Types of corrugated board (profiled sheet) for the construction of a fence. Which profiled sheet is better for the fence Choice of dimensional indicators

If it is decided to make a fence from a profiled sheet around suburban area or a private house, it will be useful to read the tips on how and what to choose a corrugated board for the fence.

Recently, the profiled sheet has turned from an inconspicuous galvanized bent metal profile into an attractive material with a wide range of colors, textures and configurations. And that's just what's on the surface.

How to choose a corrugated board for a fence? Which one is better or worse? What are the parameters of corrugated board that determine exactly for the fence. Is it possible to use roofing corrugated board on a fence? These and other questions will be considered within this article.

The first thing to consider is the parameters of the fence itself:

length;
height;
frame.

These are the three pillars on which all further calculations of corrugated board are based and have a direct impact on the choice.

Second, determine the duration of operation

The service life (temporary or permanent) is an important point, which, along with the fence itself, will determine the installation budget. The cost of a fence made of corrugated board may depend on the parameters of the fence, which are difficult to change, and on the price of a profiled sheet, which is determined by the quality of the metal profile (which in turn affects the estimated period of operation of the fence).

From this point of view, a corrugated board fence can be temporary (fencing a construction site) or permanent (fence near a house). The longer the service life of the fence is expected, the more scrupulously you need to approach its choice.

Which corrugated board for the fence is better to choose

To make a choice and use right material, you need to evaluate the main parameters:

1. Coating of corrugated board

Like any metal, corrugated board, which is based on an iron core, is subject to corrosion processes. To slow down the process of rusting or prevent it, the profiled sheet is covered with special coatings, the type and thickness of which determines the cost and service life of the corrugated board.

There are two types of corrugated board on the market, each of which has varieties:

Without decorative coating

3. The thickness of the corrugated board for the fence

The most controversial of the options. The fact is that the thickness of the profiled sheet directly affects the strength of the fence.

What thickness of corrugated board to choose for the fence?

Sellers are advised to purchase thicker metal - 0.5-1 mm. However, the masters and many users agree that a reliable frame is able to compensate for the small thickness of the profiled sheet. From the point of view of cost and labor intensity of work, this is a moot point, but the fact that a strong frame is able to level the windage of the sheet and gives it rigidity is unequivocal.

Therefore, most optimum thickness for users is 0.45. Considering the allowable GOST 24045-2010 and EN 10143 deviations of +/- 6 mm. in fact it is 0.39 mm. Nevertheless, professional installers give a guarantee for a fence with such a corrugated board.

How to check the thickness of corrugated board?

The seller is obliged to provide all sheets for measuring the thickness. As for the thickness of the zinc coating, there are three options - either take the word of the seller, or demand documents for the metal coil from which the corrugated board is rolled. Again, you need to remember that documents can be for one bay, and the rental is made from another. The third option is to send the sample to the laboratory for analysis. But installing a fence from corrugated board with your own hands is not such a large project as to spend a resource on analyzes.

4. The color of the corrugated board for the fence

Color does not affect the strength characteristics of the fence, however, it determines the visual appeal and affects the price of corrugated board.

All manufacturers (except Ruukki (Finland), which use the RR color layout) use the standard Ral chart for color designation. Thanks to this, the corrugated board of different manufacturers is designed in the same color scheme.

How to choose the color of corrugated board for the fence?

The question is rhetorical, but according to statistics, among the favorites are 8017 (brown), 3005 (rotten cherry), 6005 (green), 6002 (light green).

Today, a popular solution is to use corrugated board coated with prints with wood, brick, stone, etc. patterns. Printech corrugated board with imitation looks very advantageous in the finished product. And the decor, in the form of columns, columns or forged parts, only gives the fence solidity and prestige.

Note. It is important to know that any coating is exposed to ultraviolet radiation, i.e., it burns out. But, a high-quality coating burns out evenly. In terms of speed, this process can be compared with the burnout of paint on a car. However, if the sheet is replaced, a difference in hue may be noticeable. Even buying a sheet "just in case" will not save the situation.

Glossy or matte corrugated board is another point that determines appearance fence. The matte surface looks more noble, but it loses its attractiveness after rain, because. dirt from the soil settles on the surface of the fence. It is advisable to put such sheets on the foundation or constantly clean them. The point is not the attractiveness of the fence, but the fact that small particles of dirt increase the rate of destruction of the sheet coating.

To choose the right profiled sheet for the fence, you need to pay attention to a few more nuances:

sheet appearance. Large deviations in width, length (over the allowable GOST 19904-90) should alert you when buying (non-standard);

front surface quality. Peeling paint, blisters, stretch marks, scratches - all this will lead to the destruction of the surface and inevitable corrosion. Dents do not cause much harm to the profiled sheet, but they do not decorate the appearance of the fence;

cut quality. Usually the length of the sheet is set at the profiling stage. The guillotine cuts the metal sheet evenly, without notches. Using a grinder or other cutting tools gives an uneven cut - this is a direct road to rust at the cut;

covering wave geometry. It should ideally fit on the wave of the previous sheet. You do not need to believe the seller's statements that the sheet will be pressed with an additional self-tapping screw. The sheet screwed to the sheet, and not to the frame, will not hold the self-tapping screw, and installing additional support or lag is costly;

the presence of a film. It is not a mandatory attribute, but it will protect the sheet from damage during transportation;

Advice. After the installation of the corrugated board, the film must be removed. After it dries to the surface, the film is almost impossible to remove.

availability of a guarantee and other supporting documents.

Note. If the calculation of the amount of corrugated board is performed by the seller, he must provide the layout of the sheets. This is especially important when roofing works ah, as well as during the construction of a fence of complex configuration.

Considering these factors will help right choice fence corrugated board and avoid the situation shown in the photo.

Agree, a convincing example of why you should not save on the purchase of profiled flooring.

The material was prepared for the site www.site

How to choose the right corrugated board for the fence - video

The price of corrugated board for the fence

Based on the foregoing, we can conclude that the price of corrugated board is an objective value, which is determined by the thickness, type of coating and quality of the finish layer of the sheet. Decking, the cost of which is below the market, by definition, cannot be of high quality.

Advantages of a fence from a professional flooring

strength;
maintainability;
almost any form;
relatively low cost;
resistance to bad weather and mechanical damage;
beautiful appearance and the possibility of combining with other materials (combines well with stone).

In addition, it is possible from corrugated board, since it is not demanding in installation and maintenance.

Decking is considered wear-resistant and practical. Professionals in the field of construction, design and architecture have long used it in their projects. It gained considerable popularity due to its lightness, ease of installation, transportation, beautiful design and the main advantage - the price category.

Often profiled sheets are used for the construction of fences and roofing. Today it is presented in a wide range and in order to answer the question of how to choose a corrugated board for a fence, and what it is like, you need to have an idea about its varieties, standards, parameters.

Varieties of corrugated board

Decking is a thin sheet of steel that has four stages of processing (priming, passaging, galvanizing, polymer coating). Its manufacture is carried out on roll forming machines, as a result of which the surface of the material becomes wavy.

Waves are necessary for the rigidity of the sheet to give it strength.
Mechanicalthe properties of the profiled sheet depend on the wave width of the profile itself. This is important to consider when choosing.
According to the shape of the profile, corrugated board is divided into types:

Bearing (denoted by marking H) - used for roofing.
Wall (marking C) - for fences.
Universal type (NA marking).

There is also a specific standard for metal profiled sheet to designate its width and thickness. For example, C20-1150-0.8 (profile wave height 20 mm, width 1150 mm, thickness 0.8 mm). Standard thicknesses from 0.4 - 0.8 mm.

Advice! Existsa number of features in the marking and blindly trusting what is written is not necessary. For example, the designation C21 - sheets have greater rigidity, but a small width, unlike sheets C8. In other words, for fencing, C8 sheets need to be purchased less, however, C21 will be better in strength and more attractive in design.

A fence from such material can be made of any configuration, parameters, with any design solution, as profiled sheets have significant plasticity properties, have a wide choice of colors.

Selection by optimal quality and price characteristics

When choosing a profiled sheet, you need to consider how and in what area it will be used. For example, should the corrugated board withstand a certain weight, have significant tightness, withstand frost or heat.

If the region is not characterized by strong wind currents, models C8, 10, 20 are used. The fence made of profiled sheet will be durable and have a beautiful appearance. Such a fence will protect the site from the intrusion of thieves, from the wind, and provide good insulation from street noise.

A sheet of a low price category is made from galvanization. It is resistant to corrosion, has a service life of up to fifteen years. However, there are more modern views corrugated board, having a polymer coating, which performs the functions of protection and decoration at the same time.

The sheet can be dyed during production both on one side and on both sides. Most buyers opt for the double-sided option, which is great for any yard landscape design. The material goes well with concrete, stone, wood, brick.

Painting not only ennobles the appearance, but also protects against corrosion. The strict silhouette of a profiled sheet fence looks elegant, in the style of modern trends.

Types of material coating

In addition, such a fence will please its owners for about 50 years and the price will not be as expensive as a cheap option.
The profiled sheet is divided into types according to the coating:

polymeric - galvanized sheet is coated with synthetic type resin or polymer. The polymer has significant insulation. It may be painted in different colors at the manufacturing stage;
plastisol is a powerful defense. It is applied with a layer of 176 - 221 microns. It will protect you from negative influences. environment from mechanical damage. However, a profiled sheet with such a coating has high cost, but pays off by increasing the service life of the material;
polyurethane and polyamide paint;
PVDF.

Coatings vary in cost and properties. It is better to choose what material to make a fence from based on the conditions under which it will be operated. For example, for those who live near the coast, it is better to use corrugated board painted with PVDF paint. It will provide resistance to sunlight.

Coating with plastisol, PVDF and pural will significantly increase the cost of a profiled sheet, in contrast to a sheet coated with polyester.

The protective layer of zinc is optimal in terms of cost and durability. Aluzinc is better − upper layer from zinc 46%, aluminum 54%, silicon 1.6%.

Aesthetic aspects when choosing a material

Not so long ago, a company from Korea introduced a new technological line that allows applying various decors to profile sheets. This innovation is called photo offset printing.

Thus, it became possible to imitate wood, brick or natural stone. This is an excellent solution for connoisseurs of natural textures. In addition, such a profiled sheet can be ideal solution for a fence where there is a log house or it is decorated with stone.

The construction market has replenished with a novelty - a picket fence made of a profiled metal sheet. Certain models are produced with a pointed upper edge in order to use them specifically for building a fence. A metal fence is made from separate parts that imitate a wooden fence.

Easy installation of corrugated fence

Installation of a profiled metal sheet fence will take only two days. For it, it will be necessary to mark the boundaries of the fence, strengthen the supports, fix the beams as transverse fasteners and install the corrugated board itself.

The fence can be created in different heights. The maximum length of the sheet is 12 m. At a cost, it will come out much cheaper than alternative sheet materials, and at the same time it will be distinguished by high quality and wear resistance.
The material does not need additional staining over time, it is easy to clean with water from a hose.

Before buying, it is better to make sure that the material is made in accordance with the standards, its quality is confirmed by certificates, inspect the profiled sheet for damage, and pay attention to its integrity. The surface must be smooth and uniform in color.

The thickness of the sheet for the fence is enough 0.4 - 0.8 mm. You should not choose cheap material, as it is short-lived. It is necessary to find a balance between optimal quality and price.
The edges of the material must be smooth - without roughness, various kinds and defects.

The abundance of building material has led to the fact that even the construction of a high-quality fence is impossible without assessing all the characteristics of a profiled sheet, corrugated board and other sheet material for work.

Types of profiled sheet

Under the profile sheet is meant a material intended for cladding, roofing and other construction needs. Without it, you can’t build external fences and roofs.

The classification of the profiled sheet is the difference in thickness, height of the stiffeners and the difference between them.

But the types of profiled sheets are better described in more detail:

Scope (facades, fences, walls, roofing or supporting structure);
Corrugation (wave or trapezoid);
Corrugation height. There are also limitations here. Stiffeners up to 21 mm are for walls, up to 44 mm are fences, gates. A corrugation of more than 5 cm goes to those parts of the structures where there will definitely be a load on the material. Eg, fixed formwork, various building floors, roofing and other types of construction.
Profile width;
The thickness of the sheet itself;
Full and useful sheet width.

Profiled sheets are also distinguished by coatings, because “bare steel” must be protected with polymers or paint, or rather:

acrylic coating;
polyester;
Plastisol (polyvinyl chloride);
Polyvinylidene fluoride;
Polyurethane.

Is there a difference between corrugated board and corrugated board

There is a difference - this is the purpose of universal sheet iron. The above views are created for a specific task. If in detail, then the profiled sheet is taken during construction:

Fence;
Walls;
Roofs;
Some overlaps.

The material is almost the same, but!

Naturally, for each of the works it is sorted according to its characteristics, which is what makes it different.

Let's take an example. For the construction of the fence, you will need a profile sheet with the “smallest” wave (up to 21 mm), because the load on the material is not expected in the future (or used galvanized C 10). But roof view also suitable for this job, however, it is more expensive due to the rigidity characteristics.

We come to the conclusion: corrugated board is a material for roofing and for those construction sites where a load is provided. A profiled sheet is a sheet of iron with a weak rib, invented specifically for arranging fences and house cladding. That is the difference.

comparison table

Now, when buying a profiled sheet, they are guided by two proposed types:

Wall;
Roofing.

But the "fence" version of the material is better to choose according to the following criteria:

Operational nuances. It is always necessary to take into account the option of fastening the material, its type of installation (vertically or horizontally). If there are additional crossbars for fasteners.
Thickness. A thin sheet on the total length of the fence with a large distance between the supports can bend, “make noise” during strong wind. The excess weight of profiled sheets is a load on the crossbars and poles. Sometimes it is precisely because of the ill-conceived mass that the finished fence is skewed.
The rigidity of the material. Without stiffeners, there will be no structural density. They are necessary even in those places where there will be no load on part of the fence.
External decor. These are aesthetic preferences of an individual nature. Can be selected by color or shade, focusing on the overall color scheme surrounding buildings. Sometimes, when choosing, those colors are chosen that do not “burn out” in the sun in a short time.
Zinc is cheaper. The galvanized surface of the sheet without a decorative component is an excellent option for a budget and high-quality fence for a long time. Such sheets do not give in to moisture, do not fade over time. And they always look neutral on the outside. What else is needed for an iron fence?
Learn more about galvanizing. Checking the galvanized or aluminum top layer is a must. The manufacturer always indicates this characteristic. For example, for a profiled sheet thickness of up to 0.5 mm, there should be a value of 200 g / m2. Galvanization above 200 g/m2 indicates best quality sheet. But when even the thinnest type of profile sheet has some 70-80 g / m2, then it is recommended to refuse to purchase, even if the material goes to partitions or simplest form fence.

Fences from a professional flooring and a professional leaf

Even without work experience, erecting a good fence from a profiled sheet or flooring with your own hands is a feasible task.

Important! When buying, we do not save on material, consumables and delivery. Otherwise, the service life will be halved.

IN installation work will need:

Decking or profiled sheet of the desired color. What thickness? 0.5 to 1.3 mm;
Pipe or profile for poles. Can be used as well. Profile of smaller diameter for log;
Solution: sand, cement (300-400), crushed stone;
Measuring tool: level, rope stretched along the horizon;
Welding;
Screwdriver (drill). If the fasteners cannot cope with the thickness of the iron, then holes are pre-drilled;
Fastener itself. Ideal: self-tapping screws desired length and rivets (installed with a slapper). It happens that sheets sometimes disappear from areas where there is no constant presence of the owner. Therefore, it will not be superfluous to equip the profiled sheet with rivets over the entire area. Yes, and this type of fastener is the most reliable.

Working moments

We mark the area, for example, in the country. This applies to gates, gates, poles and planned objects in the future. Advice! The distance between the posts is from 2 to 2.5 meters. No more!
We start with poles. It is best to buy a square profile of 50 mm more. But we also allow a round version of the pillar. Before installation in the ground and pouring, it is desirable to weld any type of pillar from above so that there is no accumulation of moisture.
The depth of the pit for supporting pillars is 1/3 of their length. It turns out that if the pillar is 3 meters, then the pit is 1 meter. This is the standard that has been proven over the years. It is better to dig holes as early as possible.
Fence posts poured into the soil are fixed with mortar. At this time, you need to do lags. Their fastening always begins with a plumb line.
We fasten the profile sheet to the frame. We start with self-tapping screws, where we take into account the distance (step) of no more than 50 cm. Moreover, the sheets need to be fastened together only with an overlap, leaving 10-15 cm for the next part of the fence. So general design will only get stronger.

Which fence is best

A steel sheet fence can be called the best if:

The construction was carried out with their own hands or under the guidance of the customer;
Desired sheet thickness. But what thickness of the profiled sheet for the fence to order? Not more than 1.3 mm.
Soil features are taken into account. Soft soil will definitely shrink in 2-3 years. In this situation, it is better to arrange a small strip foundation along the entire length for reliability;
We did not save on the professional sheet. was selected quality material with the required level of galvanization;
When paint sheets are selected for work, scratches are a matter of time. It is better to buy for such material aerosol with the same type of paint, and the original appearance is guaranteed for the entire service life.
There is a combination of or . Now professional sheet under a stone is on sale everywhere. Sometimes the front part of the fence, closer to the gate, is decorated with forged elements. It will look very expensive and rich. And in the neighborhood such a fence will be recognized as the best!

A fence made of corrugated board under a brick can be seen in the title photo.

Results

Which fence is better to put in a private house? One of best options- made of iron on a square profile with permanent fastening.

Modern corrugated board is deservedly considered one of the most convenient and durable building materials. Its qualities such as light weight, ease of installation and transportation, attractive appearance and, which is far from unimportant, low cost, have long been appreciated by both professional builders and architects, and most individual developers.

Most often, a metal profiled sheet in the development of individual and suburban areas is used as a roofing and material for fencing. In order to decide which corrugated board for the fence is better to choose, you need to understand what types of corrugated board are on the building materials market, and how they differ from each other.

Grades of corrugated board for the fence

A profiled metal sheet, as can be seen from its very name, is made from thin sheet steel by rolling it on special roll forming machines.

As a result of such processing, the original workpiece from a flat metal sheet acquires a wavy or corrugated surface. Each of the corrugations performs the function of a stiffener, which greatly increases the strength and bearing capacity of the metal sheet.

Accordingly, the larger the trapezium or profile wave, the better the mechanical characteristics of the corrugated board. Therefore, this is the first thing to consider when choosing a profile for a corrugated fence.

Depending on the shape of the profile, there are the following main types of profiled metal sheet:

Bearing corrugated board, marked with the letter H.
Wall, denoted by the letter C.
Universal profiled sheet, marked with the letters HC.

The corrugated board of the first group is used, most often, for installation roofing, the second group - for the installation of wall fences and fences.

In addition to the surface profile, various types of corrugated board differ from each other in the width of the sheet and the thickness of the metal of the original workpiece. In order to make it easier to understand all this diversity, the standard provides for a special marking of corrugated board for the fence.

So, for example, the brand of profiled sheet for the fence C20-1150 -0.8 is deciphered as follows: wall corrugated board with a profile trapezoid height of 20 mm, a useful sheet width of 1150 mm and a thickness of 0.8 mm.

Which profiled sheet for the fence is optimal in terms of price-quality ratio?

The choice of corrugated board for the fence is determined, first of all, by the conditions of its operation. Unlike the roof, the fence does not have to withstand the weight of the snow that has fallen in winter, and there are no high requirements for tightness. Therefore, the answer to the question: "Which profiled sheet is better for a fence?" - usually a profile with a low corrugation and a thickness of 0.5-0.7 mm. Most often, the choice falls on wall corrugated boards C8, C10 and C20. Exceptions are areas with very high wind loads.

For all its small thickness, the wall corrugated board is exactly what is needed for the fence. It is durable and reliable, and fences made of such a profile look light and elegant. The wall profiled sheet will reliably protect the site from foreign penetration, wind, dust and noise. After all, in addition to all other advantages, corrugated board has very good soundproofing characteristics.

When deciding which profiled sheet to choose for the fence, you need to ask the seller about such an important characteristic as its service life. Any modern profiled sheet has a protective anti-corrosion coating.

Types of profiled sheet for the fence: wall profile C20-1150-0.6. One of the best options

The most inexpensive corrugated board for fences is made of galvanized steel. It has a sufficiently high resistance to corrosion and its service life can reach 10-15 years. However, this option can hardly be called optimal - rather, the cheapest.

That is why now galvanized corrugated board is used less and less - it has been replaced by a much more durable profiled sheet with a polymeric protective and decorative coating.

The best professional flooring for the fence - a profile with a color polymer coated

In addition to the fact that polymer painting serves as an additional protection against corrosion and mechanical stress for the profiled sheet, such corrugated board looks very aesthetically pleasing. Impeccably strict lines of the corrugated fence look elegant and modern. In this case, a colored polymer coating can be applied both on the front side and on both sides of the profile. In the second case, the fence will look the same from both the inside and the outside.

Therefore, many owners of individual plots prefer to choose double-sided corrugated board for the fence. Both sides fit perfectly into landscape design plot, turning the fence into an important architectural element of the entire development. At the same time, such a fence not only looks many times better than simple galvanization, but also lasts several times longer - up to 45 years, and costs not much more.

Which corrugated board is better for a fence based on the criterion of durability?

The most inexpensive and least durable is zinc sheeting. More reliable is the "aluzinc" coating, consisting of 45% zinc, 55% aluminum and 1.6% silicon.

However, most developers, when choosing which profiled sheet to make a fence from, prefer a profiled sheet with a colored polymer coating, which is applied for additional protection of the profile over a layer of zinc or aluzinc.

There are several types of polymer coatings for corrugated board:

polyester paint (such a coating is called polyester);
plastisol (a mixture of polyvinyl chloride and various plasticizers);
polyurethane-polyamide paint (the so-called "pural");
polyvinyl difluoride-acrylic paint (PVDF).

All polymer coatings differ from each other in their properties and cost. Therefore, which corrugated board to use for the fence must be decided depending on the operating conditions of the fence. So, for example, corrugated board painted with polyvinyl difluoride-acrylic paint is well suited for residents of the coasts of the southern seas. This coating is exceptionally resistant to ultraviolet radiation and aerosols of aggressive chemicals.

At the same time, when deciding which brand of corrugated board is best suited for the fence, one should not forget that the corrugated board coated with plastisol, pural and PVDF is more expensive than similar corrugated board with polyester coloring.

What kind of corrugated board to choose for the fence from an aesthetic point of view?

Today, not only corrugated board with a colored polymer coating is presented on the building materials market. A few years ago, specialists from a South Korean company developed a technology for applying various images to the surface of a profiled sheet. For this, the method of photo offset printing is used.

Thanks to this technology, a metal profiled sheet has appeared that perfectly imitates the appearance of natural wood, as well as brickwork or natural stone. These colors are ideal for those who love natural textures. Moreover, such a profiled sheet is exactly what is needed for a fence if your house is made of logs or finished with stone or boards.

In addition to a colored profile with a polymeric protective coating imitating natural wood, stone or brickwork, manufacturers of profiled metal sheets may offer other options. Before choosing a profiled sheet for a fence, it is better to take an interest in the existing novelties on the market, since the number of varieties of this material is increasing every year. These can be both new approaches to applying decorative and protective coatings, as well as constructive innovations and features.

In particular, not so long ago, a picket fence made of profiled metal sheet appeared on the market. Some types of corrugated board are specially produced with a pointed upper edge of the sheets for use specifically for the construction of fences.

Wherein metal fence it may even consist of individual elements that repeat the shape of a classic wooden fence.

Profiled sheet for the fence: which one to choose and why

Summing up, we can briefly formulate the main approaches to what a corrugated fence is and how to choose it so that the fencing of your site is reliable, outwardly attractive and harmoniously fits into the style and concept of the entire building.

First check the quality and thickness of the profiled sheet. Remember that a profile with a thickness of 0.5 - 0.7 mm is quite enough for a fence device.
Make sure that the corrugated board is made in accordance with all specifications and standards, has all the necessary manufacturer's certificates confirming its quality.
Remember that the wall profiled sheet has a large usable area and is cheaper than the bearing corrugated board. If your region is not characterized by increased wind loads, the use of a wall profile will fully satisfy all the requirements for the quality and strength of the fence.
Do not forget that choosing the cheapest option - you will definitely lose in durability. Try to find a balance between your costs and the protection of the material from the harmful effects of the environment.
And, of course, do not forget about the aesthetic side of the issue - try to familiarize yourself with all the texture and design options before making your choice.

The use of a profiled metal sheet for fencing suburban areas and frequent houses is widespread due to its light weight, ease of installation and transportation, and low material cost. Fences from a professional flooring are perfectly combined with any landscape, have attractive appearance.

To make the right choice of corrugated board for the fence, you need to have an idea of what types of this material are on sale, and how they differ from each other.

Profiled metal sheet is made from thin sheet steel by cold rolling through a roll forming machine. At the exit, a thin sheet acquires a corrugated surface in the form of a wave or a trapezoid.

The presence of corrugations increases the strength of steel and its ability to withstand large bearing loads. Depending on the purpose, the following main types of corrugated board are distinguished:

Type "H" - bearing, used for flooring.
Type "C" - wall, designed for the installation of wall fences.
Type "NS" - universal, used for flooring and for wall fencing.

For fences, corrugated types "C" and "NS" are suitable. Type "H" is used for roofing.

Another important characteristic of corrugated board is the height of the profile. This is the vertical distance between two adjacent corrugations (more simply - the height of the corrugation), which has a value ranging from 15 to 130 mm. In addition, the material different type differs in thickness metal billet and sheet width.

In order not to get confused in a wide variety of characteristics, there is a special marking for corrugated board various types. For example, the code C18-1150-12000 means: "Wall decking with a profile height (corrugations) of 18 mm, a sheet width of 1150 mm, a sheet length of 12,000 mm."

For fences, corrugated board grades C8, C10, C18, C20, C21, HC44 are used. The latter profile is used for the construction of very strong fences located in places with a high wind load.

The greater the profile height, the stronger the material. The usual corrugated board used for the fence has a C8-C21 profile with a sheet thickness of 0.4-0.8 mm.

This is quite enough to withstand the loads from atmospheric influences in conditions middle lane Russia.

Protective coatings

To increase the service life, increase the strength and anti-corrosion properties, a protective coating is applied to the profiled sheets. There are several types of coatings:

Zinc. This is the cheapest protection option. Galvanized corrugated sheets for fences have good resistance to corrosion, their service life is about 10 years. The thicker the zinc layer, the more durable the material. A high-quality galvanized profiled sheet is covered with a protective layer with a zinc content of at least 140g/m2.
Aluzinc coating - an alloy of aluminum and zinc, with the addition of silicon. Such a coating is stronger and more durable than zinc, but it is more expensive.
Lacquer. A layer of paint or varnish creates a protective film on galvanized sheets that prevents corrosion and improves the appearance of products. The downside is that the paintwork is poorly resistant to mechanical stress and is easily scratched.
Polymer. Fences made of corrugated board with a polymer coating meet all the requirements of strength, durability, resistance to corrosion and weathering.

Polymer coatings serve not only as protection, but also significantly increase the aesthetic qualities of the profiled sheet due to a wide range of color solutions. The fence with a double-sided polymer coating will perfectly fit into any landscape of the site. Therefore, private developers are increasingly choosing corrugated board for modern polymer-coated fences.

Polymer coatings differ in composition, color range and standard thickness of the applied layer:

Polyester. Considered budget material, standard thickness applying glossy polyester - 25 microns, matte - 35 microns.
Plastisol (PVC). It is a plasticized polyvinyl chloride, resistant to mechanical and atmospheric influences. The thickness of the application layer is 200 microns.
Pural (PRIZMA). new material based on polyurethane with additions of polyamide and acrylic, resistant to aggressive environments and ultraviolet radiation. Layer thickness - 50 microns.
PVDF (PVDF). Polyvinyl difluoride with the addition of acrylic, ideal for corrugated boarding for fences in the southern regions and on the coast of the seas. Not afraid of sea water chemical compounds, sharp temperature fluctuations, does not fade under the sun. Application layer - from 20 to 40 microns.
PRINT (PRINTECH). Modern coating applied by offset printing on a layer of polyester or PVDF. It has unique decorative properties, imitates the texture of wood, brick, stone. The original fence made of such a professional flooring looks stylish and unusual. Layer thickness - 35 microns.

The industry does not stand still, so when choosing a corrugated board suitable for a fence, you should ask the seller what modern coatings for profiled sheets are on sale.

How to choose corrugated board for the fence

Before buying a profiled sheet, you should evaluate the conditions in which the fence will be used. If you need to put up a temporary fence or hedge for outbuildings, then a simple galvanized material will do. It is better to choose the professional flooring necessary for a fence of constant operation with a polymeric covering.

When deciding which corrugated board is suitable for the fence, we must not forget that the material must match the overall design of the house.

For example, if the house is wooden, then PRINTECH coated corrugated fence, stylized as a tree, would be an excellent choice.

Now a picket fence made of profiled sheet with a polymer coating has appeared on the construction market. It consists of individual panels that follow the shape of a classic wooden fence. Such a fence will decorate Vacation home built in country style.

It is better to protect a summer house on the coast with a fence made of profiled sheet with PVDF coating, which will withstand the impact of salty sea wind.

There are many options, but the financial component should also be taken into account. It is not necessary to purchase expensive material, with a competent approach, you can choose an inexpensive corrugated board that meets all the requirements of long-term operation.

Offers from Moskomplekt

Our company has been operating in the construction market for over 7 years. During this time, relationships have been established with trusted suppliers of construction and finishing materials. We offer a wide range of corrugated board for the fence, High Quality and at moderate prices.

If you are in doubt about the choice of material, our experts will select the products that meet your requirements. At your request, we will not only deliver the material to the site, but also install the fence in accordance with the norms and rules of the construction industry.

Approximate prices are given in the table. The price may vary depending on the volume of the lot of purchased material.

Prices for fences from corrugated board

Fence from galvanized corrugated board on 2 metal logs: Pillars 60 * 60:

	The cost of p.m.
Height	Sheet thickness 0.4 mm	Sheet thickness 0.5 mm
	850 rub.	900 rub.
	900 rub.	980 rub.
	940 rub.	1000 rub.
	1000 rub.	1050 rub.

Corrugated fence coated on one side any color on 2 metal lags: Pillars 60*60

Corrugated fence coated on both sides 2 metal joists: Posts 60*60 (RAL 3005, 6005, 8017)

Prices are subject to change due to ongoing promotions and market volatility.