Cutting logs into boards at home. The main types and methods of cutting wood. Circular and band saws for sawing logs and beams Multi-saw machines for sawing logs

Sawing a log into planks with a chainsaw is a fairly convenient and simple method of working with wood. Due to the presence of various nozzles, the master receives materials that have a smooth and even surface. It is easy to make boards on your own, it is not necessary to contact specialized stores.

Benefits of sawing logs with a chainsaw

The method of sawing logs with a chainsaw has several advantages.

The ability to work under any conditions - the chainsaw is not afraid of moisture, so specialists can saw logs during rain, the equipment will not deteriorate in this case.

High productivity - it is allowed to work on wood throughout the day, but keep in mind that the power of the device must be at least 7 horsepower.

Autonomous device - the equipment runs on gasoline, does not depend on electricity, workplace mounted on any site where it will be more convenient to carry out the process.

Ease of use - the chainsaw is equipped with a soft start and adjustable chain speed, these conditions provide a quality result for beginners in this business.

The undoubted advantage is that the equipment is much cheaper than a small sawmill. During a breakdown, repairs are inexpensive and do not take much time.

Types of working nozzles

Sawing logs with a chainsaw is carried out different ways, masters work with wood along the fibers, as well as across it. It all depends on what nozzles are used in the chainsaw.

Longitudinal cutter

It is used for sawing logs along, the process takes place in a horizontal position. After work, the master receives the same thickness of the product. Finished materials are exposed, after which the boards are used in construction.

By appearance the device is a small frame, it is attached to the tire on each side.

Sawing with a light nozzle

The method is not very productive, but is used quite often. The element is fastened on one side, but the workpieces are slightly uneven. Such materials are necessary for the construction of sheds or fences.

Drum debarker

With the help of such a nozzle it is easy to dissolve the log, it works due to the V-belt transmission. It is attached to the belts on both sides, for this purpose special pulleys are used. The speed of rotation of the shaft depends on the size of the pulleys, so the performance of the nozzle is easy to change.

This technology forces the master to carefully monitor each stage of the process, some specialists use an assistant during this cut. But this option requires increased security measures.

Features of a homemade sawing option

Cutting a log into boards is easy with a do-it-yourself tool. Making the equipment is easy:

• As a support, it is necessary to use a frame from a school desk or a pipe with a section in the form of a square, its optimal size is 20 × 20, and more is allowed.
• Build two clamps, mount a cross member with two holes for tie bolts at one end, make a protrusion for the tire in the middle.
• For longitudinal sawing of a log into boards, it is important to make a support frame, its width must be 7-8 cm less than the length.
• Then two elements 10 cm long are welded to both sides, holes are made for the bolts, a handle is attached in the middle for ease of operation.
• After that, insert the clamps into the grooves, the tire is installed, everything is carefully fixed.

It is not difficult to work with a home-made tool, this will require two goats, they will serve as a support, and it is also necessary to prepare a metal rail or board, the element will be a guide element. A log is laid from below, the required height for work is adjusted.

Log sawing technique

Longitudinal sawing is carried out using a horizontal nozzle. To get the boards even, it is important to use a specially prepared guide, its role is played by a metal rail or a high-strength board.

The most difficult thing in this process is to make the first cut, for this you need:

• Mount the leading ruler, it consists of two boards fastened together at an angle of 90 degrees.
• Install the log on supports, firmly fix its position.
• Check if the log is lying flat with a level.
• Using self-tapping screws, fix the leading ruler to the supports.
• In a horizontal position, fix another guide, the element will rest against the ground, but at the same time fix the log.
• Saw the log.

During the second cut, specialists may not use the leading ruler, the resulting board will serve as a guide. The second cut is carried out perpendicular to the first.

Cross cutting secrets

The cross saw is used to obtain firewood or decorative elements interior. Sawing is carried out according to the following principles:

• Place the log in a horizontal position on wooden supports, the height should be 0.5 m.
• To clean it from the bark.
• Using an ax or a saw, make small marks along the entire length, they should be located at the same distance from each other.
• Make cuts along the cuts.

Cross cutting does not require the use of special tools or nozzles. An ordinary chain is perfect for such work, but its rings must be strong.

Safety

When working with a chainsaw, you must follow the safety rules, they will help to avoid injuries and unpleasant situations:

• Do not allow people, especially children, to enter the work area.
• When working with a circular saw, be sure to put on a special protective cover on it.
• During the process of sawing logs, you should use means of protection against sawdust and noise.
• It is necessary to have a first aid kit with medicines to treat the wound during cuts.
• Do not pour gasoline into the heated tank of the chainsaw.
• It is necessary to use a chainsaw only for its intended purpose, it is forbidden to turn it on at full power if it is not in operation.
• Installation of logs is carried out only on the right side.
• While working with the equipment, it is strictly forbidden to put pressure on it with force.

If safety precautions are observed, the work will be simple, and as a result, high-quality material will be obtained without harm to health.

The chainsaw is a versatile piece of equipment that is easy to use. Its masters can use it on a personal plot, in a private house. In addition to receiving boards, it is used for repair work outbuildings and wooden decorative elements. Big number boards are not needed, just take a couple of logs.

Video: Cutting the forest into boards with a chainsaw

All photos from the article

The construction market is replete with a huge number of modern materials which, unfortunately, are not natural. That is why wood is still the most popular - due to its versatility and availability, it is used in various construction industries. Any lumber, whether it be timber or boards, is made from logs, so our task today is to understand how to make the necessary building material out of it.

Instead of a preface

1. Logs can be sawn with hand tool, or on various professional equipment used on an industrial scale.
2. The cost of finished lumber has a direct impact on its characteristics, namely the thickness of the materials and the amount of waste remaining as a result of the production process.

At enterprises engaged in the production of lumber, sawing lines are used. This equipment is highly productive and allows you to get a quality product.

Sawmill - a machine for cutting logs into boards

One of the types of sawmill equipment is a sawmill - a woodworking machine on which frame saws are installed. After processing, a timber and an edged board are obtained as a result.

Logs of only a certain size can be used as raw materials:

• length should not exceed 7 m;
• the diameter size range is much wider and ranges from 150mm to 800mm.

Round timber is also sawn on circular saws called circular saws or circular saws. These machines are divided into:

Most often logs are processed on band sawmills, allowing to cut a round timber both horizontally, and vertically. Due to the high quality of sawing logs, very little waste remains after obtaining the final material.

But this is not the whole list of equipment used for large-scale production of lumber. There are also highly specialized machines that are used only in certain branches of woodworking.

The main types and methods of cutting wood

The method of sawing logs is selected depending on the type of wood and what kind of workpiece should be obtained as a result.

Take into account:

• parameters that determine the size;
• form;
• surface quality;
• requirements.

Logs can be sawn according to the location of annual rings.

In total, there are three types of sawing:

1. Radial - along the radius of annual rings, while the work is carried out with particular clarity.
2. Tangential - the log is sawn to the growth rings tangentially, parallel to one of the radii.
3. Parallel-forming - cutting occurs parallel to the direction of the fibers.

Depending on the direction in which the logs are sawn, the methods of sawing them are also divided:

1. In collapse - involves sawing a log in several places along its entire plane. At the same time, they should be parallel to each other. This is the easiest processing method, which ultimately allows you to get a pair of slabs and an unedged board.
2. With slabs, it allows you to first get side boards and a beam, which, if necessary, is sawn into identical edged boards. This method allows you to cut a little more than half of all raw materials. The disadvantage is that the processing of round timber requires the use of two sawmills.
3. Segmented - a beam will be cut from the center of the log. This name is due to the fact that two segments remain on the sides of the log, which are subsequently cut into tangential boards.
4. Sector - round timber in this case is sawn into sectors. At the same time, their number depends on the diameter of the log and varies from 4 to 8. Further, the resulting fragments are sawn into radial or tangential boards.
5. Circular - designed for individual cutting of logs. In this case, healthy wood is separated from the affected one.

Tip: sawing off the next board, the trunk must be rotated 90˚ around the longitudinal axis.

It should be noted that the last three methods, unlike the previous two - the main ones, are used quite rarely.

Sawing at home

It is unprofitable to purchase sawmills for use at home both from an economic point of view, the price is quite high, and from a practical point of view. For these purposes, a conventional chainsaw is quite suitable.

However, you can also use electric, but gasoline is much more powerful and does not require electricity, which is very useful when working far from civilization. Despite the complexity of this process, with certain skills, labor costs can justify themselves.

All work related to cutting requires special tools:

• a device that fixes the log in a stationary state;
• nozzle frame designed for a chainsaw - if you want to get boards of different thicknesses, they are fixed on the tool tire, but in such a way as to be able to adjust the distance remaining between the nozzle and the chain;
• guide lines. It can be successfully replaced with a metal profile or an ordinary board of the required length, as long as it is even and rigid.

Tip: for a chainsaw, you need to purchase a special chain that allows you to make longitudinal cuts. Her distinctive feature is a special sharpening angle of the teeth.

Process

The operating instructions will be as follows:

1. Free the logs from bark and branches. The less waste you get, the more finished material will be.
2. Determine the cutting pattern that will be the most optimal. Why inspect the log for possible defects.

1. Saw in an east to west direction or vice versa. This is due to the fact that getting quality material possible only if the density of the boards is the same across the entire width. Please note that the density of the tree trunk on the north side is much higher than on the south.
2. Remove the slabs located opposite each other.
3. Saw the double-edged timber formed as a result of this operation into lumber.
4. Remove the edges from the resulting .

Tip: if any defects are found in the log, for example, a false core, it can be rotated as in circular sawing by 90 and 180˚.

Conclusion

If you decide to dissolve the log at home, you will have to use a sawmill, a chainsaw, or a regular saw. The first two options will show the best results, in addition, the process will be much faster and better.

Before starting work, it is advisable to draw a diagram for sawing round timber. The video in this article will provide an opportunity to find Additional information on the above topic.

Wood is the most popular material given to humanity by nature itself. Furniture is made from it, houses are built and even dishes are made. But in order to use wood as a building or finishing material, requires special machines for its processing.

The most popular material from wood it is a bar with boards, from which many construction blanks are made, but this requires sawing a round tree. It is for this purpose that band sawing machines (sawmills) exist.

Band sawmills

This type of sawing machine allows you to get from roundwood building material in the form of a board and a bar of various cross-sections and sizes with minimal waste. The board may not be edged, the edges of the board have a curved line, and edged (the edges make up a straight line). The bar can be square or rectangular.

The modern tool market today offers a variety of woodworking machines manufactured by domestic and foreign manufacturers. Among them are a large number of machines designed specifically for longitudinal sawing of round wood.

One of these is the tape model of the Taiga sawmill., which is by far the most in demand among entrepreneurs manufacturing lumber for construction, the furniture industry and other industrial areas.

Band sawmill "Taiga"

Peculiarities

Distinguishing properties

"Taiga T-1"

This sawmill model It has small dimensions and is driven by an electric motor. It is used for sawing round logs, as well as large timber into boards.

It has a durable metal frame. When sawing, there is no oscillation of the saws (waves). Sawing logs of small diameter. Differs in the low price, and low consumption of the electric power. small dimensions allow it to be transported even in a minibus.

"Taiga T-2"

It's practically an inexpensive machine. , whose power is only 7.5 kW. Its metal frame has a large margin of safety, which is designed for quite a long operation. The performance of the model depends on the type of product being processed, and can be approximately 5-10 cubic meters per meter. in shift.

Can be additionally equipped electronic ruler type Micron - 4, with the help of which full automation of control of almost all production operations is carried out.

The use of Micron - 4 helps the operator accurately, without errors, make a sawing map, mathematically calculate and make corrections for the thickness of the cut. In this case, all calculations are stored by an electronic ruler, which has 8 memory cells.

"Taiga T-2B"

According to their technical properties and performance, this model can be considered unique equipment. It is equipped with an economical drive from a four-stroke gasoline engine with a power of 10 kW (13 l / forces). When fully loaded, the engine consumes only about 1.5 liters of AI-92 gasoline.

To warm up the engine before the expected load, idling is provided, thereby extending its service life.

The design of the sawmill consists of a standard frame of the Taiga sawmill, but it provides fasteners for installation electric motor instead of petrol engine.

Machine T-2B can work in field conditions directly on the felled forest plot, where, of course, there cannot be an electric line.

Depending on the diameter of the sawn logs, Taiga-2B can cut about 10 cubic meters per one shift.

"Taiga T-2M"

This model of the band sawmill has a fairly powerful 11 ​​kW electric motor, thanks to which it is possible to saw large-sized logs with dense wood.

Its design has a fairly large margin of safety, therefore it is designed for long-term, multi-shift operation with a capacity of up to 10 cubic meters / m. in one shift.

At this sawmill, as well as on the T-2 model, an electronic ruler of the Micron-4 type can be installed, which automates many work processes.

"Taiga T-3"

The T-3 sawmill is designed for multi-shift work with wood of any density. Power

its electric motor is 11 kW, has a reinforced design of the sawing carriage, due to which the diameters of the sawing pulleys are increased up to 60 cm, which increases the life of the tape blades several times.

The design of this model is designed for fairly high loads, with minimum fast settings. This allows you to work without long breaks to adjust the equipment.

The performance of the T-3 model is, when cutting large round timber, about 12 cubic meters / m. in one shift.

The function of moving the sawmill along the log being processed can be separately configured and additionally equipped to automate the workflow with a multifunctional electronic ruler of the Micron-4 type.

The design of tape models "Taiga"

The basis for the sawmill can be a concrete platform or thick wooden beams laid on a flat area of ​​dense soil. Rails are laid on the bars or a prepared platform, which are rigidly fastened to each other. They also have a system for attaching processed logs.

The rails can be extended with an additional section, which makes it possible to cut logs, the length of which can exceed 8 meters.

The sawmill frame may have a mechanical or electric drive vertical movement and move on rails with support rollers in manual mode. Removal of saw cut is made manually one or two support workers.

The movement of the sawing mechanism along the vertical plane is carried out using a two-row chain drive simultaneously with the lowering/lifting gear drive, and is controlled by a metric scale located on the frame. Thanks to this, the sawing mechanism is fine-tuned in height and firmly fixed on the frame of the sawmill.

On the sawmill of the T-1 series, the sawing mechanism is moved manually by rotating the gearbox with a special handle. And on the rest of the machines, the vertical movement of the sawing mechanism is carried out by an automatic switch, but if it becomes necessary to adjust the saw in height, then it is done using a manual closer.

The sawing mechanism is equipped with two balanced rollers (leading and driven) on which the cutting saw is fixed. The drive roller is driven by a belt drive from an electric motor pulley. The driven roller is attached to the tension system and rotates from the movement of the belt.

Travel speed band saw may increase with an increase in the diameter of the pulley, which can be a maximum value of 520-600 mm. This improves the quality of the cut surface of the log and increases the service life of the cutting blade.

After installing the band saw, its tension is made with a special key with a dynamometer. Tension control is carried out on a scale located on the dynamometer sensor mounted on the tension wrench.

Constant tension and prevention of oscillation of the saw blade is carried out by the damping rollers of the sawing mechanism. The saw blade is equipped with a special lubrication system so that the saw blade does not get caught in the cut of the log, which can be caused by wood resin accumulated on the band. The system has a lubricant flow regulator, which simultaneously cools the cutting blade.

All moving and rotating parts of the sawmill are protected by a metal protective casing, and the machine is controlled through the sawmill keypad, which is installed on the saw frame.

Purpose and consumer groups

Preventive Maintenance

Preventive maintenance of sawmills consists in daily cleaning them of sawdust, lubricating the resting rollers and periodically inspecting all working mechanisms.

During service, worn parts are changed, mainly resting, as well as driving and driven rollers.

Wood, like natural stone, is one of the most ancient building materials. Despite the huge selection of various artificially created materials that exists today on the construction market, timber products are still very popular. In order to obtain high-quality lumber, a log must be sawn into boards. In this article we will talk about how to cut a log into boards.

Types of sawing logs

Sawing a log into boards is carried out in two main ways:

• radial
• tangential.

In addition, additional methods are possible:

• mixed
• semi-radial (rustic)
• central.

Radial sawing is a type of sawing, during which the axis of the cut runs through the core of the log and, as a result, the annual rings in the section of the board form an angle of 76 - 900. The lumber obtained by this sawing has a uniform color and texture. Timber almost does not undergo deformation during shrinkage and does not swell when moistened, because the dimensions of the wood change mainly along the line of the rings (across the fibers). In radial sawn lumber, annual rings are arranged in thickness. Such materials have the highest performance in comparison with other types of lumber.

Tangential sawing is carried out along the tangents to the lines of annual rings at a small distance from its core. The surfaces of the resulting boards are distinguished by a pronounced texture and a bright wavy pattern of annual rings. Such lumber is characterized by higher coefficients of shrinkage and swelling from moisture, compared to radial sawn boards. As a result, they are strongly deformed under the action of moisture. Such boards are in demand for use in dry conditions.

Rustic (semi-radial) and mixed types of sawing have signs of two main types of sawing at the same time: radial and tangential. Therefore, they show average shrinkage and swelling ratios. Rustic sawn boards are distinguished by straight lines of annual rings, which are located at angles of 46 - 75 degrees. to the layers. Mixed sawn lumber is distinguished by the fact that the lines change from straight at the edges (in width) of the board, to arched towards the middle.

The central cut is made right in the center of the trunk and contains its core. Taking into account the fact that the core of the trunk is the wood with the lowest strength values, center sawn lumber is characterized by a structure that is not uniform in strength.

Wood balance when sawing

Log cutting tools

Tools and cutting methods depend on the total volume of logs, such indicators as length, thickness. In addition, the quality of the future lumber must be taken into account. Sawing logs involves working with different tools and specialized equipment. In order to get a small amount of lumber at home suitable conditions manual method of processing logs using a chainsaw or traditional hand saw-hacksaws with teeth for the longitudinal type of cut.

The sawmill is perhaps the most known type sawmill equipment. This is a woodworking machine in which there are frame saws. At the sawmill, longitudinal sawn lumber is obtained, for example, edged boards or timber. Sawmills allow processing logs with a diameter of 15 to 80 cm and a length of up to 7 m.

Sawing logs into boards using circular saws is carried out by means of a saw disk type. Such equipment can be single-saw (single-disk) and multi-saw (multi-disk). Devices containing a single disk are suitable for working with small and not High Quality initial raw material. With the help of multi-disc machines, it is possible to cut round workpieces of large diameter.

Band sawmills are the most popular today. They are of two types: vertical and horizontal. The cutting tool in such equipment is a tape that is put on the pulleys. Work on band machines guarantees the production of quality longitudinal and mixed lumber, such as boards and timber. This generates the least amount of waste.

Large industrial enterprises use lines for sawing wood. They allow to achieve very high surface quality and precise geometry of the final products. Such lines are characterized by the highest productivity.

In addition to all of the above equipment, such types of highly specialized sawmill equipment are also used, such as debarking, edge trimming, band-cutting and other types of machines.

Very often there are situations when you need to make a very small amount of boards or beams for your own needs. Of course, buying machines in this case is absolutely not an option. Having certain knowledge and skills, it is much more profitable to cut logs with your own hands, using an electric or gasoline chain saw. Despite the fact that this work is quite laborious, the result is quite justified.

Most experts believe that a chainsaw is better suited for this purpose. Such equipment has high power and can operate without interruption for a long time. In addition, the operation of the chainsaw does not require electricity, so you can work far from the power supply, for example, right on the plot.

In order to cut a log into boards with a chainsaw, you will also need special tools, such as a mechanism for fixing the log, a frame attachment for a chainsaw, and a guide for cutting. The attachment frame must be attached to the chainsaw bar so that it is possible for them to adjust the gap between it and the chain. This will make it possible to create boards having different thicknesses. The chain should be purchased special, for longitudinal sawing. It has a special sharpening angle of the teeth. A guide ruler can be made from a metal profile of the required length or a flat rigid board.

Before starting work, you need to remove all the bark and remaining branches from the blanks, as well as carefully examine the log for various flaws. In this way, you will be able to choose the most suitable cutting pattern and, consequently, reduce the amount of possible waste.

If you are ripping trunks, you need to make sure that the resulting lumber is of the same density across the entire width. Since the density of wood from the northern part of the log is much higher than from the south, the cut is carried out in a plane directed from east to west (or vice versa).

The first step is to remove the slabs from two opposite edges of the log. As a result, a two-edged beam will be obtained, which is then cut into boards or other lumber of equal thickness, according to the planned sawing pattern. The end product is an unedged board, from which the edges are necessarily removed.

For many centuries, timber has been the most popular raw material for housing construction. Today, primitive processing methods have been replaced by modern equipment. For example, for sawing timber and processing them to the right sizes, craftsmen use sawmill. The disadvantage of such a machine is the cost. For this reason, many people make mini sawmills based on chainsaws.

video instruction on how to cut with your own hands, machine, sawing machine, photo and price

All photos from the article

The construction market is replete with a huge amount of modern materials, which, unfortunately, do not differ in naturalness. That is why wood is still the most popular - due to its versatility and availability, it is used in various construction industries. Any lumber, whether it be timber or boards, is made from logs, so our task today is to understand how to make the necessary building material out of it.

How to cut logs into boards at home

Instead of a preface

1. Logs can be sawn with hand tools, or on various professional equipment used on an industrial scale.
2. The cost of finished lumber has a direct impact on its characteristics, namely the thickness of the materials and the amount of waste remaining as a result of the production process.

Industrial machine for sawing logs into boards

1. To reduce the amount of waste, sawing logs on an industrial scale is carried out according to special schemes. living conditions sometimes there is a need for self-sawing logs, so you should first familiarize yourself with them.

What equipment is used

In production conditions, for sawing logs, various professional tools and special equipment are used, selected depending on:

• material length;
• its thickness;
• quality for products.

In domestic conditions, it is usually not available, but it is successfully replaced by a conventional chainsaw, a woodworking machine with a circular saw, or a hand saw for wood.

At enterprises engaged in the production of lumber, sawing lines are used. This equipment is highly productive and allows you to get a quality product.

Sawmill - a machine for cutting logs into boards

One of the types of sawmill equipment is a sawmill - a woodworking machine on which frame saws are installed. After processing, a timber and an edged board are obtained as a result.

Logs of only a certain size can be used as raw materials:

• length should not exceed 7 m;
• the diameter size range is much wider and ranges from 150mm to 800mm.

A board from the side of a log is called a slab

Round timber is also sawn on circular saws called circular saws or circular saws. These machines are divided into:

Most often, logs are processed on band sawmills, which allow sawing round timber both horizontally and vertically. Due to the high quality of sawing logs, very little waste remains after obtaining the final material.

But this is not the whole list of equipment used for large-scale production of lumber. There are also highly specialized machines that are used only in certain branches of woodworking.

Lining block house - a board under a log

The main types and methods of cutting wood

The method of sawing logs is selected depending on the type of wood and what kind of workpiece should be obtained as a result.

Take into account:

• parameters that determine the size;
• form;
• surface quality;
• requirements.

Logs can be sawn according to the location of annual rings.

In total, there are three types of sawing:

1. Radial - along the radius of annual rings, while the work is carried out with particular clarity.
2. Tangential - the log is sawn to the growth rings tangentially, parallel to one of the radii.
3. Parallel-forming - cutting occurs parallel to the direction of the fibers.

How to cut a log into boards with a chainsaw yourself

Depending on the direction in which the logs are sawn, the methods of sawing them are also divided:

1. In collapse - means sawing the log in several places along its entire plane. At the same time, they should be parallel to each other. This is the easiest processing method, which ultimately allows you to get a pair of slabs and an unedged board.
2. With slabs, it allows you to first get side boards and a beam, which, if necessary, is sawn into identical edged boards. This method allows you to cut a little more than half of all raw materials. The disadvantage is that the processing of round timber requires the use of two sawmills.
3. Segment - a beam will be cut from the center of the log. This name is due to the fact that two segments remain on the sides of the log, which are subsequently cut into tangential boards.
4. Sector - round timber in this case is sawn into sectors. At the same time, their number depends on the diameter of the log and varies from 4 to 8. Further, the resulting fragments are sawn into radial or tangential boards.
5. Circular - designed for individual cutting of logs. In this case, healthy wood is separated from the affected one.

Tip: sawing off the next board, the trunk must be rotated 90˚ around the longitudinal axis.

It should be noted that the last three methods, unlike the previous two - the main ones, are used quite rarely.

Sawing at home

It is unprofitable to purchase sawmills for use at home both from an economic point of view, the price is quite high, and from a practical point of view. For these purposes, a conventional chainsaw is quite suitable.

However, you can also use electric, but gasoline is much more powerful and does not require electricity, which is very useful when working far from civilization. Despite the complexity of this process, with certain skills, labor costs can justify themselves.




Do-it-yourself frame-nozzle for sawing logs

All work related to cutting requires special tools:

• a device that fixes the log in a stationary state;
• nozzle frame designed for a chainsaw - if you want to get boards of different thicknesses, they are fixed on the tool tire, but in such a way as to be able to adjust the distance remaining between the nozzle and the chain;
• guide lines. It can be successfully replaced with a metal profile or an ordinary board of the required length, as long as it is even and rigid.

Tip: for a chainsaw, you need to purchase a special chain that allows you to make longitudinal cuts. Its distinctive feature is a special angle of sharpening of the teeth.

Process

The operating instructions will be as follows:

1. Free the logs from bark and branches. The less waste you get, the more finished material will be.
2. Determine the cutting pattern that will be the most optimal. Why inspect the log for possible defects.

In the photo - cutting logs

1. Saw in an east to west direction or vice versa. This is due to the fact that obtaining high-quality material is possible only if the density of the boards is the same across the entire width. Please note that the density of the tree trunk on the north side is much higher than on the south.
2. Remove the slabs located opposite each other.
3. Saw the double-edged timber formed as a result of this operation into lumber.
4. Remove the edges from the resulting unedged wooden board.

Tip: if any defects are found in the log, for example, a false core, it can be rotated as in circular sawing by 90 and 180˚.

Conclusion

If you decide to dissolve the log at home, you will have to use a sawmill, a chainsaw, or a regular saw. The first two options will show the best results, in addition, the process will be much faster and better.

Before starting work, it is advisable to draw a diagram for sawing round timber. The video in this article will provide an opportunity to find additional information on the above topic.

rubankom.com

do-it-yourself video installation instructions, features of machines, devices for sawing logs, how to cut along exactly, in size, price, photo

All photos from the article

Very often during various works in construction, there is a need to carry out such an operation as sawing a tree into boards. In this review, we will tell you how you can organize the workflow depending on the conditions and specifics of a particular operation, since sometimes you need to dissolve only one element along the length, and sometimes you need to cut a whole log or beam.

In the photo: special equipment allows you to spread the board at different angles, but only those who are professionally engaged in woodworking have such installations, since their price is very high

What criteria should be considered when choosing a sawing method

All of the options that we will discuss below will help you to cope with the task, but each of them is suitable for certain conditions, so you need to decide on several factors in advance:

Important!
Sometimes the most optimal solution it may turn out to be the purchase of a finished board, especially if the amount of work is large.

Special machine for sawing boards along - perfect solution for those who perform rip cuts constantly and in large volumes

Types of equipment used

We will consider some options for doing the work with our own hands and talk about the devices used, you have to choose the solution that will be best for you in a given situation.

sawing the board

This type of work as a longitudinal cut of a board in size can be done in several ways:

• If the amount of work is small, then you can use a hand saw, though you will need a special option for longitudinal sawing, which differs in the shape of the tooth. The instruction for the work is as follows: it is necessary to carefully mark out using a square and a tape measure, then draw a clear line, then the element is carefully fixed so that the board does not move during the work;

The longer the board, the more difficult it is to carry out the process qualitatively.

Important!
Pay special attention to manual handling vertical position cutting blade, otherwise the edges will turn out to be jittery.

• The second option is to use a jigsaw for wood, but it is also suitable for small amounts of work, while the thickness of the board is limited, the marking process is similar to that described above. The work is easier to do, since you do not need to apply physical force and monitor the verticality of the cutting - the sole in the equipment ensures that the right angle is maintained;
• Now let's look at how to cut the board evenly along with the help of a circular saw, there are two options for carrying out the work: if the edges of the element are uneven, then a line is first drawn along which the cutting is made (most often this is done with unedged lumber), if one edge is even, then the stop is preliminarily set to a certain distance, and you simply drive the tool, pressing the stop part against the end;

When working, do everything in accordance with the instruction manual for the power tool

• Of course, the most simple solution The question of how to cut a board lengthwise is a circular saw, and both full-fledged installations and compact options can be used. This option is very well suited when cutting a large number of elements to one size, you can set the stop or attach it and not waste time marking and fixing, in addition, this type of equipment has the highest productivity;

Having fixed the emphasis, you can not worry about compliance with the parameters

sawing logs

A more complex option for carrying out work, for which more powerful equipment is needed. Of course, acquiring a full-fledged sawmill is not the best option, so sawing logs into boards in the field is done using a chainsaw and a special Timberjig kit.

Let's talk about this system in more detail:

• You will need a standard chainsaw, it is desirable that its power is quite high;
• It is also necessary to purchase a set consisting of a guide and stop, it is sold with a set of required fasteners, so no additional elements not required;

Design fits all standard chainsaws

• Next, a device is assembled for sawing logs into boards, for this, first of all, emphasis is placed on two boards, one of which is attached to the middle of the other with the butt end, a very strong T-shaped element is obtained, which will serve as a guide during the work;
• The log is placed on a flat base, after which stops are screwed to its ends, which are made of a board connected by a corner, it is important to control their level and position them evenly, the quality of the work depends on this;
• Now you need to attach the guide to the stops, it is set along the line of the future cut, while taking into account the fact that the chainsaw tire will pass 10 mm above the top edge of the guide. Fixation is carried out with the help of clamps, which are also included in the kit;
• A saw is located on the frame, the frame allows it to occupy the same position during the entire work. For convenience, we recommend that after fixing the log, raise the log so that the chainsaw is at an angle, so it will be much more convenient for you to work. The photo shows the construction in progress.

This is what the assembled system looks like.

Conclusion

Slitting wood is a tricky process that requires the right equipment and tools, but if done right, the result will be of the highest standard. The video in this article will talk about some of the described processes in more detail and in detail.

rubankom.com

Do-it-yourself multi-saw machine | Construction portal

Any production work that is associated with such a rather capricious material as natural wood is by no means an easy and rather responsible matter. No wonder that the slightest wrong move or negligent attitude to the work process can lead to disastrous results. Therefore, it is recommended to thoroughly study the “nature” of the workpiece being processed and choose the right multi-blade tape machine on wood. And you can assemble such an apparatus yourself if you know a lot about crafts with your own hands.

1. The purpose of the multi-blade machine
2. The design of the multi-blade machine
3. Principle of operation
4. Classification of gang saws
5. Do-it-yourself multi-saw machine

The purpose of the multi-blade machine

The main purpose of the multi-saw machine is the longitudinal cutting of unedged and edged lumber into blanks of certain sizes, as well as cutting unedged boards. It must be said that such a machine can handle any tree species. The number of saws can reach up to twenty-four. You can adjust them so that bars and boards of the desired width will be obtained. But still there are limitations: the thickness of the workpiece is at least 6 millimeters.

The gang saw can work together with the log saw, forming a single production line, as well as independently as a machine of the second row. It has become widespread in high-performance and medium-sized sawmills.

The machine provides different lengths workpieces have a rather high cutting accuracy due to the fact that the workpiece itself is not movable, but the staring module moves along the calibrating guide. The productivity of the machine increases when a laser ruler is installed.

Recently, a mini multi-saw machine has become more in demand due to its small dimensions. For a long time, it has served as a very good assistant in large industries and small-capacity enterprises, as well as in everyday life. If you choose this equipment, you can achieve quite good production results, that is, high quality products.

The design of the multi-blade machine

In various configurations, multi-saw machines are produced that allow you to cut beams (carriage) up to 160 millimeters high. It is used at construction sites and woodworking enterprises, can be installed both in unheated and heated rooms, is able to operate at temperatures from minus 15 to plus 35 degrees of the environment.

The rigid basis of the machine is a frame-type bed of welded construction, it serves to fasten and accommodate all assembly units. A set of saws is installed on the shaft, between them there are bushings, which are made depending on the size of the workpieces to be cut.

The roller feeding of blanks consists of two upper spring-loaded rollers, which are adjustable in height, and two lower fixed rollers. From an autonomous electric motor, the feed rollers are driven by a chain transmission through a belt drive and a gearbox. Claw protection, that is, the mechanism of safety stops, provides protection against the reverse departure of scraps and blanks.

It is possible to install up to 40 circular saws with a diameter of up to 500 millimeters on a gang saw. From this it follows that 1 cut of the workpiece can bring up to forty lamellas, as in the video about the gang saw. This possibility compensates for the low feed rate, which is adjustable in the range of 0.5 - 1.5 meters per minute.

On this woodworking equipment, when sawing a beam of a smaller height, saws of a smaller diameter can be used, this will reduce the width of the cut, as well as increase the yield of finished lumber in percentage terms. A saw with a diameter of 500 millimeters has a speed of 2850 rpm, and because of such specifications high quality lumber is obtained, that is, grades 0 and 1.

It should also be noted that quite different saws can be purchased for such a machine, for example, a bimetallic saw, stellite or band saw. When choosing a saw, you must strictly adhere to the recommendations given by the manufacturer. Maintenance saws consists in sharpening, which is carried out in a timely manner and with the help of special sharpening machines. Sharpening equipment is much more expensive for a disc gang than for a frame gang, and this feature is very beneficial.

The multi-saw machine can be additionally equipped with:

1. A device that on a gang saw machine controls the material feed rate. According to the readings of the ammeter, as well as from the load on the saws, the desired carriage feed rate is set. All this allows you to achieve a special mode of operation, where the saws and the electric motor of the machine work in the optimal mode without overloading. It also increases the useful life of the saws and reduces maintenance costs.
2. A device that automatically regulates the feed rate of the gun carriage (beam). Such a device makes it possible to eliminate the human factor when adjusting the carriage feed rate. On the saw shaft, depending on the load in automatic mode, the machine adjusts the feed rate of the carriage, which allows for maximum machine performance, and one of the most important thing is to prevent overloading the electric motor.
3. A device that is responsible for a soft start, and additionally protects against overloads, while monitoring its operation in real time. You can put a soft start device on the multi-blade machine, designed to ensure smooth start without overloading the machine in the electrical network, from the selected start modes (by time, by rated current).
4. Dust fan.

The principle of operation of the multi-blade machine

Such a tool is intended for sawing boards or timber with fairly high accuracy. These tools are sometimes called "sawmill", "multi-saw". Such names are explained by the principle of operation of the sawmill frame. What is this operating principle? The sawing process, which is carried out automatically, is carried out by saws that are stretched in a saw frame.

On a multi-blade machine, a board is laid on special gaskets and fixed at the end. During sawing with milling cutters, the board is pressed tightly, and therefore its displacement is not possible. The absence of receiving and feeding rollers is one of the main advantages of the gang saw. The saw carriage on the gang saw runs on a flat surface, and this ensures a smooth and almost perfect cut. A saw cart with cutters moves along the guides with the help of electromechanics. Smoothly adjustable feed rate.

With regard to saws, laser pointers help with the correct positioning of the board. Processing takes place simultaneously with two saws. The distance between the saws is regulated by a special handwheel, and controlled by the built-in ruler. Reliable fixation of the workpiece contributes to the pressure roller, adjustable in height.

With the help of the lower and upper feed rollers, workpieces are fed (the upper ones are spring-loaded, the lower ones are motionless). You can adjust the feed rate, step adjustment. On a multi-blade machine, the material feed speed is continuously adjustable. The optimal feed rate is set according to the readings of the ammeter, depending on the loads on the saws. This achieves the operating mode of the electric motor of the saw and the machine in the optimal mode without overloads.

With the help of interchangeable bushings, the adjustment of the saws is provided, which regulates the width of the manufactured lumber. From two operating sawmills, one machine processes unedged boards. Vibration is practically absent during machine operation due to the strength and rigidity of the welded frame.

To ensure that the material being processed does not fly out of the machine, it is equipped with claw stops that ensure the safety of the operator. A technological opening under the saw device is also provided for waste disposal. A special window is provided for turning waste in case of compaction.

Classification of gang saws

You got acquainted with the purpose and principle of operation of the multisaw. But before you start creating a multi-saw machine with your own hands, we strongly recommend that you find out what kind of multi-saws are. Conventionally, they are divided into frame, disk and cant. The last two are single and double roller.

frame machine

This type of multi-saw machine is designed for sawing timber into lamellas (boards) with high accuracy. The principle of operation of this machine is quite similar to the operation of a small sawmill: saws stretched in a saw frame cut a moving workpiece. The reciprocating movement of the saw frame is assisted by a crank mechanism.

Disc machine

Such multi-saw machines are designed for high-quality sawing of timber into the required edged materials. They have a higher quality and accuracy of the resulting lumber than frame gang saws. Here the tool that cuts is circular saws. There are two types of circular gang saws: single and twin shaft gang saws.

On a gang saw with an increase in the thickness of the timber that is being processed, it is necessary to use a larger saw diameter and a large thickness, respectively, this on a gang saw machine increases the width of the cut and, of course, the loss of wood that is processed into chips. Therefore, it is recommended to use a twin-shaft gang saw with a timber thickness of more than 150 millimeters, they use saws of a smaller diameter.

Chipping machine

Beaming machines are intended for longitudinal sawing of logs and are the first-line devices. They give out two slabs, two unedged boards and a two-edged beam at the exit. Chipping machines, like circular saws, are divided into single and double shaft.

There is also a complete sawmill line, which includes: a two-shaft canter, a conveyor with sawlog feeding to the canter, a driven roller table, a sorting table after the canter, a receiving roller, a slab processing complex and a multi-saw machine. At the same time, chipping machines can be installed both in the woodworking production line and separately from production.

Do-it-yourself multi-saw machine

A multi-saw machine in our time is a fairly convenient functional tool designed for cutting wood. Even alone with his help in short time can handle a lot of work. But not everyone is willing to pay for such a machine, because the price of a multi-saw machine is quite high. Many people think that the best option make it from improvised means with your own hands. For those who decide to make such a device themselves, we want to advise this.

A hand-made multi-saw disc machine is designed for cutting edges, for longitudinal sawing of wood, for the manufacture of edged boards, shalevki, wooden log cabins and much more. Self-made various beams, log cabins for a bath, various wooden floors will always cost less and of course better. It happens at a sawmill, you buy boards for the floor, and they are like a helicopter propeller when you start nailing one edge lower, the other higher. It is very uncomfortable.

It is best, of course, to make a homemade gang saw with three saws, although two saws would be enough, as experience suggests. The machine is designed for a three-phase network, and on the advice of "experienced" the engine should be powerful - 1.5 - 2 kW, and the revolutions - about 3,000. For the engine, it is advisable to make the shaft with dual bearings and 22 mm, because there will be heavy loads.

The belt is recommended to be installed with a section of "0" due to its rather large flexibility. The diameter of the saw shaft should be 20 millimeters. As the masters say, for do-it-yourself woodworking machines, in order to reduce the bending moment, the base should be minimal. The distance between the bearing housings must not exceed 300 mm. Also, the machine should be equipped with a soft start device to increase the life of the motor.

Now you have learned general provisions creating a gang saw at home. Depending on the purpose of the machine, its design may differ slightly. The main thing at the same time is that you perform all the work strictly according to the instructions, otherwise you will not be able to get the material of the proper quality at the output.

strport.ru

do-it-yourself video instruction for choosing, features of sawing circular saws, multi-saw household appliances, price, photo

All photos from the article

Wood sawing machine - a universal device with which you can perform a wide variety of work: transverse and longitudinal sawing, leveling the ends and trimming slabs, cutting elements required size, right angle beveling and bevelling at various angles. There are many different options on the market, we will consider the most popular and common ones.

In the photo: sawing household machines on wood can be of various sizes and with different characteristics

Key criteria to consider when choosing

Regardless of which type of equipment you choose, there are several characteristics that determine the features and operating parameters of a particular modification:

Power	A very important indicator that is directly related to the performance of the equipment. The larger the elements will be processed, the more powerful the engine will be required, if you often work with hardwood and thick workpieces, then most likely you need professional equipment with an asynchronous electric motor. The average power is 1.5 hp, but more complex tasks will require more productive options.
Voltage	As a rule, household appliances are powered by 220 volts, while professional sawing machines are powered by a three-phase 380 volt power supply. If you need the second option, then take care of drawing the appropriate line in order to prevent network congestion during operation.
Dimensions	It is impossible to put a machine with a large bed in a room measuring 2x3 meters, as there will be no room for feeding workpieces and movement. It is important that the space is sufficient for unobstructed access to any place of the fixture. If you need to work in different places, then the compact version is the best choice.
Workpiece size	Each machine has certain parameters that determine the thickness and width of the elements that can be cut. Therefore, decide in advance for what purposes you need equipment and what materials will be processed.
Desktop size	Another important factor on which the convenience of working with various products depends. So for sheet materials you need a large working surface, and for a board and a beam of small length, a small bed is enough
Additional functions	The presence of a dust removal system makes the process much cleaner, and the presence of a riving knife in the design prevents the workpieces from touching the back of the knife and prevents kickback. Also, modern machines may have an emergency stop system.

Important!
In addition to all the above factors, it is necessary to take into account another very big nuance: ease of maintenance and availability of spare parts in your area.
Most often, the supplier takes care of the service, but ask him for the availability of consumables and spare parts.

Multi-saw wood saws are professional equipment that can cut large timber and whole logs, they are used in woodworking enterprises and are very powerful

Equipment types

To consider all the varieties, it will take more than a dozen extensive articles, since there are many highly specialized installations that are used only by professionals. We will talk about the most popular options that can be purchased in almost any city.

A circular saw

A stationary circular saw for wood is an excellent option for large volumes of work and has a number of advantages:

• Robust cast-iron bed, which provides high sawing comfort and significantly reduces the vibration of the equipment. Its width can vary widely, you can choose best option both for sheet materials and for small elements.

Panel saws are one of the types of equipment that is distinguished by the fact that it is very convenient to work with it. sheet materials, so it is very popular among furniture manufacturers

• Good dust extraction systems, thanks to which the most comfortable working conditions are provided. The room will be much cleaner and you won't have to wear a respirator all the time.
• High power allows you to cut hard materials without losing the speed of rotation of the blade. The engine rarely operates at extreme loads, so it remains reliable for a long period of time.
• It is possible to install discs of large diameter, so that the thickness of the sawn elements can be very large. In addition, you can put cutting elements for different materials- both for wood and for plastic, chipboard and even aluminum.
• Modern models have a very convenient system of settings, you just need to enter the necessary data into the computer, and the installation itself will take the desired position. This is very convenient for a large amount of work and significantly increases the safety of operation, and also eliminates the occurrence of errors and miscalculations.

Circular saws for wood - high-performance professional equipment

Table extension equipment

• Sufficiently large power allows you to cope with most of the tasks that arise when building a house or in other matters not related to production. Although it is worth noting that this option is also used in enterprises as auxiliary equipment and for performing individual operations.

• The presence of a special stand allows you to significantly increase the working surface in the case of working with large-sized workpieces. When folded, the installation takes up little space, which is also very convenient.
• It is possible to install the stand and its quick dismantling if necessary, which greatly simplifies transportation.

Desktop options

Household wood saws are designed for small jobs and are considered a great solution for home use.

Their most important differences are as follows:

• The equipment has small dimensions, which simplifies their storage and weighs about 20 kilograms, that is, if necessary, you can put the structure on a workbench and remove it after work.
• The engine power is small, so you can not cut large workpieces, maximum width products is no more than 60 cm

Household appliances are light and mobile, but productivity is low

Jigsaw structures

If you need a machine for sawing wood, then this option is exactly what you need, judge for yourself:

• The main working element is a jigsaw file for wood, but on this design you can place the workpiece on the bed and process it as accurately and accurately as possible.

Jigsaw machine - perfect solution for those who need to carve complex elements from wood

• You can cut almost any shape from a flat blank, which is not available with other options.
• If necessary, it is possible to carry out longitudinal and transverse cutting of wooden blanks of small thickness.

Tape equipment

A wood saw with a cutting element in the form of a tape can be used both on an industrial scale for spreading logs, and in more compact installations, they can be used to cut small boards and timber, as well as various small elements.

The main features are as follows:

• The cutting thickness is much less than when using disc equipment.

Band saws are used for a variety of purposes.

• A convenient system of settings allows you to set the most accurate parameters.
• Pedal-start options allow you to free your hands during operation, which is very convenient.

Miter saws

This option is designed for quick and accurate cutting of ends with your own hands, but can also be used for longitudinal sawing of elements of small length, the following factors can be considered its advantages:

Miter saw - the most mobile option of all

• Ability to cut workpieces at various angles.
• There are two design options: simple, where the disc is stationary, and with a broach, where the cutting element moves along the guide, which significantly increases the processing width.
• The price of such devices is low, and the instruction manual is simple.

Important!
Miter saws are more convenient for mobile work on the street or on the roof, but for accurate cutting of boards and timber, it is better to buy at least a table saw.

Conclusion

The choice of a particular option depends on what kind of work you are going to do and in what volume, as well as how much money you have. The video in this article will help you understand this issue in more detail.

rubankom.com

A device for sawing logs with a chainsaw with your own hands

A huge number of domestic and industrial tasks require sawing wooden logs. For this, a whole arsenal of auxiliary equipment has been created, most of which is very expensive, which is why it is used only as a last resort. It is much easier to use a chainsaw for this, for which all kinds of auxiliary tools have also been invented, which greatly simplify not only the process of harvesting firewood, but also spreading logs onto boards even without the help of a stationary sawmill. In this article, we will talk about what they are and what is required for their independent production.

Classification of accessories for a chainsaw for sawing logs

Depending on the direction in which sawing will be carried out, all existing chainsaw nozzles are divided into 2 broad groups:

• for longitudinal sawing of the forest;
• for cross sections.

Both categories represent a range of industrial adapters that allow you to get boards and lumber of the required size, which can then be used for construction or repair.

When there are no factory options at your disposal, the only sure way is to make their counterparts at home.

Do-it-yourself chainsaw attachment for longitudinal sawing

It is based on enough simple design- a regular frame that is attached to the guide on both sides. If you make fasteners with only one, the cutting accuracy will be impaired, but this will not hurt to adapt such boards for the construction of utility rooms or wooden fences. Let's consider it step by step.

1. 1. As in the other case, we begin our work with drawings. They are the basis of factual material and the source of the correct course of work.
   2. We are looking for a frame for the future device (it can be an ordinary children's desk or a square pipe). It is desirable that cross section was at least 2 x 2 cm, and even a little more.
   3. We begin to make clamping elements. Their size should be at the level of 0.5-0.6 m. One of the end sides of each of them should become the basis for the aggregation of the next mechanical unit - the crossbar. It is best to weld it for greater reliability.
   4. In the already welded cross member, a series of holes are made with an electric drill, floor bolt ties. There should be a small protrusion in its center so that you can fully clamp the tire.

1. From above, we also weld similar fasteners, the photos of which you see on the right of the text.
   What else should be taken care of at this stage? When designing such clips, it is desirable that the height of the bar be somewhat less than the width of the bolts.
2. We begin to assemble the support frame. It doesn't have to be accurate. square shape. Ideally, its length is 1 dm more than its width.
3. It is necessary to attach two structural parts with a length of at least 0.1 m to its two sides in a perpendicular plane. This size is determined by the need to supplement them with clamps and tightening bolts. To this end, a hole is made again with a drill, and the nuts themselves are welded into the base. For ergonomics, you should also think about the handle, which can also be welded from improvised metal material.
4. The moment of the assembly itself, but here too there must be a clear technological concept. First of all, clamps are inserted into the groove elements, after them - the guide of the petrol tool, which must be very accurately fixed. How to choose the right distance? This is already regulated purely individually, depending on the thickness of the material with which you want to get the output.

Agree that such a course of action is very simple, and the most difficult, surprisingly, may be the lack of an electric welding house, on the basis of which the entire home-made cycle is built.

We make goats for sawing firewood with a chainsaw on our own

Wood processing, the purpose of which is to prepare firewood for the winter, cannot do without a well-known device - a goat, which not only facilitates this manipulation, but also allows you to do it yourself without attracting additional human resources. Every self-respecting homeowner, faced with such moments, is simply obliged to acquire such a "helper", which does not mean buying it. Like other devices, you can make it yourself, but how - we will consider in order.

• • We draw up a work plan with a detailed drawing so that this machine comes out geometrically correct. To simplify, we suggest that you familiarize yourself with the design, the leading parameters of which have already been calculated and marked in the photo below.

• • • We select durable consumables, including:
      • wooden bars;
      • columns made of strong wood;
      • metal profile;
      • metal pipes, rods and other things that make up the group of "home scrap metal".
    • Combining the above materials or choosing only one of the types according to the drawing, they proceed to the assembly of this auxiliary equipment.
    • The optimal height of the goat is 1 meter, although this parameter is adjusted depending on the height of the sawyer, the power of the chainsaw and the size of the wooden trunks that will be settled on it.

Each of the methods described, although it will lead to the final goal, still has one significant drawback - the lack of guarantees of personal safety, so this needs to be taken care of additionally.

Comments powered by HyperComments

sadovij-pomoshnik.ru