How to make wooden sliding boards with polycarbonate. How to make polycarbonate doors: a master class. Types subdivided according to design features

Modern materials make it easy to make sliding doors with your own hands. This is much more profitable than buying ready-made ones, which in most cases have high cost. At self-manufacturing it is possible to make a design of a non-standard size for any doorway, it is possible from ordinary room make several separate zones, a sliding partition can separate the dressing room, highlight a small balcony greenhouse, and so on.

Sliding doors have many advantages:

significant space savings due to movement not inside the room, but along the wall.
very easy installation,
they do not open with a stream of air, a draft,
a wide range of materials used for the manufacture,
sliding doors can be made by yourself.

What kind of sliding door can you make with your own hands

There are several types of sliding doors, but if there is no experience, you should start with the simplest - a compartment mechanism, when it consists of one part and moves to the side, or two parts and moves apart on both sides. Having learned enough, you can try to make cascading or radius structures with your own hands. The principle of operation is that the door leaf, mounted on rollers, slides smoothly along the wall along the guides.

The material from which the fabric of the product can be made is:

tree,
glass,
polycarbonate.

The most practical and unpretentious are sliding interior doors made of polycarbonate. Polycarbonate is a lightweight and reliable material that is suitable for any application, is not fragile and completely safe, even when cracked, it does not produce sharp fragments. It does not deform from moisture, does not burn, has a wide variety of colors and levels of transparency, is slightly scratched and is very easy to clean. Installing a new or replacing an ordinary door with a polycarbonate sliding door will make the interior attractive and extraordinary.

Do-it-yourself interior doors made of polycarbonate can be frame and frameless.

Frame - involve the placement of small fragments of polycarbonate in a special frame, the advantage is low cost. The frame can be made of plastic, metal, wood.
Frameless will cost more, but also look more dignified. Made from whole piece polycarbonate. They will give the whole room mystery and elegance.

To make polycarbonate sliding doors with your own hands, you can look at examples from the catalogs posted on manufacturers' websites. Approximately choosing a model, you need to buy necessary materials and proceed directly to production. You will need this tool:

roulette,
level,
screwdriver or screwdriver
drill,
jigsaw, manual or electric,
self-tapping screws, bolts.
construction corner.

Required material:

polycarbonate,
guide profiles,
roller carriages,
accessories.

How to make a do-it-yourself polycarbonate sliding door

In order to make sliding interior doors yourself, you need quite a bit:

Place the canvas in the frame, if the design does not imply this, the first stage is skipped.
Attach guides.
Install the finished product.
Hang accessories.

Door leaf preparation

First of all, you need to measure the doorway where it will be directly installed. The second stage is the assembly of the frame - it should be slightly smaller than the opening, so its size should be reduced by 1-1.5 mm on each side. The prepared frame, using a construction square, is measured for a clear squareness of the structure in order to prevent distortion and only then is fastened. Fragments of polycarbonate are attached to the frame with self-tapping screws or decorative fasteners. The frame can be made with your own hands, both from new materials and cut out from an ordinary old door.

When making a frameless structure, the process is even simpler. The polycarbonate sheet is cut old door or clearly according to the size of the doorway.

Mounting guides

There are two types of guide systems - steel and aluminum. Steel is stronger, can withstand heavy loads, but is noisier and looks rougher. Aluminum - looks more aesthetically pleasing, the rollers move silently in it, but it is not so durable. The choice is yours, and do not forget that 50% of the smoothness and softness of movement depends on the correct installation.

Interroom doors move on two guides - top and bottom. There is also another type of construction - hinged, where the guide is attached to the ceiling or the top of the wall, and the canvases are suspended by rollers.

The length of the guide profiles should be twice the width of the door leaf.

Guide profiles are attached to the floor, ceiling or wall. The main condition is to set them absolutely evenly, otherwise the polycarbonate door will open or close on its own. This must be done using a long level. Another point is to clearly mark the vector of movement in space. With the help of a tape measure, it is worth making marks on the floor and ceiling, carefully measure everything, and only then screw it on.

Door leaf installation

Depending on the size, you need to choose the number of roller mechanisms. If the canvas is rather narrow, two are enough - upper and lower. For normal widths, two at the bottom, two at the top should be used. With a hinged system, at least two must be used.

The order is as follows:

a fixing bolt is inserted inside the roller carriage,
the roller mechanism is inserted into the guide,
on top of the polycarbonate door, brackets for roller carriages should be installed, stepping back from the edge of 4-5 mm.
directly installed sliding door on rollers. First, into the brackets at the top, then into the bottom ones and the bolts are screwed. Without experience, it is quite difficult to do it yourself, outside help will not hurt. If necessary, adjustment is made, this can be done by tightening the bolts.

There is also a second way:

the rollers are immediately screwed on top and bottom,
the upper part is inserted into the guides,
slightly lifting the door, you need to insert it into the lower profile.

The option is selected based on the features of the roller mechanism. You can check the quality of the installation by driving right and left several times. If there is no noise, jerks, the design does not cling to anything, it walks softly and smoothly, then everything is done correctly.

After the completion of the installation work, stoppers are installed along the edges, then handles, decorative strips, locks and other door fittings. If desired, you can replace ordinary interior doors with polycarbonate sliding doors with your own hands, thereby winning the opening radius area. To do this, just like that, you need to replace the canvas and install the guides.

More recently, such a word as polycarbonate was associated by many with a cottage, or a private house. This is because even in the days of the Soviet Union, polycarbonate was used only for growing crops in greenhouses. Products of this type were only in the form of thermal structures for plants. They were only in the dachas, but not many could afford them, expensive. Most of our population, for lack of the opportunity to purchase polycarbonate, made greenhouses with their own hands from everything that came across. From wooden products to metallic.

In modern times, a polycarbonate greenhouse is widespread, but this is not the only purpose of this building material. Today you can see, among other things, commercial pavilions made of polycarbonate, and gazebos, as well as road transport.

The material is very light. Any products made of polycarbonate are lightweight when compared with analogues made of plastic, or metal.
In terms of strength, the material also wins. For this reason, even showers have polycarbonate elements. For example walls and doors.
High fire resistance parameter. For example, if a polycarbonate product is engulfed in flames, then it will quickly come to naught, because there is nothing to burn in polycarbonate. There will be no bad results.
The material is practical to use. For example, the doors from our hero are simply cleaned with standard cleaners. detergents for dishes.
Longevity. Having put a door from this building material, you can forget about their change for decades, even if they become morally obsolete.
Exposure before temperature changes. Even though the most popular today are interior doors made of polycarbonate, the door at the entrance will serve no worse, and even more so, for a very long period of time.

If you plan to make polycarbonate doors with your own hands, you need to parse certain of their data. From the above it follows that the doors are divided into the following categories:

Interior doors. We install them directly indoors in order to separate one room from another.

Mounted. Mounted in the existing frame in the opening.

Sliding type. They should be mounted on a special guide, such a door will open along the wall, as if entering it. These doors are much stronger. For this reason, it makes sense to install such doors in the nursery, because they have a high degree of security.

Types subdivided according to design features

Frame type doors. They look like a special frame in which polycarbonate is fixed. The material from which the frame is made can be absolutely any. From wood to plastic and metals. Doors of this type can be easily found in commercial premises, and production sites. They are quite cheap.

Frameless door type. This, without a twinge of conscience, can be said to be an elite type of door. Outwardly, they are very different from all of the above. If you want to make such a door with your own hands using polycarbonate, you will need to familiarize yourself with examples of these doors from the catalogs. The shape of this type of door adheres to certain conditions, it is elegant and discreet in design. Frames for the installation of such doors are not needed, because they are made from whole fragments of polycarbonate.

Types subdivided according to design features

Tools

The production of polycarbonate doors does not require any significant experience in this area, but care must be taken, paying close attention to various details. Since polycarbonate products are processed very simply, the tools necessary for this type of work have a small list.

Necessary tools for making a door

hand saw;
hacksaw;
circular saw;
jigsaw;
manual drill, electric type is also suitable;
drills of the required size;
machines that make it possible to cut at an angle;
awl;
hammer;
measuring instruments (ruler, goniometer, level, triangle, each, preferably from 20 cm or more);
fasteners and fasteners.

Additional building materials for a frame type door

self-tapping screws;
bars;
corner made of metal or plastic;
polycarbonate sheet;
canopy.

Additional building material required for the manufacture of sliding doors

Fittings to install a sliding door,
guide mechanism (usually a metal tube) with anchors;
fasteners;
polycarbonate sheets;
door knob.

Installation of a hinged polycarbonate door

If you intend to install a frameless door, you will need:

Accurately and accurately find out the dimensions of the opening, record the parameters obtained. Right angles will require the most attention, because it is they, if the measurement was not correct, that will give you problems with skew.

It is necessary to tighten the corners with the help of corners, so as not to collide with a warp for sure. The door is installed with a canopy.

Take a measurement of the opening and directly the door that was in this opening.
Measuring the doorway
Grinding of the frame surface, both internal and external, is required.
It is necessary to process the frame with varnish or paint. We advise you to paint with a stain, or a polishing agent, so the frame will look more beautiful.
Now you need to sheathe the frame directly with polycarbonate. We connect the sheets according to the principle below.
Installation of polycarbonate through a connecting profile
It is necessary to fix the canopies and finish the work.

Installation of a polycarbonate sliding door

The design of this type is different due to the guide, with its help you will be able to use the door not as usual, but parallel to the wall, which many people associate with science fiction films of the last century. This option will save used space in the house. If you prefer a model with a single sash that perfectly blocks drafts, then, as a bonus, at the same time warm the room.

Installation of sliding door mechanisms

It is necessary to fix the guide above the doorway, the standard is 5-10cm.
Fix the rings in the polycarbonate sheets.
Then, it is necessary to attach the entire structure to the guide.
Bottom line: the assembly of polycarbonate doors, whatever type you prefer, is carried out by a very simple method. It all depends on the size of your own desire.

Installation of sliding door mechanisms

A large selection of colors and ease of processing have long opened wide opportunities for its use in interior design. Polycarbonate it is used for the device of interroom, screens for zoning of internal space and details of furniture.

Polycarbonate doors have become very popular lately. The door leaf made of synthetic polymer has the following characteristics:

extraordinary lightness. Thanks to this, the installation process of structures becomes convenient and simple;
synthetic polymer is very durable, which affects both the ease of installation door structure, and on the convenience of its further operation;
high degree of security. Even in case of damage, polycarbonate does not form traumatic fragments and does not crumble like glass;
wide range of design possibilities. Depending on the type of polycarbonate, the doors can be completely or partially transparent, have different colors and shades. If necessary, you can choose a matte version of the material.

Types of polycarbonate doors

According to the method of operation of the opening mechanism, the design of doors made of synthetic polymer can be hinged and sliding. The hinged structure provides for fastening the door leaf to the jamb with the help of canopies. Sliding doors open and close parallel to the wall plane using a special guide mechanism.

Doors made of polymeric material can be frame and frameless.

The variant with a frame assumes the presence of a frame for glazing from. The frame can be metal, plastic or wood. The frame should ensure the rigidity of the door structure, but at the same time be as light as possible. Frames made of aluminum profiles are well combined with polycarbonate.

Frameless design, respectively, has no frame. In this case, all hinged elements and fittings are attached directly to the polymer sheet. To ensure rigidity and give the structure the necessary weight, for the construction of frameless doors, as a rule, monolithic polycarbonate is used. This door design looks strict and solid, but it also costs more.

Making your own polycarbonate doors

In order to make polycarbonate doors with your own hands is not required great experience carpentry work. Since polycarbonate is a material that is easy, the performer will only need to carefully and accurately follow a sequence of simple steps.

Assembly and installation of a hinged door

The manufacture of a hinged door begins with the definition exact dimensions designs. If a polycarbonate door is planned to be installed to replace the old door, then the task is simplified, since the old door will serve as a pattern for making a new one. If the door is installed for the first time, then first careful measurements must be made opening. It must be remembered that the dimensions of the door must be 1-2 mm smaller than the dimensions of the opening to ensure the process of opening and closing.

After determining the dimensions, you can begin to manufacture the frame of the door structure. When assembling the support frame, it is necessary to strictly maintain right angles in order to avoid warping and jamming of the door during further operation.

If the frame is wooden, the required rigidity can be achieved by tightening the corners of the structure with special metal corners. When the assembly of the frame is completed, its surface must be carefully polished, painted or coated with a colorless varnish.

Polycarbonate can be attached to the frame either on both sides, or in one layer in the center. Double-sided fastening will give the door more rigidity, but the material installed in the center of the frame will look much more refined.

For fixing polycarbonate in one layer, it is better to use aluminum as a frame. After installing the polymer material, it is necessary to attach awnings, handles and a lock. The process of installing the door on canopies is simple due to the fact that the polycarbonate door is very light in weight.

Sliding system

The design and installation of sliding doors, on the one hand, is a more complex and expensive process due to the fact that large quantity details and accessories. On the other hand, almost all the details of this system are included in the complete set, and the process itself is very technologically advanced and consists of several well-controlled stages.

The mechanism of sliding doors is completely identical to the mechanism of sliding wardrobe doors. The system consists of an upper guide that holds the door leaf in vertical position and the lower rail along which the door moves with the help of support rollers. In some designs of sliding systems, there is no lower rail, and the door leaf is suspended from the upper rail.

When installing sliding doors, special attention should be paid to the horizontal installation of the upper and lower guide systems, since the entire operation of the mechanism in the future depends on this.

Installation of fittings on the door leaf must be carried out in accordance with the instructions for the parts kit. Despite the fact that the composition of the kits may differ, in general they include: a roller spring system for fixing the door leaf in the upper rail, support rollers or wheels for installing the door on the lower rail, clamps and door stops.

After installing a polycarbonate sliding door in the guides, it is necessary to adjust the position of the door leaf. Adjustment is made special screws included in the design of the lower support rollers. By rotating the screws, it is necessary to eliminate all distortions of the door leaf and achieve its even location vertically and horizontally.

More recently, the main purpose of polycarbonate was the construction of country greenhouses, showers, the construction of canopies or canopies over the porch. But today this material is successfully used in the decoration of apartments. So, polycarbonate doors have become a successful design development, with which you can decorate not only garden buildings, but also urban premises.

Frame doors consist of wood, plastic or metal frame in which polycarbonate sheets are inserted.

A huge number of color options in which this product is produced construction material, allows you to make interior designs that are fully consistent with the style directions and shades of the apartment. And other advantages of do-it-yourself polycarbonate doors are obvious:

The material has a small mass, which makes the construction of it light and airy.
Polycarbonate elements are more reliable and safe than glass ones.
Even cracked, polycarbonate does not crumble into small fragments.
Care of elements from this material is very easy and simple.

Given all the above advantages of the material, it is possible to produce interior elements that are distinguished by a long service life and durability.

Features of polycarbonate door structures

Image 1. Scheme of a polycarbonate hinged door.

Today, 2 construction options have been developed interior structures from polycarbonate with their own hands. So, you can make doors hinged or sliding. Like conventional designs, hinged doors are traditional canvases installed using special fasteners on door frame. The variant of sliding elements is created on the principle of a compartment, where the doors open along the walls.

Both of them can be framed or frameless. To create frame elements, base frames are used in which polycarbonate sheets are installed. Such frames can be metal, plastic or wood. In the creation of frameless elements, no other material is used, except for polycarbonate. Doors made of solid canvas look very beautiful and rich, but you will have to spend a little more money on their arrangement than on creating a structure with a frame.

Algorithm of actions for the manufacture of hinged doors

Polycarbonate is a very easy material to process, so in order to make a polycarbonate door on your own, you will need very few tools. The minimum set consists of:

electric drills with drills;
screwdriver or screwdriver;
level;
measuring tape;
building square;
cutting machine or jigsaw.

For a frame door, you need to prepare:

a solid polycarbonate sheet or several pieces, corresponding in size to the size of the doorway;
a corner made of plastic or metal, a beam, the length of which is equal to the perimeter of the doorway;
self-tapping screws;
corners for fixing the sides of the frame;
fasteners for fastening the door structure to the frame.

For the manufacture of a frameless product, only fasteners and a polycarbonate sheet are required.

The algorithm of actions in the manufacture of polycarbonate elements with your own hands is quite simple, and a person with minimal carpentry skills can easily handle it. An example of a frame product is shown in the figure (image 1).

First of all, it is necessary to measure the opening where the structure will be hung. In accordance with the measurements, the frame is assembled. It should be borne in mind that the frame should be slightly smaller than the opening, so all sides of the frame and leaf should be reduced by 1-1.5 mm, which will allow the leaf to close firmly, but without touching the door frame.

When making a frame, it is necessary to carefully measure the squareness of the structure with a square, otherwise the door simply will not enter the opening. In order to connect the frame from a bar, you can use special metal corners. If the frame is assembled from plastic or metal materials, corners can be omitted. After Assembly wooden frame additional aesthetics should be given by sanding it well and covering it with stain or varnish.

Frameless doors are made from a single sheet of polycarbonate and are more expensive than framed doors.

You can also make a frame using the canvas of an old door. To do this, you need to put the bars around the perimeter of the canvas, give them the required dimensions with a jigsaw or machine, and assemble the frame. Then, a polycarbonate sheet is fixed onto the prepared frame using self-tapping screws and a screwdriver.

To make the polycarbonate door look more attractive, you can use self-tapping screws with decorative caps. Then, canopies are attached to the frame and box, on which the door will be installed. After that, you can mount the structure itself. Since polycarbonate is much lighter than ordinary doors, one person can successfully do this job.

In the manufacture of frameless doors, the algorithm of actions is even simpler. Here you just need to attach a sheet of material to the old door and cut the canvas to the desired size.

But it must be remembered that doors of this type require the use of very durable and reliable material, which is distinguished by both quality and a higher price.

Rules for the manufacture of sliding doors

To assemble a sliding product, you will need the following materials and tools:

a polycarbonate sheet with a height and width of 5-6 cm more than the dimensions of the doorway;
a metal tube to create a guide 2 times the width of the doorway;
fasteners;
anchors for fixing a metal tube;
set of materials above.

When a sliding structure is made, work begins with fixing the guide. In this case, the metal tube must be fixed at a height of 5 to 10 cm above the doorway. One half of the tube is located directly above the doorway, the second is shifted along the plane of the wall in the direction where the door should open.

Then rings are screwed onto the polycarbonate sheet with fasteners, with the help of which the sheet will move along the guide. The rings must be fastened in such a way that the door is 1-1.5 mm from the floor. If a threshold is set in the opening, then the canvas can be lowered just below it, which will create the possibility of a tighter closing of the opening.

Rings with polycarbonate are hung on a guide, at the ends of which it is necessary to install limiting elements. If necessary, handles are attached to the canvas. An elegant and secure door is ready!

Using polycarbonate to create interior doors by hand is the best option, in order to make your home more original and beautiful, without spending significant effort and money. These products will last long time, and if necessary, they can always be replaced with new ones.

Sliding doors with sashes made of glass are distinguished by a special aesthetics. In addition to the fact that sliding partitions allow rational use of space, transparent material gives the interior sophistication and lightness, and contributes to good illumination of the room. But the glass sheet has significant drawbacks: the high cost and fragility of the material, which requires a careful attitude to the design. The manufacture of glass panels can only be done by specialized companies that have the necessary equipment for glass processing.

A good alternative to natural glass are various polymer materials. One of the most popular transparent polymers, which is used for the manufacture and installation of transparent canvases for sliding structures, is polycarbonate. This material is impact-resistant, lighter than glass, has the same transparency, and most importantly, you can make polycarbonate sliding doors with your own hands.

Features and types of material

Polycarbonate is produced in a monolithic and cellular version. These materials have different aesthetic and specifications. Each type of polycarbonate is installed in a sliding structure of a certain type, which ultimately determines appearance finished sliding door and polycarbonate partition.

Important! The variety of polycarbonate sheets makes it possible to use it for the manufacture and installation of a sliding door, similar to natural glass, or use it as a decorative panel material. It can be used as independent material for the manufacture of door leaves, and in combination with other decorative materials(laminated chipboard, MDF).

Monolithic polycarbonate

It is a solid sheet of polymer with a smooth surface. It is a full-fledged analogue of natural glass.

They are produced by analogy with sheets of silicate glass with a material thickness of 2-12 mm. Thus, it is possible to produce either a frameless type panel with a thickness of 10 mm for mounting in a hinged structure for glass doors, or use them as inserts in a frame from a profile for sliding wardrobe systems.

Thick sheets of this material are highly durable and are also called anti-vandal. Not only are they resistant to impact, they cannot be broken even intentionally.

Cellular polycarbonate

This material is a hollow sheet, which consists of two or more thin layers connected by thin bridges. Produced by extrusion.

Due to the cellular structure, a door made of this material weighs more than ten times less than a glass door.

Due to the multi-layered material, it cannot be made as thin as monolithic polycarbonate. The thickness of the produced sheets starts from 4 mm. Panels with a thickness of 32 mm are made from cellular material.

Important! When planning the dimensions of a sliding door or a polycarbonate partition, you need to remember that the width of the strip of cellular material is 2.1 m, and it is cut along the length in stores in increments of 1 m. The length of the end profile for polycarbonate is associated with these dimensions.

Profiles for polycarbonate

For mounting and closing the edges of polycarbonate sheets, several types of profiles are produced. They are made from aluminum and polycarbonate. In the manufacture of a sliding door, only end profiles may be needed to frame the frame and create a rigid frame. It depends on the design of the door, the chosen type of sheet of material and the technical capabilities of the master in terms of the quality of cutting the material at home. Such a profile may be needed to stiffen the panel and to frame the door, which will hide the chips.

The end profile closes the honeycombs of the cellular sheet that are open at the ends from moisture and dust getting into them. If you do not close the ends with a profile, then over time the material will lose transparency. In particular, it is necessary to be conscientious about closing the ends of the polycarbonate when installing the door to the bathroom.

The end profile, which acts as a frame, will give the door an aesthetic and finished appearance.

Under any purchased sheet, there are also end profiles of the appropriate thickness: from 2 to 16 mm. The length of the profile is the same as the width of polycarbonate - 2.1 m.

How to work with polycarbonate

After buying cellular polycarbonate, you can see that its ends are sealed with tape. This is a temporary protection that needs to be removed. After cutting the polycarbonate, the ends with open cells will need to be glued with sealing tape. The end profile is put on over the tape. For holding aluminum or polycarbonate profile it is planted on small droplets of transparent silicone.

In addition to the ends, polycarbonate is pasted over with a film on one (front) side. It is removed only after the installation of the cellular polycarbonate sliding door is completed. The only thing that needs to be done is to partially unstick it around the edges, where the frame profile will sit, and the roller carriages will be attached. In addition, this will prevent the sides of the canvas from being confused if a sliding door of two or more wings is mounted.

Important! Before cellular polycarbonate is sealed and installed in the sliding door frame, it must be kept in a room with dry air. This will prevent the formation and accumulation of condensate inside the cells of the sheet.

To cut the material, a jigsaw with a fine-toothed saw, a grinder, and a clerical knife are used.

Frame panels

The polycarbonate structure with the frame will be more visible, it will be perceived as a full-fledged door. The frame will act as a frame that will stiffen the panel.

The compartment version is most suitable for the manufacture of a polycarbonate sliding door. Profile frame for sliding design compartment doors made of polycarbonate are assembled on self-tapping screws, there is no need to install additional fittings on the canvas. Polycarbonate 4 and 10 mm thick can be installed in the frame. Thin parts are installed in the profile using a special seal. In this option, you can make the canvas combined, with inserts from monolithic, cellular, transparent or colored polycarbonate.

Sliding mechanisms with frame canvases are supporting and hinged. Hinged systems are installed in the rooms, in which there is no bottom rail, and the door is held with U-shaped flags installed on the floor at the side of the opening.

In the support mechanisms, the canvas moves along the lower guides, and the upper roller serves to balance the sash. Support structures are installed in openings with low traffic.

Rollers in structures with a frame are attached to the upper and lower horizontal jumper of the frame frame. Each manufacturer produces its own range of profiles, which differ in shape, type of coating, but all standard sizes are the same.

Sliding mechanisms for frameless panels

Sliding systems designed for glass panels differ from the usual carriages by the mechanism of attachment to the canvas. They are designed for mounting sheets with a thickness of 8 to 12 mm. They have two types of fasteners: clamping and point-clamping. The principle of their work is as follows: two long strips wrap around the panel from the end on both sides and are clamped. In point-clamp systems, the screw that tightens the jaws of the clamp passes through the web, and a hole must be drilled for it. In clamping systems, the clamping jaws are applied to the end of the panel, and the clamping screw is located above the web.

Important! In these cases, an aluminum end profile must be installed on the canvas.

All designs with fastening of roller carriages to glass (polycarbonate) are only with the upper type of sliding. There are three main types:

Open;
Closed;
Mounted.

System open type It is a guide in the form of a pipe along which a roller in the form of a pulley rolls.

Closed structures usually have clamp-type roller carriages, and after installation, the upper guide is closed with a decorative strip.

In the hinged system, the roller carriage is mounted on the side of the panel, and the guide is not above the sash, but behind it.

Video how to cut polycarbonate:

IN sliding systems polycarbonate is a cheap and practical alternative to glass. But due to the flexibility of this material and the presence of chips after cutting, the sheets must have a frame made of a profile that will hide all defects and make the sash rigid.

In contact with

Comments

Roman 21.04.2019 03:43

Hello! I share the feelings of the previous speaker! I would like such doors. I am writing from Voronezh

Grade

New Articles

New comments

S.A.

Grade

Svetlana

Grade

Sergey

Grade

Sergey

Grade

Alexei