is applied first. It will help strengthen both materials and give them protective properties. To ensure the evenness of the opening, it is necessary to carry out plastering. Using a building profile, you will be able to apply the plaster evenly. The corner to the corner of the slope should be fixed with dowels.

After that, the plastering process begins. For getting required material you need to mix cement, sand and lime mortar. There is an alternative option - this is a facade putty, it can fully replace the mixture for plastering.

Putty should be applied in a thick even layer. Excess mortar can be removed with a wooden rail. To strengthen the corners of the opening, it is worth using a perforated profile. It must be tightly laid in a layer of not dried plaster. After that, a layer of plaster is applied and thereby the irregularities on the surface are removed. At the same time, it is worth paying attention to the fact that you need to wait for each layer to dry before applying subsequent layers.

After the procedure for applying putty is completed, it is worth proceeding directly to the installation of MDF panels.

• Firstly, it is recommended to start work from the base for the slope. Lime-cement mortar is laid on the surface and allowed to dry well. Then a layer of primer is applied.
• Secondly, MDF will need to be cut. This must be done to form three separate parts for the future product - one top and two side.
• Thirdly, you need to apply a certain amount of adhesive mass to the top of the opening. Then press the part and hold it until the glue hardens completely. The same procedure is carried out for the other part of the slope. In order to tightly fix the MDF panels, builders recommend using a spacer, which is laid at floor level.
• Fourthly, the space that has formed can be sheathed using a small piece of plastic. You can fix it in any convenient way.
• Fifth, you need to measure each corner of the doorway. In order to avoid the appearance of cracks, before mounting, you will need to attach a part of the material and check the tightness of the connection. At the corners it is worth attaching the panel details. Please note that the corners should be half of the total opening angle.
• Sixthly, decoration should be carried out in the same way and with the same material from which the door is made.

Door slopes from MDF give the interior a completely finished look. But their installation requires compliance with certain technological rules that allow you to achieve the necessary reliability. The fact is that any violations can lead to undesirable consequences. Although all the work is easily done by hand with a minimum set of tools.

- This is a simple procedure that requires only a certain accuracy and compliance with some nuances. Can be used in work different materials, but MDF panels are considered the most successful. Their popularity is due to numerous advantages:

1. Availability. Indeed, now there is a wide variety of these products that are affordable. You can buy all the necessary accessories for them.
2. Ease of installation. Naturally, if there is no experience, then any Finishing work may seem complicated. But it is worth a little practice and understand the essence - the work will seem easy enough.
3. Great look. There is a certain rule, which is that all elements must be combined with each other. Therefore, the slopes on the front door must be made of suitable products. MDF - will great solution in such situation.
4. Additional sound and heat insulation. This is an important point that many initially do not take into account.
5. Safety. The panels are completely eco-friendly.

MDF panels allow you to create a spectacular decorative coating and insulate slopes

We must not forget that there are no completely ideal materials. Therefore, the disadvantages should also be taken into account:

1. Medium resistance to damage. Such a product perfectly withstands various impacts due to its high density, but is very unstable to scratches, as well as to other similar influences.
2. MDF is a poor option for rooms that have high humidity.
3. Sometimes it is difficult to select additional elements. The fact is that overhead MDF corners, which have a limited decorative range, can be used for decoration. Therefore, you should think over the overall design in advance.

On a note! Many mistakenly confuse the finish doorways MDF and installation of extensions on door frames. These are completely different procedures. It should be borne in mind that extensions are great for narrow (up to 11-12 cm) and straight openings that are found in interior structures.

Finishing technology

Installation is divided into several stages, each of which depends on general condition opening. It is assumed that all work will be carried out thoroughly.

Preparation

It all starts with preparatory activities. This is especially important for front doors. The fact is that they are a link with the outer space. Accordingly, this leads to the fact that cold can penetrate through the existing cracks and cracks and heat can escape.

The following manipulations are performed:

• The surface is completely cleared of everything superfluous. It is necessary to foresee the protection of the door leaf and adjacent areas (floor, walls) from damage. They are covered with plastic wrap and cardboard.
• The coating should be carefully examined. If it has traces of destruction, then it is removed completely, to the ground.

On a note! The front door can be full of surprises. The fact is that a lot of wires are passed through the jamb. This is an electric (input) cable, twisted pair to the Internet and more. Therefore, extreme caution should be exercised.

• If work is carried out in connection with the installation new door, then a well-cured polyurethane foam is cut off.
• A layer of plaster or putty is applied. It should completely cover all cracks and chips. After drying, everything is covered with a primer, and the joints are coated with sealant.
• A layer of thermal insulation is laid. Exist various options of this product, which are selected based on the thickness of the assembly seam. The fact is that the thicker it is, the more the layer needs to be built up in order to install the MDF parts.

Stages of preparing the slope for the installation of MDF panels

slope finishing front door MDF panels is a procedure on which the overall microclimate inside a house or apartment depends. If you do preparatory work poor quality, for example, to leave gaps and unsealed joints, then there is a high probability of a draft.

Detailing

Detailing is done by hand quite simply. It is necessary to remove all dimensions from the opening and transfer them to a piece of paper. Based on the available data, a diagram of each element is drawn up. Important nuances are taken into account:

1. The presence of a threshold.
2. The sequence of fragments. Namely, the thickness of the horizontal element is subtracted from the two sidewalls.
3. The overall width of the opening, as well as various angles tilt.

It is necessary to carefully measure the opening, taking into account all the features of the door slope

Used for cutting electric jigsaw, which can be replaced hand saw on wood with fine teeth.

Installation

Facing the surface of MDF panels occurs in two ways. The width of the opening also plays an important role. If the strips are not large enough, then they have to be joined. Of course, this is best avoided. In this case, the installation is carried out exclusively on the crate. If it is possible to install solid parts, then an adhesive option can be used.

On a note! MDF has a sheet variation. Such products are great for any work, but have limitations on the decorative component.

In the presence of a wide door slope, which requires docking of panels, MDF installation produced only by the method of erecting a frame

Frame installation

This method involves the use wooden beam, which will serve as a support for the parts. There are tips where it is proposed to use a metal profile. This option is great if the walls are sheathed with a common frame.

The technology is:

• Rails are installed horizontally. Between them it is advisable to maintain intervals of 30-45 cm.
• They are attached to dowels.
• The voids are being filled mounting foam or a heater.
• Prepared parts are tried on in size. Next comes the turn of their fixation. To do this, you can use self-tapping screws. They are recessed into pre-prepared holes, which are smeared or closed with special overlays.

You can use other technology. In this case, the foam will act as glue. It is poured after installing the parts in the existing voids. Care must be taken, the composition should not be much.

Mounting foam tends to expand, therefore, when filling voids, it is important not to overdo it with the amount of material poured

Adhesive method

Slopes made of MDF on the door can be mounted without using a frame. This option provides that the parts will be laid directly on the surface. For this, glue is used. This method is perfect when the thickness of the mounting seam is minimal.

The general procedure is as follows:

• Good initial preparation is essential. It should be borne in mind that it is not always possible to use a heater in this situation. Therefore, all cracks must be smeared, and the areas covered with a layer of putty. Everything is treated with a primer.
• Glue is applied to the wrong side of the parts that are pressed against the surface. After waiting a little, they are torn off. You should wait for some time, which is necessary for the adhesive composition to gain its functions.
• Further, all elements are installed in their places. Existing joints are covered or covered with overlays.

Now all that's left is to finish the exterior. For this, facing with platbands or simple leveling with putty is excellent.

After installing the entrance doors, the joy of replacing can be overshadowed by a bare wall with attachment points, which still needs further finishing. by the most the best option is the sealing of the slopes of the input MDF doors panels that are affordable and take less time than plaster or other methods. If you have a hacksaw, jigsaw, Sander and a can of foam, then you can do the work yourself

Benefits of sealing MDF slopes

Installation of slopes from MDF is affordable for most buyers, and the color scheme allows you to choose the design that matches the door leaf and the style in the hallway, so most of those who installed new doors prefer finishing the opening with this material. More MDF extensions are distinguished by the following advantages:

• the material isolates the opening from noise and cold;
• tolerates moderate impacts and is resistant to damage;
• the decorative layer contains a pattern imitating natural wood that looks very rich and gives comfort in the hallway;
• easy installation that does not require a hammer drill or the ability to handle a drill.

Preparation before finishing slopes

In order for the sealing of the slopes to be of high quality, it is important to properly process the walls that remain under them, otherwise a fungus may develop there or it will blow cold from there. After installation, a lot of fine dust and debris remains in the opening, so you need to thoroughly clean it. To prevent the formation of dampness and mold, it is recommended to treat the wall with antiseptic impregnation. Next, the surface is primed.

If after installation there are small gaps that the installers missed, then they must be sealed with foam from a spray can so that cold air does not get on the extensions from the inside. When the material hardens, it will need to be cut off at the end, so that when finishing the slopes of the front door with MDF panels, it does not rest against the foam, which will not allow the wooden lining to fit snugly in the box.

Preparation includes cutting panels the right sizes. Usually use a material with a thickness of 8-12 mm. It can be placed vertically or horizontally. The first option allows you to quickly close a large area, so they stop on it more often. An electric jigsaw is used for cutting, but it is important to ensure an absolutely even cut line. If there are no such skills, then it is better to order a cut in a carpentry workshop. The width of the panels is preferably such as to completely cover the distance from the box to the corner of the wall. The second set is prepared for wrapping at an angle (platband) and its width is considered to be a standard of 7 cm.

Stages of sealing slopes with MDF panels

When everything is ready, you can proceed with the installation. The work is carried out in the following stages:

1. It all starts at the top. Preliminary foam patches are applied to the wall at the top of the opening. Their diameter is 5-8 cm, and the height depends on the distance of the wall from the beginning of the dimensions of the box. Ideally, you need to make a slope of the front door from MDF so that the panel is flush with the box or even a little lower.
2. The cut-out overlay is attached to the place at the desired height. There will be a gap between it and the wall. It is tied up with masking tape and then the position is adjusted according to the level. From below, the bar is supported by a T-shaped wooden spacer.
3. Now you can bring the nose of the gun inside and apply large quantity foam for better fixation, but you must act carefully so as not to squeeze the material out.
4. By the same principle, side panels are installed on tubercles with foam, only they will need to be burst with pieces of timber tied to the box with adhesive tape to eliminate the curved shape of the MDF.

After closing inner wall opening you need to create a beautiful transition to the outside. For this, a second set of cut strips 7 cm wide is used. But before fixing, it will be necessary to cut the end of the panel at 45 degrees in order to get the correct joint with the upper jumper. For such trimming, measure 7 cm in length from the edge and draw a solid line to the corner, along which the cut is made. This is done on the right and left panels in mirror image. The cut edge is sanded for a neat look, but should not be too close to the outer surface, so as not to remove the decorative layer.

The panels are mounted on mounting foam and fixed with masking tape to the wall and door leaf. At the bottom, their length is carried out to the plinth, if it already exists, or to the floor itself, and the plinth is already spreading from the lining. The installation of MDF slopes on the front door ends with a sticker of a plastic corner with a 15 mm shelf on the corner of the wall around the perimeter, which is allowed only after the foam holding the main structure has dried and the tape has been removed. The color of the element closing the joint is selected identical to MDF, which will look complete and beautiful.

Online store "The Right Choice" offers not only to correctly install metal door, but also to close the slopes with MDF panels, which will completely save the owners from the final finishing work. Installation of extensions starts from 800 rubles. and a wide range of panel colors and thicknesses are available. It is possible to install the whole portal. It is convenient to find out the deadlines and finishing options through the feedback.

Installing a new door is a joyful event for every owner. However, the work is not limited to the installation of the box and the canvas alone - in the end, it is necessary to arrange the slopes so that the design looks beautiful and organic.

To carry out this event, of course, you can invite a specialist. However, does it make sense to overpay for the services of a third-party master, if such a simple job can be done on your own?

For the design of slopes (- article), materials such as plaster, polyvinyl chloride-based panels, drywall and MDF panels are most often used. Study the presented guides, choose the design option that suits your case and get to work.

First step. Seal with mounting foam all the gaps between the base and the door frame. Let the foam dry and carefully cut off the excess foam with a sharp knife. Carefully sand down any unevenness with sandpaper.

Second step. Proceed to surface treatment for future trim elements. Apply a coat of primer to ensure better adhesion of the plaster to the surface.

The primer usually has to be applied in several layers. Focus on the situation - as a result, you need to get a perfectly flat and smooth surface. Start applying a new layer of primer only after the previous leveling layer has completely dried.

Third step. Start plastering. Buy ready-made facade plaster or prepare a mortar with your own hands from a lime mixture, fine clean sand and cement.

Start plastering from the top door slope. Apply the mixture in a thick layer. Level and remove excess putty with a wooden slat.

To further strengthen the outer corners, mount a perforated corner profile. It must be pressed a little into the still damp plaster mixture.

Let the top coat dry completely and apply the final coat of plaster mix. It should be thinner. The main task of this layer is to level small irregularities. Wait for the final plaster to dry completely. Simple door slopes are ready.

Plastering is the most budgetary option for decorating slopes. Whether to give preference to this method or choose some other way of finishing - each owner has the right to decide independently.

Video - Door slopes

Beautiful and inexpensive slopes can be made from plastic panels. First, the frame is prepared, and then the finishing is performed directly.

frame

For the frame, prepare a beam with a section of 2x4 cm. Plastic panels will be attached to the frame.

Saw the timber into blanks according to the size of future slopes. Fix 4 perpendicular strips on each wall part of the doorway. Attach 3 strips to the top. Use nails to fix the elements.

Side elements

Finishing panels should be slightly wider than the surfaces decorated with them. Finishing elements will need to be bent so that they beautifully “beat” the corners.

From the end, the plastic panels have a hollow structure. Voids of the correct form are present along the length of the elements. To give the panel the desired shape, make appropriate cuts along the voids mentioned. An ordinary clerical knife will help you with this.

If desired plastic panels you can even finish the columns, so there will definitely not be any problems with finishing the corners of the slopes. The joints will be barely noticeable.

Make cuts exclusively on the reverse side of the trim elements.

Attach the cut modules to the frame. For fixing, you can use self-tapping screws or small nails. Fix the bent elements to the wall surface. Work in this order:

• define the border of the trim element;
• make five holes in the wall so that in the future they are covered by the edge of the panel;
• hammer wooden plugs into the prepared recesses;
• screw the panel to the wooden plugs with self-tapping screws (nail it).
• Install all panels according to this algorithm.

Beautiful slopes for the door can be made from drywall.

Video - Installation of a drywall slope on the front doors, part 1

Video - Installation of a drywall slope on the front doors, part 2

First step. Drill holes around the entire perimeter of the opening at a distance of about 200 mm. Hammer the dowels into the holes and screw the screws into the dowels, slightly without twisting the end.

Second step. Determine the appropriate dimensions for the starting rail. To do this, you need to measure three sides of the opening. Cut the guide to your measurements.

You can make the upper guide along the width of the opening, since in the future the side sheets will rest against the upper slope. You can make the side guides a little shorter.

Third step. Screw the starter rail to the wall with self-tapping screws. The long side, at the same time, should be placed outside the door slope, and the short one - inside.

Fourth step. Mark the strips on the drywall sheet required size. Cut out the drywall according to the markup.

It is very important to observe the cutting technology. Otherwise, the cut edges will be ugly.

For cutting, attach some long, even object to the marking line, for example, a piece of a mounting profile. cut through upper layer paper. Gently tapping the cut strip from the back of the sheet, break through the plaster, and then cut through the second paper layer.

Fifth step. Prepare the glue mixture. Follow the instructions specific to your glue.

Sixth step. Apply a homogeneous adhesive mass on reverse side drywall strips. Also glue must be smeared with pre-mounted dowels.

Seventh step. Proceed directly to the finish. Bring the edge of the strip into the starting guide. Align the trim element and then press it to the base. Fasten the side slopes in the same way. Remove excess glue immediately, otherwise in the future it will lead to deformation of the drywall.

Slopes need to be supported with spacers while the glue dries.

You can fill the gaps between the base and drywall with the removed excess glue.

Give the slopes 12-24 hours to dry and you can start finishing: puttying, painting or other finish of your choice.

Such slopes will serve for many years without any complaints.

Beautiful door slopes can be made from MDF.

First step. Prepare the basis for future door slopes. To do this, treat the base with a simple lime-cement mixture. Let the mixture dry and apply a primer over it.

Second step. Cut the MDF into three slopes of the required dimensions. Before you start cutting, carefully measure the angles of joining the sides of the opening. Next, you need to cut the ends of the trim elements in accordance with the measured angles.

Before proceeding with the installation of panels, make sure that the joints are correct. To do this, attach the connected elements to each other. Try not to have any gaps - they will spoil the appearance of the finish.

Third step. Apply the desired amount of adhesive mixture to the top of the doorway. Press the appropriate trim element to the adhesive and support it until the adhesive dries completely. Fix the side elements in the same way.

For the best possible fixation of the elements, place spacers between them.

Hide the gaps between the base and the fixed slopes with plastic corners. To fix the corners, use liquid nails or other suitable glue.

Try to choose panels for the manufacture of slopes, the appearance of which would be as close as possible to the appearance of the door leaf. Such a finish will look as holistic and beautiful as possible.

Thus, a wide variety of materials can be used to equip door slopes. Select suitable option, follow the provisions of the instructions given, and you will be able to cope with the tasks set as well as any specialist.

Successful work!

Video - Do-it-yourself door slopes

In order to install the door yourself, you need to have some experience and knowledge in this matter. Slopes from MDF input doors in this case are part of the space, and quite important. Installation of slopes, which are often made of MDF, takes place on final stage door installation.

Function MDF slopes In this case, it consists, firstly, in improving appearance structures, and secondly, in the insulation of the room. The installation method may be different, however, it is necessary to take into account the material from which the door leaf itself is made, since the protective properties of the door and other equally important characteristics depend on this. When installing a door, you must consider the following rules:

• to ensure the free opening of the door, the installation of slopes must be carried out at the bottom of the box (20 mm);
• slopes on the front door must be placed at different distances;
• Correct measurements must be taken to properly mount the door.

Facing can be done in various ways. The standard method includes attaching a ready-made slope directly to the box itself. In this case, there is a great time saving, since it is not required to make the slopes for the entrance doors themselves.

There is a finishing option using drywall or plaster. This method is considered no less popular, however, not everyone will be able to produce such a finish, since this requires some knowledge in the construction field.

In order to determine the method, you need to know the type installed box. If door slopes are installed on interior design, insulation in this case is not required. Here, the best option would be facing with decorative materials.

As for the front doors, they require more careful and careful work. Here, the best option would be MDF panels (wood fiber boards). Their popularity is quite high, since this material is not affected by temperature and dampness. The color of the panels in this case is selected in accordance with the color of the door itself. High-quality finishes include the combined use of MDF with plaster.

Tools and materials for work

Before starting work, you need to make sure that you have all the tools. To install the slopes of the front door, using the combined method, you will need:

• foam, with which joints are sealed;
• primer, cement, putty, sand;
• dowel;
• mortar;
• profile used in construction;
• liquid Nails.

Manufacturing instructions

This method requires a special attitude, so you must follow all the instructions exactly. It would be useful to watch a video on the topic: "How to make slopes." As soon as the installation of the door is carried out, the appearance of cracks can be observed along the edges. In this case, in order to close up such gaps between the wall and the box, a special foam (mounting) is used. After using it, you need to wait some time for it to harden, cut off the excess and trim the surface.

This is followed by surface treatment in those places where the joints will be located. The first step is to apply a primer, which will strengthen the material and improve its protective properties. Surface evenness can be ensured by plastering using a profile. As for the corners, their fastening to the corner is carried out with the help of dowels.

You can start plastering, but first you need to prepare the appropriate solution. It is prepared simply, it is enough to mix sand, cement and lime mortar. In some cases, it can be replaced with putty, which is used for facade cladding. It must be applied in an even, fairly thick layer, removing excess with a wooden lath.

The corners are reinforced with a perforated profile laid in a layer of plaster. The next layer should be applied after the previous one has dried. Once the puttying process has been completed, the MDF panels can be installed. Finishing the slopes of the front door with MDF panels with your own hands includes the following steps:

1. Before starting work, it is necessary to prepare the basis for the slopes for the front door. The appropriate solution is laid on the surface, after which it needs to dry. A primer layer is applied.
2. Cutting MDF. It is done to obtain three separate parts for the upper part of the structure and the side ones.
3. Glue is applied to the upper part of the opening and the MDF panel is pressed. It must be pressed and held until the mass dries. Other parts of the slope are made in the same way. For a tighter fixation, on the recommendation of the builders, spacers can be used.
4. The space formed during the work is sheathed with plastic of a small size.
5. The next step is to measure the opening angles. To prevent gaps from appearing, before mounting, it is necessary to attach the material and see how tightly it fits. Then we attach the panel details to the corners. It should be borne in mind that the corners account for half the value of the opening angle.
6. The final step is decoration. For this, the same material from which the door itself is made is used.

Thus, observing all the nuances and following the instructions, it will not be difficult to do quality work, and if you still have any questions, you can watch the corresponding video.