Homemade drill holder for a mini drill. It is not difficult to make a drilling machine from a drill with your own hands. Do-it-yourself power tool accessories

A drill is usually used to create holes in the wall. But at the same time there is no guarantee that it will turn out even. Therefore, to eliminate this shortcoming, one has to use accessories in the form of a guide for a drill. Using it, you can do this work with less physical effort. However, difficulties arise when drilling a hole at an angle of 90 degrees, and during certain work, the angle of the created hole often must be 45 degrees. In this case, it is necessary to carry out appropriate preparation of the working tool in order to fulfill this requirement.

A rather difficult task is to create a hole in structures made of too hard materials. This leads to slippage during the operation of the drill, which creates a danger to the worker and people around him, who may be injured. You can avoid such unpleasant consequences and at the same time simplify such a process with the help of such a device as guides for a drill. If necessary they can be made by yourself, and the presence of a large number of options allows you to choose the most preferable among them.

The simplest guide nozzle for a do-it-yourself drill

Considering this version of the nozzle, one should take into account the fact that it will not be necessary to spend any money on the implementation of the idea. But at the same time there will be no special difficulties in manufacturing drill guide. But at the same time, the created device can serve for a short time.

It is important to note that it should not be considered as a complete complement to the tool. In the event that you have to create a hole at a considerable distance from the workshop and there are no other alternative devices, then it is with the help of such a nozzle that you can most effectively solve the problem. In addition, it will bring significant benefits to those home craftsmen who do not work with a drill so often.

materials

For the manufacture of the guide, it is necessary to prepare the following materials and tools:

plastic bottle;
plastic cover;
drill;
stationery knife;
felt-tip pen;
universal glue;
annular drill;
sandpaper;
drill.

Manufacturing process

First you need to perform certain manipulations with the drilling tool. To do this, twist the nut and the fixing drill from the drill. Then note its diameter plastic bottle as close to the neck as possible. Then transfer the circle corresponding to this diameter using a felt-tip pen. The end result should be a complete circle.

This template, which must be cut out later, should also be marked on the bottle cap, and care should be taken that its width is sufficient for this.

The next step is to cut the bottle or jar. The choice of the trimmed design should be approached very carefully, since this will further affect the depth of the holes created using a guide.

Particular attention should be paid to work safety. To do this, it is recommended to sand the edges of the jar to make them even and smooth.

The holes that were previously applied to the bottle and its cap should be cut exactly along the intended line using a clerical knife. Processing should be carried out with the edges of the cuts, which must be thoroughly sanded. Then take the lid and place it face down in the jar, acting on it with physical force to ensure the tightest possible fit. It is in this area that it is glued.

The strongest connection can be achieved if, after applying the adhesive, a strong compression is provided, which must be maintained until the adhesive dries. Considering that doing this work manually is fraught with certain difficulties, it will be useful to fasten a few thin elastic bands on top, thanks to which you can maintain the required pressure.

After waiting for the glue to dry, the drill attachment can be used for its intended purpose. A drill is inserted into it, after which, using a plastic nut, it is fixed on the tool and drilling of the hole begins. Although it does not have the ability to select the depth, this the problem can be solved by making several similar nozzles and use as needed the most appropriate.

In a situation where you have to drill a hole with a rather massive drill, there are certain difficulties associated with the need to provide the hole with an angle of 90 degrees and exclude its oval shape. If the master’s arsenal does not include devices and tools with which to make a guide, this problem can be solved by using improvised materials.

Even before creating a hole, you need to take care of the availability necessary materials: for this you can take a square bar made of wood or other material.

The bar must be positioned against the wall in such a way that it closely adjoins the hole that needs to be processed. Moreover, the edge of the drill should touch it, so that the drilling process will go smoothly.

To improve the convenience and accuracy of drilling, two different bars can be placed at right angles, while the drill is inserted into the inner corner between them. It's a good idea to place the bars so that they form a "T" together. Thanks to this, it will be possible to give it the necessary position and the owner will be able to protect his hands from injury.

A drill, used in combination with a guide, is able to play the role of a small, simple drilling machine, with which you can perform various operations that require precise dimensions.

Important nuances

Having decided to create such a device with your own hands, you need to take into account such important points:

moving parts must be tightened as tightly as possible. For effective work, a do-it-yourself nozzle for a drill, it should be possible to select a suitable reach and stroke. Moreover, if the guide post has a rather significant weight, then this only simplifies the process of creating holes.
In some cases rack can be used in combination with a vise, thanks to which it is possible to fix the workpiece. In this case, such a design easily turns into a full-fledged drilling machine. Moreover, it is not necessary to purchase such a vice in order to expand the functionality of the equipment. If you have enough experience, you can also make them yourself.

Conclusion

Drilling work is one of the most frequently performed during the manufacture of various structures. And House master most often solves this problem with a household drill. However, for the most part, the hole created is the same exact dimensions. And this can create certain difficulties when using it for its intended purpose.

You can get out of this difficult situation with the help of guides for a drill, which you can make yourself. Such an idea seems quite attractive for the reason that any owner can make such a nozzle, given that any means at hand can be used for this. However, having realized all the attractiveness of the guide, it must be remembered that it will not be able to become a full-fledged fixture for a drilling tool, therefore, resort to the help of this nozzle should only be in emergency situations. Otherwise, the drill guide will fail pretty soon.

A screwdriver or drill is available in every home. But how often do you use them for their intended purpose? But this is, first of all, a powerful motor in a safe case and with a comfortable handle. Therefore, it is enough to add accessories for a drill, and the functionality of the tool will be expanded.

There is a whole industry for the production of such "gadgets", their number is in the dozens. Consider the most popular of them.

Drill holder - what is it

The drill can be used as grinder, grinder, cutter In all cases, it is necessary to fix the tool on the workbench. Given the complex shape of the body, simply pulling the drill to the table will not work, the spindle axis will not be parallel to the working surface. The manufacturer has provided a special groove - a neck on the body.

Its main purpose is to mount the second handle. And since the neck of the drill is a structural structural element, it can be used as an attachment point.

The holder for the drill is a clamp (as a base), a collar is fixed on it, in which the neck is clamped.

fixed clamp - the tool is fixed and parallel to the table
swivel clamp allows you to rotate the tool around a vertical axis
holder with two degrees of freedom adjusts both horizontal and vertical angle of position.

Important! The typical diameter of the clamp is designed for a neck of 43-46 mm. Before buying a fixture, check the dimensions of your tool.

There are also unique devices that have an unlimited degree of freedom. However, the cost of such devices may exceed the price of the tool itself.

A simple holder can be made independently. Usually this is a horizontal stop with two attachment points.

The main (power) collar for clamping the neck, and the rear bracket for making the drill axis horizontal.

Mixer - nozzle for mixing paints

Another popular accessory is the mixer attachment for the drill. This is not about food processors. Although, by attaching a manual whisk or pepper mill to the cartridge, you can mechanize the tedious process.

With the help of various nozzles, building mixtures and technical compositions are mixed. This is a simple device, however, it will not work to make it yourself.

When choosing a mixer nozzle, you should consider the power of the drill. During stirring, a lot of force is applied to the axis of the mixer. The motor is designed for a certain torque, if the load increases, the windings may burn out.

Drilling machine from a hand drill

Pretty hard to keep hand tool strictly vertical. Therefore, when drilling holes in thick workpieces, it is more practical to use drilling machine. At home (especially in an apartment), it is inconvenient to maintain such a mechanism. But you can use another device - a rack for hand drill.

You get a real drilling machine that can be disassembled after use. However, this device costs money. Despite the complexity of the design, a homemade drill stand can be made from improvised materials.

by the most simple option is the vertical guide. The device ensures the straightness of the movement of the drill, while there is no feed mechanism - you just work with your hands.

For manufacturing, you will need 10mm thick plywood and guide slides for cabinet furniture. Non-separable slides are used, with two rows of bearings.

The stand is made up of two parts.

The base (bed) must be heavy and stable. It is assembled in the form of a box fastened with screws or screws. Slides are vertically fixed on the bed, which are set in a strict vertical according to the building level. A handle is attached to the side of the frame to hold it while drilling. If the bed will be fixed on a workbench, an additional handle is not required.
The carriage is attached to the moving parts of the slide and serves to temporarily fix the electric drill. The holding mechanism can be any, the main thing is to ensure a tight fit of the tool without play during operation. During installation, it is necessary to ensure a vertical stroke along the axis of the drill

How it works

Having fixed the workpiece, you habitually take the drill by the handle and feed it to the place of drilling. The stand will ensure the verticality of drilling, and will allow you to control the force of pressure on the drill.

Homemade drill stand with feed mechanism

Drilling on the machine is more convenient when you hold the part with one hand and move the feed lever with the other. This is how all drilling machines work. You can create such a device with your own hands.

For manufacturing you will need:

water pipes of different diameters
steel strips 3-4 mm thick
tensile spring (door fit)
fasteners
access to electricity

Looking at the design, you will understand how you can replace the listed materials.

The most important part is the clamp to hold the drill. It is made of a two-inch plumbing nut, on which lugs are welded for a tightening bolt. In such a mechanism, a drill with a neck of 46 mm is perfectly fixed.

Thrust with a return spring can be hidden in a thin-walled glass. Geometry is not needed here, there is no need to achieve strict verticality.

Guide bushings - brass (you can use fluoroplastic, which material will be at hand). With a little lubrication, the sliding will be smooth, without wedging.

The lever is made according to the simplest design - a groove in which the axis moves freely. The play is regulated by a self-locking nut. The bending of the lever is carried out depending on the size of the drill itself.

The design is simple and reliable. Such a machine can be made in one day off (if you have a tool, of course).

Angle nozzle on a drill or what is it

Often you have to drill holes or turn screws in hard-to-reach places ah, with limited space. The drill does not fit there, but there are devices akin to a pistol shooting from around a corner.

The angle attachment is a pair of bevel gears that transmit torque at an angle of up to 90° with virtually no loss. With obvious advantages, the device has a serious drawback - there is a high risk of breaking the drill. Therefore, it is preferable to install a nozzle with fixation on the neck of the drill.

And we move on to exotic devices.

Pen holder for drill

Can a perforator be used to pluck a bird? Probably not. But a hand drill - easily.

The nozzle is a crown (like those used for milling recesses in the walls for sockets). Rubber fingers are inserted into the cylinder. It is these rubber bands that grab the feather and clean the carcass. Similar devices are commercially available.

However, most poultry farmers make them with their own hands. Only the main elements are bought - rubber fingers.

And the structure itself is easily made from a piece sewer pipe and steel pin. Birds are plucked at low speeds, so special centering is not required. The main thing is the reliability of the connection of clamping plugs.

In this video, we will show a few more options for existing homemade nozzles on a drill

obinstrumente.ru

It is not difficult to make a drilling machine from a drill with your own hands, the main thing is to decide on its appearance.

Everyone who uses a hand drill knows how difficult it is to keep a strict vertical with your hands. When drilling workpieces of large thickness, there is a risk of breaking the drill. Every time there is a desire to guide the tool along the guide, but there is no such possibility.

The second common task is to drill many holes of the same type in one workpiece. Holding a drill in your hands, doing such work is long and inconvenient. Drilling machines have been used in metalwork workshops since ancient times. different power. But their cost for home purchase is too high.

In addition, the home master does not perform drilling on an industrial scale. Therefore, such a purchase will never pay off. There are factory-made vertical drilling fixtures that can turn a hand drill into a full-fledged drilling machine. Many of them are equipped with coordinate plates and movable vise.

Stand vertical for drilling holes with a drill

This is a really convenient purchase, but the cost of such a machine is comparable to the cost of a drill. Therefore, home craftsmen often make a homemade drilling machine. The main advantages of the design are low cost and the ability to create a fixture that is perfectly compatible with your hand drill. If there is an unnecessary photographic enlarger, microscope or other mechanism with a vertical feed of the working unit in the house (barn, garage), the task is simplified.

Homemade rack from an old microscope

It remains only to adapt the drill to the product. If there is no such bonus, the stand is made from scratch.

How to make a machine out of a drill using improvised materials

What should the guide stand for a hand drill consist of:

In practice, your drill does not always have such a landing ring. In this case, the tool is fastened with clamps to the body. With this method, it is important to achieve good centering of the axis of rotation, and, of course, its ideal verticality.

Homemade option machine from mounting plates

IMPORTANT! The axis of rotation of the drill is always vertical. For angled drilling, reorient the workpiece.

There are more original designs for mounting power tools. Appearance doesn't matter. The main thing is reliability and ease of use.

Drill mount made of plywood

Drill switch.

This structural element is important because, in addition to convenience, it ensures the safety of work. If you plan to leave the power tool in the machine forever, you can dismantle the button and install a stationary switch on the machine body instead. If the drill will be periodically used as a hand tool, the best way to resolve the issue would be to install the socket and the power button in convenient location fixtures.

Workplace lighting lamp.

There are many options for creativity. The main thing is that it is really necessary. Let us dwell separately on the method of fixing the workpiece. A machine with a vice is undoubtedly more convenient, but it is imperative to provide for the possibility of dismantling them. When processing large parts, the surface of the bed must be flat.

Consider the most successful models of homemade machines

These options show polar levels of technology. From primitive, collected from waste, to relatively technologically advanced, using ready-made components.

A structure assembled literally from past materials

Drawings for assembly are not required, all parts are adjusted in the course of work. For the manufacture of the bed, a chipboard sheet 50x50 cm is used. We use wooden round timber as a support for the rack. It will also give stability to the structure, lowering the center of gravity. The movement mechanism is made from a guide for furniture drawers. Of course, none of these things are bought in a store, but are removed from the trash in a barn or garage.

Furniture rail can be used to make a home machine

A bar rack is screwed to a round timber, a guide is attached to the opposite side.

Fasten the guide to the wooden rack

The drill bracket is made from a small board, in which a suitable hole is drilled with a crown. The only part that is made using welding is a corner with a jib for rigidity, with which the bracket is attached to the rail.

We make a mount for a drill from a piece of board or plywood

We assemble the lifting mechanism and check the verticality of the stroke and freedom of movement. The lift lever is made from a suitable thin bar. A metal corner is installed on the round timber, the lever axis is attached to it. The bracket with the lever is connected by a metal rod. When moving the structure up and down, no jamming occurs.

We fasten the drill bracket to the stand and attach the wooden lever

Due to the stability of the bracket, no complicated fasteners need to be invented. An ordinary long clamp of a suitable size is sufficient.

IMPORTANT! After the first tightening of the clamp, it is necessary to wait for shrinkage, and re-tighten the screw.

Such a mount is strong enough, while you can always dismantle the drill and use it as a hand tool.

Check the fastening of the drill with a clamp for tightening

We fasten the entire structure to the frame with the help of strong metal corners. It is this element that will account for half the effort during drilling. Also, the fastening of the round timber must withstand the weight of the entire mechanism and the actual hand drill.

Wooden round timber plays the role of a counterweight and serves as the basis for attaching a stand with a grinder to it

The drill stand must be equipped with a return spring. Its power is selected in such a way that the bracket with the drill rises smoothly without effort on the lever, and the drilling process is not tiring for the operator. Be sure to install a drilling stand so as not to spoil the bed. Quality doesn't matter, it's actually a consumable item. As a large number of holes form, the stand simply changes to a new one.

The machine drills confidently, the lever works effortlessly. Despite the simplicity of the mechanism - the hole is strictly vertical, there is no horizontal vibration of the drill. metal blanks they are just as easy to drill, the drill does not overheat and the drills remain intact. In principle, the design can be considered successful.

Steering rack drilling machine

Quite popular among domestic Kulibins is the design of a drilling machine from a steering rack. This steering element, after being replaced with a new one due to backlash, has a sufficient margin of safety for use as a lifting mechanism for a drilling machine.

If there is an old steering rack from a car, then you can make a drilling machine with your own hands

Making requires some skill and application of more quality materials than in the previous version. The dimensions of the steering rack imply a more massive drill, respectively, the bed and the rack are made of metal. A flywheel or other rotary mechanism is adapted to the place where the steering column is attached.

It remains to figure out how the rotation of the steering rack drive will be carried out

A bracket for a drill is installed on the carriage for fastening the steering rods. It should also be made of metal, since the weight of a hand-held power tool will be large.

We make a carriage for attaching a drill from a metal plate

The return spring is also selected more powerful, in accordance with the weight of the structure. In terms of reliability and workmanship, such a design approaches factory counterparts, and in terms of cost it will be no more than 10% of the purchased one. Therefore, this option can often be found in private auto repair shops or in the arsenal of coven mechanics.

In this video, the drill guide is made from ordinary scraps of metal, which will not be difficult to find and make yourself. The result is an excellent home-made rack, almost a drilling machine, which in terms of functionality is not inferior to conventional industrial designs intended for domestic use. But much more economical in terms of money.

Which design will the reader choose? The main thing is to strike a balance between cost, necessity and availability of materials.

Do-it-yourself drilling machine from a drill video tutorials

First lesson. Making parts for a plywood frame

Lesson two. Frame assembly

Lesson three. Connection of all nodes and the first start

obinstrumente.ru

Do-it-yourself guides for a household drill: options, materials and manufacturing technology

A drill is usually used to create holes in the wall. But at the same time there is no guarantee that it will turn out even. Therefore, to eliminate this drawback, it is necessary to use additional devices in the form of a guide for a drill. Using it, you can do this work with less physical effort. However, difficulties arise when drilling a hole at an angle of 90 degrees, and during certain work, the angle of the created hole often must be 45 degrees. In this case, it is necessary to carry out appropriate preparation of the working tool in order to fulfill this requirement.

A rather difficult task is to create a hole in structures made of too hard materials. This leads to slippage during the operation of the drill, which creates a danger to the worker and people around him, who may be injured. You can avoid such unpleasant consequences and at the same time simplify such a process with the help of such a device as guides for a drill. If necessary, they can be made independently, and the presence of a large number of options allows you to choose the most preferable among them.

The simplest guide nozzle for a do-it-yourself drill

Considering this version of the nozzle, one should take into account the fact that it will not be necessary to spend any money on the implementation of the idea. But at the same time, there will not be any special difficulties in the manufacture of a guide for a drill. But at the same time, the created device can serve for a short time.

materials

For the manufacture of the guide, it is necessary to prepare the following materials and tools:

plastic bottle;
plastic cover;
drill;
stationery knife;
felt-tip pen;
universal glue;
annular drill;
sandpaper;
drill.

Manufacturing process

First you need to perform certain manipulations with the drilling tool. To do this, a nut and a fixing drill are twisted from a drill. After that, its diameter should be marked on a plastic bottle as close as possible to the neck. Then transfer the circle corresponding to this diameter using a felt-tip pen. The end result should be a complete circle.

This template, which must be cut out later, should also be marked on the bottle cap, and care should be taken that its width is sufficient for this.

The next step is to cut the bottle or jar. The choice of the structure to be trimmed should be approached very carefully, as this will later affect the depth of the holes created using the guide.

Particular attention should be paid to work safety. To do this, it is recommended to sand the edges of the jar to make them even and smooth.

The holes that were previously applied to the bottle and its cap should be cut exactly along the intended line using a clerical knife. Processing should be carried out with the edges of the cuts, which must be thoroughly sanded. Then they take the lid and place it with the front side in the jar, acting on it with physical force to ensure the tightest possible fit. It is in this area that it is glued.

After waiting for the glue to dry, the drill attachment can be used for its intended purpose. A drill is inserted into it, after which, using a plastic nut, it is fixed on the tool and drilling of the hole begins. Although it does not have a depth selection option, this problem can be solved by making several of these nozzles and using the most suitable one as needed.

Straight Hole Guide

Even before creating a hole, you need to take care of the availability of the necessary materials: for this you can take a square bar made of wood or other material.

A drill, used in combination with a guide, is able to play the role of a small, simple drilling machine, with which you can perform various operations that require precise dimensions.

Important nuances

When deciding to create such a device with your own hands, you need to take into account such important points:

moving parts must be tightened as tightly as possible. For effective work, a do-it-yourself nozzle for a drill should have the ability to select a suitable reach and stroke. Moreover, if the guide post has a rather significant weight, then this only simplifies the process of creating holes.
In some cases, the rack can be used in combination with a vise, thanks to which the workpiece can be fixed. In this case, such a design easily turns into a full-fledged drilling machine. Moreover, it is not necessary to purchase such a vice in order to expand the functionality of the equipment. If you have enough experience, you can also make them yourself.

Conclusion

Drilling work is one of the most frequently performed during the manufacture of various structures. Moreover, the home master most often solves this problem with the help of a household drill. However, for the most part, the hole created does not differ in exact dimensions. And this can create certain difficulties when using it for its intended purpose.

You can get out of this difficult situation with the help of guides for a drill, which you can make yourself. Such an idea seems quite attractive for the reason that any owner can make such a nozzle, given that any means at hand can be used for this. However, having realized all the attractiveness of the guide, it must be remembered that it cannot become a full-fledged fixture for a drilling tool, so this nozzle should be used only in emergency situations. Otherwise, the drill guide will fail pretty soon.

stanok.guru

Do-it-yourself power tool accessories

For household repairs and work on suburban area various power tools are used. For them, specialized additional devices and devices are produced, many of which can be made with your own hands. Difficult industrial devices are better to get ready-made, and workbenches, tables, nozzles and almost everything else can be done without the help of others. Handmade devices for power tools can be adjusted to the required specifications.

Classification of devices for power tools

Do-it-yourself power tool accessories are generally classified into the following categories:

Tools and nozzles for processing. These are hand-held devices, which include grinding nozzles and bars for grinders, drills.
Devices for position modification, mounting certain angle cutting, drilling and more. These are the main surfaces, standards, guides. They will be able to carry out a different external type, often made of metal or wood.
Devices for dust extraction. Similar devices are used to remove sawdust, dust formation, and chips from the working plane. It is not so difficult to make such devices with your own hands, as a rule, previously existing fan holes in the equipment are used for mounting.
Do-it-yourself grinding nozzles, structures or bars, determined for surface treatment, are assembled. For example, for grinding wooden surface or cleaning the alloy, it is possible to use a wooden plate with a handle on top. In its working side, sandpaper of the desired grain size is strengthened. The platform model can be anything, it is only important to choose the right abrasive material.

Scheme of the device of the milling table

Devices for power tools happen different, but sometimes they have overall scales, as is the case with milling machines and saws.

It is recommended to choose an improved table that will contain everything, without exception, necessary for comfortable and safe work. The most common type is considered to be a milling table, made in the form of a large board with an opening for the router and a guide board. The scale of the worktop can be different, everything, without exception, depends on what kind of work will be carried out directly. The most ideal view is a table with legs of the required height. And the working and guide boards are made from a chipboard sheet. At the same time, vise, clamps can be taken into account on the surface. It is more correct to make the legs for the table as a whole replaceable, to provide a backup set.

Workbenches for power tools

To work with numerous devices, you will need to improve the workplace. For a home workshop or for a car garage, a small, small-sized and versatile workbench may be necessary. It is not so difficult to make it without the help of others, you just need to specifically make an improvement in your choice for which functions it is needed directly. It is more correct in general to make a workbench that can be used at any height, including on the table.

Then the power tool may become comfortable to have, change its position if necessary. For work, it is recommended to use various hardwoods, maple is considered a common material, which is simply processed, while possessing the required hardness and strength. For registration on the table, it is possible to attach comfortable legs or clamps to the unit. A workbench requires a vice, they are often used in work, which guarantees an improvement in its quality.

Drill bits

For a drill during operation, you may need various nozzles. They make it possible to simplify the work, make it easier, more comfortable, faster. The drill uses a huge number of homemade products, which numerous manufacturers today have taken as the basis for the study of specialized sets. The list of devices that you can make with your own hands is huge.

Accessories for power tools:

Various devices for power tools are needed in order to make the work most convenient and simple.

It is not always possible to buy such devices, of course, and often they are needed as a whole for a couple of times. For this reason, it is much easier to make them without the help of others, spending not so much time.

Few of the users know that an ordinary drill can perform very unusual functions besides drilling. For these purposes, there are very original devices for a drill that can expand its scope. Consider the varieties of nozzles and attachments that turn the drill into a completely different unit, capable of performing functions unusual for it at the household level.

This type of device is the most widely represented and has many interpretations.

To help the carpenter

Turns an ordinary drill into a small one home machine, which is used in the repair of furniture. By turning on low speeds and holding the device in a special mount, you can make a selection in the right place or machine a side groove.

Great precision in surface treatment is not expected, but this is not necessary, for example, when installing piano hinges - nothing is visible under them anyway.

Original nozzles

Sometimes it is necessary to drill holes in a very hard-to-reach place where a standard product does not fit due to dimensions, then use the original nozzles for drilling at various angles. The angle drive is ideal for use with any electric or cordless tool because it has its own chuck where the drills are clamped and the torque is transmitted through a gearbox and shank that is fixed in the main drill.

Such a device can be used not only for drilling, but also for tightening fasteners (screws, self-tapping screws and screws), cleaning and polishing hard-to-reach places - we clamp the desired bit or nozzle and perform the intended amount of work.

There are very unusual application fixtures that are used for an electric drill - pumps. They cannot work for a long time - they can be used to quickly pump out viscous paint residues from a barrel or ground water leaked into the cellar. Their performance is not very large, but you have nowhere to rush. The body of the nozzles is made of durable plastic, the service life is short, but the price is low.

Racks

To precisely drill the required holes in various materials apply special racks or rails, which can be purchased in stores - they provide vertical movement of the drill, clamped in a special basket. Their compactness, smooth running and accurate metric scale make them attractive for small workshop equipment, where the DIYer can accurately drill any holes, even in round objects.

A small vise with clamped workpiece can be placed anywhere on the bed and firmly fixed thanks to the grooves cut in the base.

Unique whetstone

On a sharpening drill various instrument you can install special nozzles - it turns into mini sharpener, which can be used to sharpen drill bits, circular saw blades, chisels, knives and different kind planes. The value of these attachments is that they help to significantly save family budget- the services of professional grinders of similar tools, especially drills, are quite high level prices.

The device of such nozzles allows you to work at different angles, and a cylindrical nozzle is used to sharpen drills. To sharpen other tools, special devices are used.

The photo shows the original nozzle for sharpening drills of any diameter and the machine for straightening circular saws. Installing various nozzles on a drill is not particularly difficult.

Woodworking

A drill can be used not only for drilling and as a mixer, it is worth attaching a special device to it - it turns into an original machine tool or a wood jigsaw.

Lathe

What home master does not dream of his own mini woodworking machine, but such devices are very expensive. There is a way out - these are unique attachments to a hand drill that have different design and the right tool for the job. These devices are not suitable for serial production of carved balusters and legs. coffee tables, but use them in the country or country house will be appropriate.

The design of the turning attachment for a drill is very simple and compact, any user can work - all you need is the desire and slowness of action.

It is hard to believe that a jigsaw can be made from an electric drill, these are quite different tools in their design, but nothing is impossible in the world. There was a designer who invented a nozzle that converts the rotation of the drill into reciprocating motion of the saw on wood. Now you can use a drill to cut boards of various thicknesses, and lovers of filigree woodwork can cut unique patterns from plywood with a jigsaw.

Sheet metal cutting

There are special attachments for cutting drills - they were developed by leading engineers of companies producing various models drills to facilitate work with roofing material. Roof work does not allow you to take a lot of tools with you, and going down each time to cut off the excess on stationary equipment is troublesome.

Using an ordinary cordless drill, you can cut off the desired strip from the steel sheet right on the spot or remove the excess. Using such a nozzle for cutting metal, you can cut a metal mesh, thick plastic, cut out a part of the required configuration and size from a whole sheet.

The unique device freely cuts metal, while you can change the angle of the tool and work not only at a right angle of 90 degrees, as ordinary metal scissors do.

Based on electric or cordless drill in a small workshop you can make many useful tools with your own hands, for example:

a device for a drill in the form of a drilling machine;
grinder;
sharpener for knives and scissors.

Some craftsmen even make homemade drills different power, which are used during repairs household appliances where a standard drill would be problematic to apply.

To drill a hole of the required diameter in a workpiece or part, there are special nozzle templates that make it easier for users who are a little unsure of their abilities - they call them a jig. There are already standard sizes for various operations, there are professional templates made of steel, and for domestic use- made of plastic or durable plastic.

The second common task is to drill many holes of the same type in one workpiece. Holding a drill in your hands, doing such work is long and inconvenient.
Since ancient times, locksmith workshops have used drilling machines of various capacities. But their cost for home purchase is too high.

In addition, the home master does not perform drilling on an industrial scale. Therefore, such a purchase will never pay off.

There are factory-made vertical drilling fixtures that can turn a hand drill into a full-fledged drilling machine. Many of them are equipped with coordinate plates and movable vise.

Stand vertical for drilling holes with a drill

This is a really convenient purchase, but the cost of such a machine is comparable to the cost of a drill. Therefore, home craftsmen often make a homemade drilling machine.

The main advantages of the design- cheap and the ability to create a fixture that is perfectly compatible with your hand drill. If there is an unnecessary photographic enlarger, microscope or other mechanism with a vertical feed of the working unit in the house (barn, garage), the task is simplified.

Homemade stand from an old microscope

It remains only to adapt the drill to the product. If there is no such bonus, the stand is made from scratch.

How to make a machine out of a drill using improvised materials

What should the guide stand for a hand drill consist of?

stable bed

Preferably with the possibility of installing a vice or other device that holds the workpiece. At home, it is made of thick chipboard, plywood, or textolite. In the center of the axis of the drill being installed, it is necessary to leave a hole with a diameter of a couple of centimeters.

Description of the necessary parts of a drilling machine from a drill

Guide upright

Here the imagination of developers is unlimited. It can be a bar, plywood plate, metal profile or pipe.

Main principle in the manufacture - a strict vertical in relation to the supporting frame. Otherwise, the drill will deviate from the rectilinear movement, spoil the workpiece and break.

Movement mechanism

It can be a lever type, or use a pair of gear-rack. It doesn't really matter which design you choose. It is important to observe the principle of the availability of materials, otherwise it may turn out that it is cheaper to purchase a finished product.

The mechanism for lifting and lowering is made by hand from boards

The second example of a lifting mechanism made of metal

Moreover, not only a drill can be supplied to the workpiece. Sometimes it is more convenient to lift the product to the drill. For example - on compact models.

Bracket for hand drill

Ideal Solution- use of a seat for a drill handle with a clamp grip. It encloses the shaft bearing and is optimally suited for centering the entire structure.

If you make accessories for a drill with your own hands, you can significantly expand the scope of this tool and make it easier to do many jobs. The capabilities of the electric drill can be expanded with the help of various nozzles, attachments.

Drill attachments

Using a conventional drill, you can not only drill holes of various diameters, but also saw, mill, pump liquids or make a lathe, drilling machine out of it. For this use various fixtures. Let's consider what they are. Do not think that the use of such attachments can make an electric drill a universal tool. It is clear that it will work worse than a special tool. But if you need to perform one-time work, then installing various nozzles on this tool allows you to use this device quite effectively for various purposes.

One of the most common devices that can be installed on this power tool are various kinds of stops.

This makes it faster and easier to work with this tool, and you will be able to make holes of the same depth. This is very convenient when working with thin parts or when you need to make a non-through hole.

You can make a parallel stop, with its help you can control not only the depth of drilling, but also the vertical position of the tool. It is very convenient when the drill can be turned into lathe. To do this, you need to make a device, the basis of which can be a metal channel. Two sleds are put on it so that they can move and be fixed. On the one hand, they make a mount for a drill, and on the other, a clamp for the workpiece, it is also necessary to place an emphasis on the cutter.

The workpiece is fixed and the tool is turned on, it rotates, and you can perform simple turning work.

Back to index

Building a Simple Drilling Machine

Very often, using a hand drill, it is not possible to make a hole exactly in the right place. This is especially felt when working with small workpieces. The way out of this situation can be the use of a bed for an electric drill, that is, turning a drill into a drilling machine.

Such a device has simple design and doesn't require a lot of money. It is enough to make a strong vertical stand, on which to fix the guides, the block on the bar will move along them. Equipment is attached to the indicated block. The simplest drilling machine is ready.

For the manufacture of the bed you will need:

stand, for this you can take chipboard with a thickness of at least 20 mm;
wooden beam with a section of 90x55 cm and plywood 10 mm thick;
a sheet of steel measuring 2x250x40 mm;
fasteners;
hacksaw;
drill;
measuring tools.

First, the main frame, which will be the base of the machine, is processed, sharp edges are removed. Racks are attached to it, which are made of plywood, for a reliable connection, you can additionally use corners.

Rails are made of metal, along which a slider with an electric drill attached to it will move in the future. For the manufacture of such a slider, a wooden beam is used.

The equipment must be firmly attached, for which it is necessary to make a reliable clamp. To facilitate the work, a spring can be attached to the slider, which will pull it up along with the electric drill and drill.

After you assemble the entire structure, you will need to check it and eliminate the shortcomings if any are found. Thus, you can create an elementary machine and, despite its simple design, it will be able to perform the same work as professional equipment.