Laminate diagonally begin to stack with. Diagonal laminate: a new way to emphasize the originality of the interior (27 photos). Advantages and disadvantages

Reading time ≈ 9 minutes

If you want to create a unique and original design in your apartment using high-quality and affordable materials, try diagonally. Such unusual way styling will undoubtedly draw attention to the floor in the room and diversify it appearance. Especially this technique is used in case of incorrect wall geometry or non-standard layout.

Is diagonal styling right for you?

In order for the floor to become a decoration of the apartment, you need to determine exactly which laying technology is right for your interior, diagonal or straight.

Direct styling and its features:

It can be performed in rooms of any configuration with even walls and without any distortions of the box of a residential building.
Recommended for rooms with big amount pieces of furniture, as well as with carpets on the floor. The laminate in this case will not be very conspicuous, so you should not waste time and effort on the original installation. Graceful lines and interesting transitions are simply hidden behind corners and ledges.
The drawing should be laid parallel to the beam of light, so it is recommended to start the flooring from the far door. As a result, lighting will successfully hide gaps and seams between parts, which will make the coating perfectly smooth and glossy. However, this will work if the windows in the room are only on one wall.

Diagonal flooring and its features:

Diagonal laminate flooring is shown in the video below, it is also able to make the unsuccessful geometry of the walls invisible and visually straighten the layout.
The flooring technology in this way is more complicated than direct laying. It is desirable to have experience with the material, so that the result is of high quality and successful.
Laminate should be bought with a margin so that you can safely trim parts. The calculation of the material here is also carried out on an individual basis.

Laminate features:

Laminate panels are easy to lay on the floor in any room, even a beginner can handle it.
A wide range of models of various colors, textures, sizes and styles, which allows you to use this material in rooms with any interior and design.
Modern laminate is a durable and moisture-resistant floor covering that is resistant to abrasion and mechanical damage. It is placed not only in residential buildings, but also in areas with high traffic, for example, in offices, meeting rooms or conference rooms.

We calculate the consumption of material

First you need to decide on the layout method and decide whether it suits your layout and interior: from what angles should you start laying, and how much waste will remain after trimming the material. Laying laminate diagonally is shown in the video below.
Usually the area of the room is divided by the area of \u200b\u200bthe material in the package and the resulting value is rounded.
Never do the calculation offhand, otherwise the laminate may not be enough. It is also better to buy an extra pack of laminated panels with a margin.

There are two ways to diagonally stack panels:

From the corner, starting from the far window towards the door.
From one corner to another corner. This laying technology is called "deck", as the panels are laid out from the center. Using a special fishing line, it is necessary to determine the diagonal and make markings, and then start laying first to the left up to the corner, then to the right side. The layout process according to this method will be more laborious, but more economical. Since you will need to carefully mark up and more accurately calculate the number of lamellas. Laying laminate diagonally with your own hands is shown in the video.

Stages of diagonal laying

For proper styling you will need the following tools:

Roulette for measurements.
Ruler and pencil.
Wooden block to knock out the lamellas.
Mallet (carpenter's hammer).
Spacer wedges to secure gaps between panels.
Electric jigsaw.

Foundation preparation

To lay the lamellas, a flat surface is required so that the floor does not deform during operation and the material is not damaged:

Do not forget also about the substrate under the laminate panels. It can be cork or polyurethane, the sheets are laid end-to-end, and it is fixed with a special wide adhesive tape.

Stretch a fishing line, cord or rope between two corners diagonally to fix the direction of the future boards. The fishing line will help to control any slightest deviations from the angle of the lamella flooring. In the interior, diagonal styling at an angle of 45 degrees, but not less than 30, looks most successful.

Layout instructions

Consider in detail two layout methods: from the corner and from the center.

From the corner

Start the installation with one solid board, cutting it first under certain angle from both ends. This panel will set the direction for all other details. Also, start work from the corner where the pipes are present, having previously cut holes of the desired diameter in the board.

After mounting the starting lamella, move towards the center of the room. You will be left with a small open corner, which is mounted at the very end. You can cut it from any crop, which will remain in sufficient quantity.

As you move towards the center, do not forget to shift the transverse seams by ½ of the length of the boards. Fasten all elements of the laminate with ends, except for those that are joined to the walls. There should be a distance of 1.5 - 2 centimeters between the wall and the board.

Insert one panel into another and snap into place by lightly pressing on the floor. First you need to connect all the locks on the boards in one row, and then fasten the stacked row with the previous one. If you are working without a helper, use a small weight to help you fix the stack.

It is necessary to cut the extreme lamellas at a certain angle in order to repeat the line of the wall. To do this correctly, you need to measure the distance from the highest point of the row to the spacer peg against the wall, and then from the lowest point. We transfer these distances with lines to the panel, make markings and cut out the desired shape.

From the center

Use this method possible only when laying adhesive laminate. In the case of working with panels that have Click-type locks, such a layout is not possible, since some models do not imply a run-up from the center to the sides due to their structure.

The row in the center of the room with the longest panels is laid out first, it will be he who will set the direction for all the other boards. Installation is carried out in a known way, after which we move towards the left, and then to the right corner.

After installing all the lamellas, it remains to remove all the bars for spacers and mount the skirting boards.

Laying laminate can be done in any room, the main thing is to calculate the material consumption and take into account the geometry of the walls. In addition, such a floor will not require special care and will last you a long time. Master class video step by step instructions will help to better understand the technology and understand the intricacies of the process.

Having chosen laminate flooring for their living space, most home craftsmen decide to do all the laying work themselves. Well, great! However, there is one big “but” in this: an unprofessional approach does not take into account the individuality of each specific room. We offer you to understand the nuances.

In the instructions for the packaging of the laminate, the easiest installation method is indicated, which consists in placing the boards parallel to the walls. And it is precisely this method (it is written in the instructions!) that the vast majority of "home-made" ones follow. Of course, if the room in which the laminate is laid is of a strictly geometric shape (deviations of several degrees are not taken into account), then this method is preferable.

But if the walls are uneven, decorated in a semicircle, or are there simply flaws in the layout? In this case, another way of installing the laminate may be more successful - laying diagonally.

With the usual laying method, laminate boards are arranged parallel to the surface of the walls, and with a diagonal one, at an inclination of 30-45 °. Observance of a slope of 45 ° is considered optimal, but since adjacent walls are rarely strictly perpendicular, the angle within the same room may vary within the above indicated limits.

Advantages of laying in this way

Knowing how to lay laminate diagonally will come in handy not only when you need to hide layout flaws or smooth out uneven walls. Diagonal flooring is often used by interior designers when they want to expand the space of a narrow and dark room.

This approach will pay off especially strongly if the room is not cluttered with unnecessary furniture. Then the diagonal lines visually stretch the floor and, accordingly, it seems that the room has become freer.

Well, the last argument in favor of this installation method is that the diagonal floor pattern looks more interesting than the usual parallel installation. It opens up a real field for creativity and allows you to modify the room, stretching it, making it brighter, highlighting separate functional areas.

If you have a glazed and well-insulated loggia and you choose a floor covering for it, then you can use a laminate. In the next article we will talk about how to do it right:.

Calculation of the required amount of laminate

Diagonal installation is more complex than traditional parallel installation and requires more consumables. Therefore, when calculating the amount of laminate, it is necessary to plan for future waste of 15-20% of the material.

For professional builders who have extensive experience in laying laminate flooring, this percentage is not as high and approaches a minimum of 5%. But, since you are just learning, we recommend that you add 15-20% to the area of \u200b\u200bthe room and use this figure as the total amount of laminate.

An example calculation can be done here:

Technology and stages of diagonal laying

It is necessary to leave small gaps 1.5-2 cm thick between the walls and the laminated coating. These seams compensate for the swelling and shrinkage of the floor covering during temperature or humidity fluctuations.

To maintain the same distance around the entire perimeter of the room, you can use special pegs, which, after installation, are removed from the resulting seams. Then the gaps are closed with skirting boards fixed on the walls.

A problem for home builders-enthusiasts can be caused by the process of trimming the outermost lamellas in a row. You need to cut the edge of the board at an angle, and so as to completely repeat the outlines of the wall. To do this, measure the distance from the top point of the row to the spacer peg and, accordingly, from the bottom point to the peg.

The resulting distances are transferred to the whole laminate board in the form of two points - above and below. These points are connected by a line, along which the panel is subsequently cut. Cut the laminate from the back with a jigsaw or a regular hacksaw.

Thus, there is nothing supernatural in laying a laminate diagonally. A little more accuracy, preliminary calculations, planning and the amount of consumables are required. But as a result, you will get not only a beautiful and durable floor, but also the opportunity to visually expand such valuable square meters. And it's worth it, isn't it?

Laminate flooring can be laid in two main ways: straight (along the wall) and diagonally. For narrow long rooms, straight laying is better, and if the length of the room differs slightly from the width, you can resort to diagonal laying. The process itself is quite laborious and requires more complex calculations.

The main disadvantage of diagonal laying is an increase in material consumption (waste is 10-15%, and when laying in a straight line - 5%). But this flooring option looks advantageous and allows you to create more exquisite design. Since the eye usually glides along the long joints of the panels, this good way draw attention to the piece of furniture located in the corner.

The simplest calculation for diagonal laying is to determine the area of the room and add 15%, and then divide the result by the area of one laminate panel. There is also a formula for a more accurate count.

Let the length and width of the room be X and Y, and the length and width of the laminate panel A and B. In addition to these values, we need a number equal to the square root of 2, which is approximately 1.42.

The area of the room is determined as a standard, X * Y
Stock area according to the formula Y * B * 1.42
To get the total area of \u200b\u200bthe products that will be needed for work, add up both results
We divide the sum by the area of one laminate panel, we get the number of panels, round the result up

In general, the formula for determining the number of panels n looks like this:

Tip: for diagonal laying, it is better to purchase a laminate with shorter panel lengths.

Preparatory work

To cut laminate, you need a tool with fine teeth, it is best to use a special machine or a jigsaw, you can also use a circular saw. In extreme cases, a hand saw or a hacksaw will do, but for a large amount of work, a power tool is preferable. Cutting can be done as the laying is done, first having prepared panels for 2-3 rows. If sliced big number panels, they must be numbered so as not to get confused.

Important: the corners in rooms are often not perfectly straight, so you have to navigate directly on the spot to determine at what angle to cut the edges of the panels adjacent to the walls. Especially careful measurements are needed for the first 2-3 rows. If the panel is laid in a place where there is a ledge, a pipe comes out of the floor, curly cutouts are made according to a cardboard template.

Before starting installation, you must:

let the laminate rest indoors for at least a day
level, strengthen, clean the base
lay a substrate
prepare wedges for expansion gaps (you can use wooden blocks, laminate trimmings, optimal width 1-1.5 cm)

Possible installation options

Laying laminate diagonally can be done in 3 ways:

Laying starts from the corner, the first element has the shape of a right triangle
The first fragment is placed at some distance from the corner and has the shape of a trapezoid
Laying starts from the center of the room, from the line of its diagonal, the first row is prefabricated

As a rule, work is carried out from left to right, starting from the corner farthest from the doors. It is customary to lay the first row with a tongue (crest) away from you, with a groove towards you. Panels with a conventional lock (Lock) are located in the same plane and are knocked out with a light hammer through a wooden gasket for a tight connection. Since it is more convenient to drive a tenon into a groove, and not vice versa, it is better to start laying a laminate with such a lock from the corner and work in one direction. If a row consists of several panels, they can be attached to those already laid one by one or assembled in a row and connected to the previous one.

Clip-on (click) panels connect at an angle and snap into place, no padding required. The connection can be made on both sides, so this laminate can be laid from the center or set back from the corner.

corner stacking

On reverse side laminate boards, a right triangle is drawn with 45 ° corners (if the corner of the room is not perfectly straight, the necessary adjustments are made), with the hypotenuse towards the groove. This triangle fits into the corner of the room and wedged from the walls on both sides to form a gap. The unused part of the board will come in handy when laying in the second half of the room.

Then the whole panel is taken, a line is drawn from the edge of the side with the groove towards the side with the tongue at an angle of 45 °. From the obtained point on the side with the tongue, a segment is laid off equal to the length of the base of the triangle. The second point is connected to the base, so that an angle of 45 ° is formed again, an isosceles trapezoid is cut out. The same principle is observed when cutting the following elements - the length of the smaller base of the next trapezoid should be equal to the length of the larger base of the previous one.

When the length of one panel is not enough to fill the distance from wall to wall, rows of several panels are assembled, first from 2, then from more. Corners are cut only at the outer panels in each row. The panels must be laid with an offset of half or a third of the length, so that the seams run apart. Each next stacked row is wedged.
After half the room is covered with laminate, the direction of cutting the corners is changed, now the larger base will be on the side of the tongue, and the smaller one on the side of the groove. At this stage, you can use fragments that were previously formed during cutting.

Video: laying laminate diagonally from the corner

Stacking in two directions

Laying can start with a solid panel, it is cut at both ends at 45°, stacked with cuts parallel to adjacent walls, pushed into a corner as far as the walls allow, wedged. Next, several rows are assembled in the direction of expansion. The next row immediately after the solid panel can be made from two symmetrical fragments, and in the subsequent ones, the seams are shifted. When several rows are collected, you can fill the corner with smaller fragments. For ease of access, the assembled shield can be moved towards you, and when the corner is assembled, push it back, not forgetting the wedges.

If the laying starts from the center, it is necessary to connect the opposite corners of the room with a diagonal line, drawing it on the substrate.

Tip: it is difficult to draw a long line from corner to corner, it is better to pull the cord between nails or self-tapping screws hammered in the corners.

Then the angle between the drawn diagonal and the wall is measured and the first laminate panel is cut at the appropriate angle. It fits into a corner so that its wide base lies on the drawn line, and is separated from the wall with wedges. The required number of whole panels is connected to it at the ends, and the last one in the row is cut at the desired angle. Then the second row is assembled, which is a mirror image of the first, only the cutting must be carried out in such a way that the seams run apart. Further, laying is carried out on both sides of the center, suitable fragments are immediately used.

If the same flooring is laid in several rooms, and they are not separated by thresholds, the laminate is not cut along the line of the doorway, the following panels will be connected to the panels that extend beyond the room.

Video: laying laminate diagonally from the center of the room

Outcome

The laminate, laid diagonally, looks quite impressive, so that the labor and material costs are justified. Laying laminate with a tongue-and-groove connection is best done in one direction and starting from the corner. For snap-on laminate, the laying direction does not play a fundamental role, so new rows can be connected to the base from both sides. When laying from the center, small fragments are mounted last, a more rational consumption of material is ensured.

Development is not only in the technology of manufacturing materials for decoration, but also in the method of their installation. Laminate is a beautiful material High Quality. Recently, laying laminate diagonally in an apartment has become popular. This method is suitable for those who want to add zest to their interior, make it more individual. This type of installation will also visually expand the room. You can do the work yourself.

Calculation of the material for this method of laying. Is it true that it needs more than with traditional styling?

For diagonal mounting, it is necessary to calculate the amount of material using a special formula that differs from that used in the straight-line method. You need to take the length of the room and the width and multiply them. To this product it is necessary to add the product of the width of one board by 1.42 times the width of the room.

Mathematically, the formula for the calculation looks like this: AC - the width of the room; CD is the length of the room; 1.42 is the square root of 2; (ACxCD) + (1.42 AC x the width of one board).

Calculation of the amount of laminate per room

When mounting diagonally, you really need more material than with. It's easy to explain. The thing is that in areas where the ends of the panels adjoin the walls, they need to be cut in a certain way. So waste-free production will not work here. It is advisable to take material with a margin of 15-20%.

Laying laminate diagonally can be done by hand.

Laminate laying tool

You will need the following tools for this:

hammer;
tape measure with a pencil;
jigsaw;
padding bar;
wedges for spacers.

Before you start laying the laminate diagonally, you need to carry out certain preparatory operations. , get rid of the trash. In order to make the surface even, you can use self-leveling compounds. They are very easy to use and give excellent results.

It is better to sweep the floor first, and only then strengthen the floor with a primer.

After that, you need to cover the surface with cellophane. A substrate is placed on it or. Before starting work, it is necessary to hold the material indoors for about a couple of days. So it will not swell and will not shrink.

There are two ways to lay laminate diagonally: from the center and from the corner. Both methods are used quite often, but it is the first that produces the least waste. You can do the work yourself.

Method from corner:

Method from the corner

If you choose to install your laminate flooring away from the corner, you should start with a solid panel that is cut to the required angle on both sides. It is this panel that will indicate the direction in the future. It is important to remember that the panel must be wedged 10 from the wall in order to compensate for thermal expansion.
If there is a heating system near the corner in which you start work, then you should start from here. At the junction with the system, you can immediately make a cut. This will make the task easier. From the main panel it is worth moving towards the center of the room. With this laying, the rows will subsequently increase in length. So you should definitely offset the seams by about half the length of the panel. So the reliability will be much higher, and the floor itself will look more beautiful. Watch the tutorial video, you can quickly understand the editing system.
Panels in each row must be fastened at the ends. The exceptions are the segments that are adjacent to the walls. The row is laid out in its own place, while it is not linked to the previous one too tightly. After that, a measurement is carried out at 2 points. This length is reduced by 10 mm and transferred to the panel to be cut. It is important to note that if the walls are strictly opposite each other, then the angle that remains after trimming should fit exactly on the opposite side. So you will be able not to use up excess material.
After you have prepared the parts, remove the row from the lock, and then completely assemble it at the ends. And only after that is the clutch with the lock from the last row.

Method from the center:

Method from the center

Laying laminate diagonally can be done using the "from the center" method. With this method, you will first need to lay a long prefabricated row. He will give direction in the future. Its installation is carried out in the same way as described in the previous method. After that, it is worth starting the installation of the coating, first to one corner, and then to the other.

This technique is justified for those rooms in which there are external corners.

The first row is better to start from the outer corners on a tangent. After you finish the installation, you will need to remove the spacer bars and attach the plinth to the wall.

How to remove the end panel

Removing the end panel

Measure the length to the wall. Transfer the measurements to the material. Measure the length from the opposite end. Again transfer the measurements to the material. The points that you have turned out will need to be connected. It is better to cut with a jigsaw from the inside out. So on the front you will not have chips.

Fasten all locks

To lay them out, you need to fasten all the locks. Place one panel at an angle to the other. Next, press the floor, the lock will snap into place, so you need to fasten all the rows. Now fasten the sides, the more you have made the row, the more difficult it will be to snap it into place. The technology is the same: slightly lift the opposite edge. Install the timber in the lock, press on the floor and snap into place. In order for the panel to enter its position, you can shake it slightly. And to see the process more clearly, turn on the video.

This method of installation in this way has its pros and cons.

Mounting method

Its main advantage is beauty. You can easily hide the imperfections of the room. The disadvantages include a greater consumption of material.

If you decide to install the laminate in the apartment, then you can do it yourself.

To do this, just watch the training video. Such a floor will look very unusual and elegant. It will make your room look bigger.

Video

In today's video you will see how to properly lay the laminate diagonally in the master class.
Thanks to this material, you will learn a lot of useful things for yourself.

Photo source: laminatekspert.ru, strmnt.com

Laminate today is chosen by many for flooring - it is not only very convenient to choose it for the design solution of almost any apartment, but it is also quite easy to lay it yourself and without extra expenses.

Those who are at least superficially interested in this issue know that you can lay the laminate in either a straight or diagonal way. Both of these methods have their advantages and disadvantages - for example, a straight line is perfect for laying on your own, even if there is not enough experience in this matter, however, this method can only be laid in a standard layout room - elongated in length. For square rooms, it is necessary to lay the laminate diagonally - how to do it correctly, we cover in this article.

Despite the fact that the installation of a laminate floor is a technology that requires compliance with technical recommendations, it is quite possible to do it yourself. Let's take a closer look at how you can lay a laminate diagonally, what are the advantages and disadvantages of this process, and also compare different flooring laying methods.

It's no secret that today laminate flooring is at the peak of popularity, so for the majority there is a question of installation - and some prefer to do the work themselves, adjusting the finished result to their needs and requirements, as well as making quite significant savings.

Most often, those who do not have experience in laying the floor do it in the usual direct way and lay out the panels in a straight line, along the walls in the room.

Such a solution is good only for those rooms that have the correct shape - if there are such features as an unconventional shape or rounded walls, it is the diagonal laying method that will help.

If, with the standard method, laminate panels are laid so that they are parallel to one wall and perpendicular to another, then otherwise they are laid diagonally at an angle of about 45 degrees. As a rule, it is this angle that allows you to achieve optimal results.

Advantages and disadvantages of the method

One of the main advantages that I would like to highlight is an interesting and original look of the room, a good design solution that visually adds volume to the space while maintaining the usual length and width. Coatings laid out in such a way look neat narrow rooms which are strongly elongated. If the room has the shape of a hexagon, has niches or roundings, then with a direct laying method, most of the flaws will be immediately noticeable.

List of advantages:

Disadvantages, unfortunately, are also present:

In general, with a competent approach, this method has much more advantages than disadvantages.

How to prepare

The fact that the foundation is extremely important in the implementation preparatory work, every prudent and careful owner should know. After analyzing what material the base is made of, it will be possible to choose the right type of preparatory work. Usually there are two various types bottom base.

Concrete

Usually about concrete base it is a question if the repair is carried out in apartment building with many floors. In this case, the preparation will begin with pouring a screed of cement and concrete - this is not difficult and accessible to everyone. There is no need to attract outside forces and employees.

Here are the main things to pay attention to if you have a concrete base:

the screed will dry out for at least 3 weeks;
to cope with drying faster, add plasticizers to the prepared solution;
be sure to make sure that the screed is neat, without cracks and indentations - such details can significantly harm and bring only problems in the future. To avoid this, it is easier to simply change the screed to a new one.

If you take into account all these nuances, the result will be of high quality and faster.

floor screed

wood base

Of course, wood is a much less durable and stable material, despite the abundance of all kinds of impregnations and compounds. That is why, before laying the laminate, try to perform a few simple steps that will allow the floors to last longer:

List of tools

First of all, we need a saw with fine teeth, a special machine, a jigsaw or a “circular” is also well suited. However, remember that hacksaws for working with metal and hand saws won't fit.

Additionally, purchase a hammer, measuring tape, bars and wedges, as well as pencils and rulers for taking measurements.

How long will laminate flooring take?

It is very simple to perform an accurate calculation of the number of boards required for work with the classical method - it is enough to find out the ratio of the total area of \u200b\u200bthe entire room and the area of a single board.

In this case, first lay out large panels and cut them at the end to right size, then, in the second row, you will need to put whole panels, in addition to the last one - it is carefully cut to reach the desired size. Do the same with the third, and with any next step.

IN general principle laying will practically not differ from that of direct installation - with the only difference being that the trimmings will be triangular, and initially the amount of material should be prepared more. So, the amount is calculated from the area of \u200b\u200bthe room, however, it will be necessary to add approximately 15 percent of the amount of material for additional waste. For particularly experienced installers, this number can be reduced to 5 percent, with averages around 10 percent.

Interesting! This amount of stock will be required when laying at an angle of 45 degrees, if the angle increases, then there will be more waste. It is better not to deviate from the gold standards.

What rules to follow

A little trick from the owner: pieces of laminate that are left from the first laid row can be a great start to the next.

It is best to stick to an angle of up to 45 degrees (permissible - about 30). This installation method is good for rooms with a width of up to 6 and a length of up to 8 meters.

In what cases the laminate is not laid

Not always laminate good option for flooring. There are conditions that make this type of coverage impossible, or impose certain restrictions on use.

First of all, you can’t put a laminate coating on glue (or any similar method) - not only does it look terrible, it also reduces the durability of operation. Shrinkage of the building or temperature changes will cause the coating to simply move.

Interesting! Laminate is an unsuitable option for those rooms where the natural humidity of the air is higher (this applies to saunas or baths, showers, open spaces, balconies and terraces).

If the room involves high traffic or the constant presence of a large number of people, then it is better to give preference to another material that is more resistant to wear.

Laying technology: making the right choice

Remember that the choice of technology for laying is a very important task that cannot be neglected. Here are the main techniques.

Method	Description
Adhesive mounting	With it, laminate boards are fixed with the help of adhesive mixtures specially selected at the end. This method is good in that there is the possibility of good sealing of the butt areas, good waterproofing, no deformation and resistance to change. temperature regime. Such installation is quite easy and simple. However, the disadvantages include the impossibility of replacing individual elements if they are damaged - only through total dismantling.
Castle Click	This method is considered one of the most popular - this is how the laminate is mounted quite easily, the method is available even for beginners, and the boards are attached at an angle using such a system, which allows you to quickly and conveniently dismantle the coating partially if damage or other deformation of the board occurs.
Castle Lock	The Lock Lock method is similar to Click, however, the parts will be attached exactly in the horizontal plane - for example, when installing boards between walls or making a second row in length if the distance between the rows of boards is small. The boards are knocked down with a bar and a hammer between two rows. All rows will subsequently be mounted in the same way, without changes.

Step-by-step instructions for the technique of laying laminate flooring diagonally

As we have repeatedly mentioned before, any laying of flooring begins with good preparation - first, the base is leveled, all irregularities are eliminated, after which all debris, dirt and foreign objects are completely removed.

The second step of preparation will be the implementation of the substrate layer - usually the sheets (if the substrate is sheet) should be laid out with a spread of joints - the sheets are bonded using adhesive tape. If you prefer a roll substrate, then everything is even simpler - the sheets are rolled out in rolls over the entire floor area from wall to wall. If there is a pipe or other element that cannot be eliminated in the way of rolling and laying the base, it will be enough to carefully cut the substrate.

The first method: the starting point for laying the laminate floor will be the corner of the room farthest from the door, a triangular fragment of the coating is placed in the corner, which is formed by cutting the board at an even angle of forty-five degrees. Next, the elements are laid at the same angle - they will be trapezoidal boards.
The second method: we lay the laminate from the central point of the room, which is determined by the intersection of the diagonals of two opposite corners. In this case, the first laid out row will be the longest, it will need to be laid out from several elements of the laminate flooring.

Remember that gaps will need to be left near the walls and elements of the heating system. For their uniformity, use specially selected wedges or just trimming laminate boards.

Not sure how to cut material at a precise 45-degree angle? There is nothing easier - use a regular square and create a template for cutting material.

Angular way

This is the simplest and most common method of laying laminate flooring. It is recommended to make sure that the long sides of each board (panel) are located in the direction sun rays that enter the room - this will achieve less visibility of the joints, the floor looks more uniform and neat.

The boards, as already mentioned, will have a trapezoidal shape. Accordingly, the length of the top side of the board will be equal to the bottom side of the previous laid trapezoid.

Step-by-step instruction.

Accurate measurements are carried out taking into account all allowances and technological gaps. Use a tape measure and square, and also use the prepared template. All lines will be drawn using the most ordinary pencil. The edges are cut with a hacksaw for wood or a jigsaw along the previously drawn lines.
If more than one board is laid in a row, it will be necessary to cut the first panel on the left in the form of a triangle.
The boards will be connected to each other in one row with their short end sides, after which the already assembled row is connected to the previously laid one.
Once you have laid last panel, the final connection of the last row is performed, the floor will need to be tapped and compacted.
In the same way, you will gradually lay out all the rows one after another and approach another corner of the room - the cutting direction will be changed, now we are moving not from short rows to long ones, but exactly the opposite. All rows will be stacked in the same way.
All rows must be stacked the same
Our laying ends with the installation of the last triangle small size, which you cut out of the panel in advance - it will be exactly the same as the triangle that you laid the very first.

Laying method from the center

If you have made up your mind and decide to lay the laminate diagonally, starting from the central part of the room, follow these recommendations.

Draw a conditional diagonal between opposite corners of the room. The method is up to you - you can simply draw this line on the substrate or stretch the rope from one corner to another.
Next, try on the size of the cut angle on the first board between the rope and the wall closest to it - once you have drawn the cut line on the board, cut along it. This board is placed with the long side on the diagonal, leaving wedges near the wall to fill the gap.
Then other panels are attached to the first board with the short sides, while the last board at the bottom must be cut to the desired size at the desired angle (you determined its size earlier).
All the following rows are laid in a similar pattern, the joints are displaced according to the principle chessboard. Thus, you will come to the conclusion that in adjacent rows the joints will be obtained with an offset - this will allow flooring be stronger, less prone to deformation.
Also, according to the type of checkerboard, end joints in adjacent rows will also be located.

Summing up - first connect the ends of the panels (usually with locks), then fasten the already assembled rows with the long sides with the previous rows.

The most convenient thing is to carry out such installation together, because you will need to connect several boards in long rows, help will not be superfluous. If not possible, then just use a small weight: once you have connected part of one row and snapped the locks, just press the weight on the connected boards and continue to interlock the parts in the row. Do not be afraid - the connected boards should not fall apart.

Keep a technological gap of about 10 mm between the walls and panels - this will allow the floor to lie more evenly, especially if there is often a change in climatic indicators in the room. You will later remove these gaps under the baseboards, they will not be noticeable.

Mounting Features

It will not be superfluous to pay special attention to how best to arrange the points of contact between the panels and the heating pipes.

The first way is to drill a hole in the panel, which will be approximately one and a half centimeters larger than the diameter of the pipe. This gap can be made on two butt boards by drilling a separate semicircle on each. Or, if you want, then drill a hole in the board, and after that, divide the laminate sheet into two halves.

In order to seal the place where the panel joins the cutouts and pipes of the central heating (or other elements that cannot be dismantled), use sealants.

As you can see, everything is very simple - laying a laminate flooring in a diagonal way is not very difficult, it only requires accuracy and clarity in budgeting and calculating the material. Without planning, it is better not to proceed with this method. As a result, you will have a neat and beautiful floor with an unusual coating effect that you could do with your own hands.

The room looks more spacious, it has more visually defined space - this will be a huge advantage for apartments with a small living space.

When installing, pay attention to the fact that it may be difficult to purchase products from brands such as Kronotex, Berry Flur, Tarkett, Vitex and Pergo. The fact is that each of these companies has a number of developments that can affect how the panels move, what type of lock and its size. If you find yourself having difficulty connecting blocks, then create rows with alternating short and long locks.

Interesting! The most accurate way to cut the material with electric jigsaw from the wrong side - so you save the surface from chips.

Laminate overlay cement screed usually performed no earlier than a week after application. In winter, it is better to wait three weeks or even a month. To level wooden floors, use OSB boards, isolon or substrate.

jigsaw

In no case do not lay the laminate in continuous for the entire apartment, especially if the coating is laid in several rooms at once, in the hallway and in the kitchen. Try to make sure that each room has its own individual direction of laying the panels.

If parquet is used as a base, be sure to repair it so that it does not creak.

If you are still not sure that you will be able to lay the laminate on your own, it is better not to risk it and enlist the help of specialists. The overpayment for a quality installation will more than pay off with long-term operation and the absence of the need for repair work.

Remember that laminate is sensitive to water, so do not use adhesive compositions water based. Also avoid sand or small gravel, which can scratch the finish. After installation is complete, wipe the floor with a microfiber cloth.

Laminate floors look noble, neat, they are durable and of high quality. Be sure to take into account the temperature and humidity in the room.

When laying, sort the trimmings and try to use them as much as possible during installation.

Medium-sized panels are well suited for diagonal installation.

Diagonally laid laminate: interior solutions

Try to experiment: for example, panels of colors that contrast with each other or just shades that are slightly different look good - this gives expressiveness to the flooring.

There should be a slight difference in color from the walls - this general rule interior design. Try not to overload the room with dark or light colors in the interior.

Of course, dark laminate can also be laid diagonally - it will look good in offices and bedrooms.

Summing up

In the article, we outlined the basic rules for installing and laying a laminate flooring made in a diagonal way. Despite the fact that this is a rather time-consuming and sometimes more complicated process than laying with the traditional direct method, the result is usually much more advantageous and creates room for creativity and imagination. The room will look much more beautiful and original, often the appearance of the room is truly transformed. Use different colors and feel free to look for your own solutions.

We examined the main advantages and disadvantages of this method, as well as the features of its self-laying. If you want to flooring looked good and harmonious, then we recommend that you stop at this method.

Feel free to experiment, learn new things and get acquainted with interesting design solutions- and good luck in transforming your home!