Liquid wallpaper as an apartment renovation. Liquid wallpaper: application technology. Advantages of liquid wallpaper

Until recently, rolled wallpaper was popular. Nobody heard about it. Excellent adhesion to the surface of the walls, even on curved sections, a wide range of colors, original design, lack of seams and joints - all this makes this material popular. What are they? How to finish the walls with this material, apply? Let's figure it out.

What is liquid wallpaper?

Preparation of the composition

Although instructions for preparing liquid material are always attached to the package with the composition, we will outline some features.

The composition should be prepared before starting work for 6-12 hours. You can purchase a composition where all the components are already mixed or all the components are placed separately in sachets.
If you purchased a composition with separately decomposed components, then first you need to mix everything well in a container, fluffing up.
If you want to add glitter and dyes separately, then they are first mixed with water, and then add the main mixture, so that then you get a uniform color and sparkles. For a high-quality coating, the finished mixture should not have lumps. From each package, the composition is prepared separately in a container, and then mixed. Mix better with hands. There are mixtures with fabric fibers that can be torn with a mixer.
The finished mixture is infused for a certain time to swell the adhesive composition, it is indicated in the instructions. And only after that, ready-made mixtures from different packages are mixed. The amount of the composition must be sufficient for application to the wall or to all surfaces. Different batches may vary in shades. The prepared solution does not lose its properties for a long time (up to two weeks).

Do-it-yourself liquid wallpaper application

The process is simple, reminiscent of puttying. A portion of the composition is applied to the wall with a spatula, trowel or float in a small layer of 2-3 mm. Sometimes the mixture won't stick to the wall because it's too thick, but the problem can be corrected by adding a little water. Grater put the mixture on the wall, twisting a little in different directions.

Plaster with liquid wallpaper at a temperature of more than 10 degrees when the room is ventilated. The composition dries from a day to three.

For more information on how to apply liquid wallpaper, read.

Coating care

Proper operation will help to use liquid wallpaper for up to 10 years. The maintenance of the coating is simple - it is enough to clean it periodically with a vacuum cleaner.

So, using, you can get excellent results in the design of arches, columns, walls or individual fragments of the interior. Happy repair.

Read on to create a unique design.

And about drawing liquid wallpaper The video will tell you more.

Video: how to apply liquid wallpaper on the walls

Share with your friends on social networks!

You can receive new articles by email. mail!

The site is non-commercial, developed at the personal expense of the author and your donations. You can help!

(Even a small amount, you can enter any)
(by card, from a cell phone, Yandex money - select the one you need)

Recently, one very interesting trend has emerged - more and more often, for wall decoration, they use not the usual standard factory-made wallpaper, with no color or relief pattern applied, but the so-called “liquid”, which are applied to the walls with spatulas, brushes, rollers, other painting and plastering tools. Ready-made mixtures for this technology can be purchased at hardware stores, but craftsmen have long decided on the recipe for this decorative coating walls, and with success it is used for the manufacture of the working mixture.

Do-it-yourself liquid wallpaper can be made from a variety of different materials, which are usually no longer useful on the farm - this feature can also be called positive quality similar finishing material. You do not have to spend money on expensive components of the composition, saving a certain amount of money, and in addition, to a certain extent, you can solve the problem of waste disposal.

Before proceeding to get acquainted with the process of making "liquid wallpaper", you need to thoroughly understand what they are.

What is "liquid wallpaper", their main properties

This finishing material is fundamentally different from all other types, since it almost entirely consists of natural, as they say, “breathable” materials. The basis of "liquid wallpaper" is cotton, cellulose or silk fibers. The component composition also includes a bonding agent (one or another glue), which, when mixed with water, creates a mass suitable for application to vertical walls, by analogy with .

Packages with "liquid wallpaper" in different colors

Ready-made factory mixes are usually sold in sealed plastic bags. Each package contains instructions for the preparation and application of liquid wallpaper.

The bags contain a dry composition, consisting of fibers treated with glue, and some plasticizing and modifying additives. "Liquid wallpaper" can be already painted in a certain shade, or have a neutral White color.

If it is planned to apply coatings of a certain tint to the walls, then white wallpapers are purchased, and then they are given the desired color or tint effect using special coloring additives, sold separately.

What specific advantages "can boast" of such a finishing material:

After applying to the wall, as it dries, the layer of "liquid wallpaper" acquires a porous structure, which contributes to additional sound and heat insulation of the walls of the room.
This decorative coating does not clog the pores in the wall material and allows them to "breathe", which helps to optimize the microclimate (temperature and humidity) in the room.
When mixing the solution and when using it and drying, the material does not emit any odors, therefore, when carrying out repairs in one room, there will be no particular discomfort in other rooms - you can not leave the apartment for this period.
The material has antistatic qualities, due to the fact that it consists of natural components that carry a neutral charge of electricity. This has a positive effect on the health of the residents of the house or apartment. In addition, due to the antistatic effect, this decorative coating does not attract dust masses to the surface of the walls. Dust particles will not accumulate either inside or on the surface of the material, which means that the air in the room will be cleaner.
"Liquid wallpaper" are fireproof. The materials from which they are made do not contribute to the spread of fire, self-extinguish and do not emit substances toxic to the human body. .
This coating, despite the presence of organic fibers in its composition, does not absorb odors, due to the presence of an adhesive mass, which becomes a kind of protective film for the remaining components.
"Liquid wallpaper" have the ability to retain the original color for many years, as they are little affected by ultraviolet radiation .
In addition to all the above, this coating has no seams and can be laid with a thickness of 1 to 8 mm. Usually it is applied with a thickness of 2 ÷ 5 mm.
Under this material, you do not need to carefully prepare the walls, as it will itself help to level them, visually masking all surface flaws.
On the wall, after drying, "liquid wallpaper" creates a pleasant to the touch, soft, rough surface.
The coating well masks various wall defects, such as small cracks or crevices - “liquid wallpaper” fits well near frames and baseboards, and their excess, which extends beyond the corners, is easily cut off. At the inner corners, the applied layer does not wrinkle or crack when the walls of the building shrink, unlike paper wallpaper.
If it is necessary to carry out certain works in the room with “liquid wallpaper” related to the violation of the integrity of the wall, the decorative layer is removed with a spatula in the desired area, the cleaned mass is preserved. The wall is ditched or drilled, then sealed, and the previously removed mixture of wallpaper, previously diluted with water, is applied back on top.
If desired, on top of the old liquid wallpaper, you can put a layer of new ones that have a different color. In addition, if necessary, the material can be easily removed with a spatula.
By adding various dyes to the mass, on the wall, using different spatulas, you can create numerous color or even relief drawings or panels that create an accent for the interior design of the room.

Bright panel of "liquid wallpaper"

The material is fully suitable for premises intended for housing and household needs, as well as for offices and halls of public buildings.

"Liquid wallpaper" can be diluted from the purchased mixture, or you can cook it completely on your own, using suitable materials found at home as the necessary components.

Ready mixes

In order to dilute the "liquid wallpaper" from the factory mixture purchased at the hardware store, you need to prepare one or more containers for soaking. Usually, a plastic basin (cuvette) of a sufficiently large size, with high walls, is used for this, since it is easier to knead in it.

Further, the mass from the package is poured into the prepared container and filled with water. The amount of liquid used must be indicated on the packaging of the material. Usually 5 ÷ 6 liters of water should be used per bag. For soaking it is better to use not too much cold water, since if the process is carried out manually, it will be more pleasant to work in warm water. Yes, and the mixture at the same time turns out to be more plastic. True, you can’t go too far with the temperature in order to “weld” the composition - the recommended one should be indicated on the package (usually in the range from 25 to 30 degrees).

Next, you need to knead the mass for a long time until a homogeneous state. It should be noted that it is recommended to pour only one ÷ two packages into a container, since an excessively large amount of mass will be very difficult to mix thoroughly to a completely homogeneous consistency.

If we consider the manufacturing process step by step and in detail, it will look like this:

"Short course" in pictures

Before pouring into a container, bags with a dry mixture should be shaken vigorously for 2-3 minutes so that the dry mixture breaks up completely into components, without lumps.
Next, the mass is poured into a plastic container.
The required amount of water of the recommended comfortable temperature is poured into the cuvette.
The mass is mixed until completely homogeneous.
Then the composition is laid in polyethylene package or wrapped into polyethylene film and leave to infuse for 12 hours.
The mixture should turn out to be plastic, of medium density, so that it can be easily applied to the wall, and at the same time it would not flow down the surface. Immediately before applying to the wall, a too thick mass can be slightly diluted with clean water.

One interesting property should be noted - such a mixed composition in a closed hermetically sealed form (in the same plastic bag) can be stored without losing its properties for up to two weeks.

Prices for liquid wallpaper

Liquid wallpaper

Video: technology for working with "liquid wallpaper" factory production

How to make "liquid wallpaper" yourself?

As mentioned above, craftsmen learned how to make this type of decorative coating on their own. There is a recipe for the base of the mixture, to which various decorative ingredients can be added, depending on the desired effect. Some basic components of the foundation may also change. But in general, mixing home-made "liquid wallpaper" is carried out according to the same scenario.

The first option is from paper waste

To make a working mixture of "liquid wallpaper" you will need:

Any paper - old newspapers and books, printed sheets used in the printer, packaging wrappers and other scraps that are unnecessary in the household.
Dye of the desired color or even several colors.
PVA glue and water.
Gypsum, acrylic plaster or Bustilat glue.
As additives, crushed tree bark, dried algae, mica powder, small sparkles, pieces of yarn, crumbs of granite, quartz or other stone can be used.

The process of making the base occurs in stages, and the dye is already poured into the finished mixture. And only after it is infused, the selected additives are poured.

- The paper needs to be shredded, and The smaller the pieces, the faster the further process will go.

- Shredded paper is placed in a container, poured with ordinary water and left for 3 ÷ 4 hours so that the material is well softened. For one kilogram of paper, 5 liters of water are required.

Mixing with a mixing attachment

- After waiting the right time until the maximum soaking, the paper with water is kneaded with an electric drill with a mixer nozzle until a homogeneous mass is reached.

- Then, dye and glue are added to the resulting mixture, and then kneading is continued.

- After the specified period, the mass is unfolded and thoroughly kneaded by hand.

- If it is planned to make wallpaper with sparkles, they are also added to the mass after it has matured.

- Immediately before applying to the wall, gypsum is added to the mass, and then it is mixed again until completely homogeneous.

Here you need to remember that the more gypsum is added to the mixture, the faster it will set and harden. Therefore, you should not add gypsum at once to the entire prepared mass of "liquid wallpaper".

Video: an example of making "liquid wallpaper" from waste paper

The second option - from other fibrous materials

To prepare another version of "liquid wallpaper", you will need to prepare the following components:

Main material

Cotton or cellulose fibre. As this material, you can use ordinary cotton wool or Ecowool insulation material, consisting of wood pulp.

A lot of material will be needed if the finishing will be carried out on large areas - this must be foreseen in advance.

If ordinary cotton wool is used, then it will have to be carefully crushed. This operation can be done manually, using scissors, or you can build some kind of mixer using an electric drill with a mixer nozzle for mixing. A bucket can serve as a bowl for a mixer, in which the material is placed, but the container must be closed with a lid with a hole for the mixer shaft, otherwise the cotton wool will scatter to the sides. The lid can be made from thick cardboard.

In addition to cotton wool and cellulose, as the main material, you can use fibers - synthetic winterizer, linen fibers, polyester or wool.

These materials, as in the first case, are carefully crushed, and, the finer it turns out to be, the better and easier it will be to mix them, and the mass will come out more homogeneous.

Another option for making "liquid wallpaper" can be threads made from different materials - it can be wool, cotton, synthetics, or a mixture of several components. Often, needlewomen have a lot of leftover yarn that has become unnecessary, and besides this, you can dissolve old sweaters and sweaters that have not been worn by anyone for a long time.

The threads also need to be chopped - this can be done with scissors or, for example, with a sharp ax for chopping cabbage, but for this you need to have a wooden base on which there will be work is being done.

Of course, the work of such grinding is quite tedious, but the result will be amazing. Colored shredded threads can be used alone or as an additive to a mass made from fibers or paper.

Connecting component

As a component that holds together the fibrous structure of the "liquid wallpaper", different adhesives can be used - these are Bustilat, casein wallpaper glue or PVA, or even acrylic-based putty. However, it must be remembered that the latter, firstly, has a specific smell, and secondly, it will need to be further diluted with water.

The most resistant to abrasion and deformation are wallpapers made specifically on acrylic putty.

Decorative additives

For decorative additives, as in the first option, the same components can be used - small crumbs of various minerals, sparkles, mica, etc. Their use will depend on what effect is planned to be obtained. However, you need to immediately warn about moderation - you should not use several additives at once, as this can only ruin everything.

Supplements can be purchased ready-made. They are made from materials that will not oxidize or promote fungal growth. formations on the walls. Finding such components in building or decor stores is easy, and they have a very affordable price.

Dyes

To give the "liquid wallpaper" the desired shade, it is very important to choose the right dye, which is added to the mass during its preparation. You need to purchase formulations designed to be added to water-based paints. They are added to the wet mixture with simultaneous mixing - then they will give it a uniform shade of the desired degree of saturation.

If there is a desire to give the surface "iridescence" , that is, heterogeneity of color, in the form of inclusions and differences in tone, then you must proceed as follows:

- the first time the color is added and mixed with the mass before it acquires one even color;

- the second portion of the dye is added just before applying the mass to the wall, but this time it is not kneaded so thoroughly, leaving some areas unmixed.

The process of manufacturing the working composition of "liquid wallpaper"

From the mentioned components, "liquid wallpaper" is made as follows:

One of the selected materials is placed in the mixing container basics - fibers, threads, or both at the same time, then mixed with one of the binders. The proportions of the composition of the mass should be approximately 1:1.

Further, decorative components are added to the mass, and it is again mixed until smooth, so that sparkles or stone chips are evenly distributed throughout the volume of the mixture.

If the mixture is too thick, you can add a little water to it.

It is recommended, as an experiment, to make a small amount of finishing material in certain proportions and try to apply them to the wall. If the coating fits well on the surface and has the look that the owner wanted to get, then you can prepare the required amount of the mixture, sufficient for the walls of one room.

After the mass is kneaded, it must be left to mature for 5 ÷ 8 hours, since the fibers and threads must be well saturated with glue.

The time until the mixture is prepared can be used for applying them.

Application of "liquid wallpaper" on the walls

Wall surface preparation

As with any, for the application of "liquid wallpaper" walls require some preparation. No special efforts will have to be made, since the standard procedures for normal preparation should be followed. These include the following activities:

The surface is cleaned of the old coating, which may interfere with the application of "liquid wallpaper" - this is any old wallpaper, whitewash, oil paint, etc.

If the walls are covered with plaster, which does not have significant flaws, it does not need to be removed, since the wallpaper will fall on it without problems.
Aligning the surface of the walls to the ideal is also not Necessarily, as "liquid wallpaper" will help hide minor flaws.
If the walls are cleared up concrete base, then they should be covered and the surfaces allowed to dry well.
Then a putty leveling mixture is applied to the walls - it can be applied and spread with a wide spatula. After drying this layer, it can be applied, if necessary, a thin finishing putty composition.
And when the putty is completely dry, the surface needs to be properly primed again. Last layer primers are applied for better adhesion of "liquid wallpaper" to the wall.

After preparing the walls, you can proceed directly to the manufacture and application of "liquid wallpaper".

Prices for different types of primer

Primer

The process of applying "liquid wallpaper"

"Liquid wallpaper" will look good both on the walls and on the ceiling

After the walls are ready to "accept" decorative trim, "liquid wallpaper" is applied to their surface like thin-layer plaster.

"Liquid wallpaper" is applied like plaster with a metal spatula or trowel

However, here it is necessary to provide one more nuance for the work to be successful. The point is this. If a large amount of the mixture is prepared in advance in several batches, and the same dye is added to each batch, it would seem - in the same amount, then it will still be very difficult to withstand one Color tone. It often happens that one batch can turn out a little lighter, the other darker. This may not be particularly noticeable in a semi-liquid, diluted state. However, when drying on the plane of the wall, the difference can be visually felt very significantly - the look will turn out to be untidy.

This is easy to avoid. In preparation for application to the wall, the same amount of mass is taken from each basin or bag with batch and mixed thoroughly. After using it, when taking the next portion, exactly the same procedure is done. Thus, it is possible to achieve exactly the same color and distribution of decorative components on all walls of the room.

No need to be afraid to make a mistake - there is always the opportunity to try again

Applying "liquid wallpaper" to prepared walls is a very simple process, and even a beginner can handle this work, since it is basically impossible to spoil the material. If something did not work out the first time, then the wallpaper applied to a certain section of the wall can be carefully removed and then reapplied.

The optimal thickness for applying wallpaper is 2 ÷ 3 mm. This layer can be achieved with a metal spatula or grater. It is best to smooth the material on the wall with a transparent trowel-trowel. Using it, you can constantly keep the treated surface areas under control.

Transparent trowel-trowel - the most convenient tool for "liquid wallpaper"

The raw mass is applied to the walls and smoothed out with circular, horizontal or vertical movements, depending on what kind of design effect is intended.

Excess material protruding beyond the decorated planes is carefully cut off with a construction knife after the material begins to dry.

After the initial setting of the glue, you need to walk over the entire surface with a transparent trowel, wetting it in water - this process makes the surface even. This operation must be carried out carefully, in a circular motion counterclockwise.

If it is planned to reproduce a certain pattern on the wall, then it is applied in advance to the desired area with a pencil, making clear lines. Then the fragments of the intended panel are filled in separately, with “liquid wallpaper” of the desired color. The edges of the areas are trimmed and left for some time to set the glue.

Layer-by-layer application of multi-colored "liquid wallpaper" when creating an artistic panel

After that, those “liquid wallpapers” are applied around the elements of the ornament, which will serve as a background for it. In this way, wonderful, completely exclusive patterns can be reproduced on the walls, which will become the center of attention of the room.

Video: master class on working with "liquid wallpaper" - "silk plaster"

The production and application of "liquid wallpaper" can be fully called a creative process, which is available to almost everyone who has a desire to try their hand at this art. Therefore, if the idea arose to decorate a room or part of a wall in a completely original way, you need to boldly get down to business and start creating.

In this article, you will learn how to prepare walls for liquid wallpaper. Preparing the surface for applying liquid wallpaper is as follows:

old coatings in the form of wallpaper are removed;
on a wall covered with oil paint, dirt is removed, and the surface is primed with water-dispersed paint mixed with fine sand to create a roughness;
all types of contaminants are removed (grease stains, rust, soot, etc.);
all metal objects (protruding fittings, nails, etc.) are primed with light matte nitro enamel;
the surface of the walls is leveled, minor defects may not be deleted;
after cleaning and putty, the surface is primed with light matte nitro enamel;
at the first coating of new walls, they are primed with water-dispersion paints.

Liquid wallpaper is a dry powder that is diluted with water. The powder is composed of particles
cotton, wool, decorative additives, silk and most importantly an adhesive that gives a hard coating after drying. The necessary information is indicated on the packaging of liquid wallpaper, the expiration date of the composition, and so on.

Liquid wallpaper can be applied to any type of surface - brick, drywall, metal or wood. Liquid wallpaper has excellent adhesion, so it can be used with any materials and even during operation it adheres well to the walls. The main thing is to properly prepare the surface, not missing the slightest detail.
Meanwhile, the surface in any case should be as strong as possible. In order to strengthen weak points, it is plastered. If this is not done, after a while the coating on the walls will begin to crack and crumble.
The base on which the wallpaper is applied should not absorb moisture too much. In addition, the base should not emit coloring matter when exposed to moisture. So, for example, for metal surfaces, the problem is rust, which appears on the surface of the wallpaper.
You can not apply liquid wallpaper on walls that are covered with old wallpaper or putty. Previously, all areas are cleaned with fine-grained sandpaper, and small cracks can be repaired with the liquid wallpaper itself. Naturally, the consumption of material will increase.

Preparing walls for liquid wallpaper

To ensure maximum surface strength, it can be treated with a colorless primer with a high adhesion value.
Such a primer mass will prevent the penetration of moisture and make the surface more durable and reliable. You can also pick up a concentrated primer, which is diluted with a solvent or drying oil, but it should be remembered that stains may appear on liquid wallpaper from it.
If the surface has any metal elements (nails, screws, fittings), such places should be treated with paint, which will avoid contact of the wallpaper with metal surface. Oil or latex paint is suitable for this. The final step in working with liquid wallpaper is to roughen the surface. If the surface is already a little rough, for example, covered with putty or unpolished plaster, liquid wallpaper can be applied to it immediately. If it is planned to apply the material to concrete or treated wood, then the surface is pre-treated with a primer with quartz dust. Otherwise, liquid wallpaper will simply roll off. This primer is very easy to prepare. It is enough to add quartz or marble dust to the usual primer mixture, and if they are not there, then the usual quartz sand then mix well.
painter's advice
For savings liquid wallpaper the base under them is made quite rough. Thanks to this, the mixture lays down in an even layer and adheres perfectly to the surface. When applying liquid wallpaper to a smooth surface with a spatula, gaps and gaps may form.

Preparation of liquid wallpaper

It is not enough just to buy liquid wallpaper - the mixture must also be properly prepared for application to the surface. First, the bag is shaken vigorously to mix the mixture well and improve the fine structure of the liquid wallpaper (so that there are no small lumps and the mixture mixes easily).

For one package of wallpaper, a mixing container with a volume of 7-8 liters is suitable. Usually choose a container with a depth 20-30 cm, to make it easier to wash it and knead the solution in it.
For the solution it is necessary to use only clean water with a temperature 20-30 3C. The temperature does not affect the quality of the finished solution, but it is more convenient to knead liquid wallpaper with just such warm water. You can stir both one package and several at once, but in this case it will be much more difficult to achieve sufficient mass uniformity. The second option is relevant only when liquid wallpaper can have a different shade and it is necessary to achieve the same color.

So, how to prepare liquid wallpaper?

To do this, pour the entire mixture from the bag into the container and then add about 5 liters of warm water. As the water is poured in, you need to constantly stir the solution, achieving a uniform mass. The mixture is always prepared by hand, no mixer or other equipment is used. If it is difficult to mix one package on your own, you can try kneading the solution in small portions.
The consistency of the ready-to-use solution should be like heavy cream. Approximate material consumption is 5-6 l per sachet of mixture.

Types of liquid wallpaper

1. Silk wallpaper. Their basis is a special silk fiber. Such liquid wallpapers are the most
durable and high quality, moreover, resistant to ultraviolet and temperature effects and can last a very long time. Accordingly, wallpapers of this type are considered one of the most expensive.

Types of liquid wallpaper

2.Cellulose liquid wallpaper relatively inexpensive, but their quality is not the highest. Therefore, they are purchased so that the surface of the walls and ceiling looks beautiful and modern, but at the same time, cosmetic repairs can be done inexpensively and quickly.

There are also silk-cellulose wallpapers, which seem to be a compromise option both in terms of price and quality. Therefore, if the budget for finishing surfaces allows it, most buyers tend to use them.
Depending on how the wallpaper will be used, they can be completely ready for use or ready for painting.

Types of liquid wallpaper Types of liquid wallpaper

In the first case, the wallpaper is diluted with water and immediately applied to the walls. This option is suitable even for those who have never worked with this material.
In the second case, the material is presented only in white, and additional color and texture components are added individually. It is difficult to work with such liquid wallpaper, because it is difficult to guess with color saturation. Therefore, with wallpaper for painting, as a rule, only professionals work.

Modern high-quality liquid wallpaper on the basis of characteristics can be classified as textile, as they are made on the basis of natural silk and cotton natural fibers. The composition contains components such as cellulose, fire-resistant additives, high-quality innovative adhesives and acrylic substances. This coating looks like ordinary textiles, walls and partitions seem modern, draped with aesthetic silk materials.

This material differs from ordinary roll wallpaper. appearance, but also by the method of application, which in many respects is similar to decorative plaster. Another advantageous difference is the ability to prepare liquid wallpaper with your own hands. You can find out how to make such liquid wallpapers, how to lay them with your own hands in this article.

Do-it-yourself coating features

Before describing the process self-manufacturing liquid wallpaper, it is worth studying the features of the composition. The following components are present here:

Paint, moreover, a dye made on water.
The main material is cellulose and plain paper.
Special composition for bonding the base, for example, glue.
Accessories, among which there may be sparkles, as well as stone chips.

The material is used in the process of decorating walls, various partitions, and all categories of buildings and structures. Liquid wallpaper is ideal for decorating a bedroom, living room, children's room.

The production of liquid wallpaper does not take a lot of time resources, while all the work can be done in living conditions, that is, it is not very complicated, as you might initially think.

Important! Liquid wallpaper is characterized by a huge number of advantages, among which there is the possibility of effective finishing of such parts of the room as bay windows, various ledges, decorative columns, as well as corners.

Do-it-yourself liquid wallpaper manufacturing instructions

Before doing wallpaper on your own, it is recommended to carefully prepare for this process. One of the most important criteria is the preparation of a special container where the mixture will be mixed. It is advisable to prepare a simple plastic basin with a diameter of at least 50 cm and a depth of 40 cm. It will be quite convenient to mix all the necessary components in such a container.

Requires clean water room temperature or even warmer. This parameter is important only for the reason that it will be more comfortable and convenient to mix the resulting composition; this does not have any effect on installation and technical qualities.

Important! If it was decided to independently prepare liquid wallpaper from the material purchased at the hardware store, it is worth making sure that all the components used are from the same batch.

Along with the prepared container and water, it is worth finding and preparing paper, adhesive composition, gypsum, color. It is better to use paper that is not very thick, the remnants of office paper are perfect, which is better than newspaper, as it has a white color. In this case, it is important to monitor the absence of various foreign objects. It can be a metal bracket, glue residue, rope.

To prepare the mixture, it is worth following certain instructions, following a certain sequence of actions. You will have to carry out correctly selected and consistent actions:

Important! If for some reason the composition turned out to be dense and dry, you can add a small amount of water to it and stir everything.

As soon as the entire mass is completely saturated with water, it is worth leaving the resulting composition for infusion. This time can be from 6 to 12 hours, and this is required in order for the glue to effectively soften and thoroughly bind all the fibers.

It is not worth preparing a large amount of material at once. It is enough to prepare it in parts, that is, for one element of a building or structure and with small reserves. This is very important rule, since it is impossible to do it twice in a row same composition, that is, when applied to the wall, visible transitions may form. In wall transitions, such transitions will not be so visible. If after mixing the composition a small amount of wallpaper remains, they can be safely added to the next batch.

As for the quantity, if liquid ones are bought at a hardware store, then the package will be enough to process 3 meters of walls. It is worth knowing that the solution may well stand for several hours and remain fully usable; it can be stored in the closed state for several weeks.

Preliminary measures before application

Self-made liquid wallpaper can be applied without any problems on surfaces made of concrete, on surfaces finished with putty. Also, the material will ideally lie on brick and professionally plastered surfaces. The material can be used when finishing country surfaces, as it fits perfectly on wooden structures. it can be fiberboard, plain plywood and MDF.

With wallpaper of this kind, you can finish plasterboard surfaces and painted walls. Liquid wallpaper can be applied to all such surfaces without any problems. To obtain an ideal result in all respects, simply follow the instructions and recommendations listed below, most of which relate to the preparation of wall surfaces.

It should be understood that all subsequent work is characterized by certain features that must be taken into account. The surface is being prepared. It is important to comply with the following requirements:

Uniformity;
Full uniformity and minimum moisture absorption;
Its shade should be white or, in extreme cases, should match the shade of future wallpaper;
The complete absence of various drops, potholes, and various depressions is important. If they are, then more than 3 mm;
High strength values are required.

Before application, it is very important to completely remove all old wall coverings. This is necessary for the reason that the old coating after applying liquid wallpaper to it can quickly peel off. At the same time, old fasteners are completely removed - self-tapping screws, screws, nails, plastic and metal parts that stick out of the wall. If these are elements of reinforcement that cannot be removed, it will need to be bent and sealed very carefully. This can be done with a regular 2 mm putty.

When preparing the walls, it is absolutely not necessary to bring them to a perfectly even level and make them completely smooth on your own. The advantage of liquid wallpaper is that the application does not emphasize depressions, as well as serious protrusions, moreover, you can not notice even a serious slope of the surface.

Applying liquid wallpaper on the wall with your own hands

To work, you need to prepare tools such as a plastic grater, a construction trowel, a conveniently sized spatula, and a spray gun. For wallpaper, it is worth buying a grater, which is distinguished by a narrower canvas. They are made of completely transparent plastic, then smoothing can be visually controlled. This helps a lot in the process of compiling a variety of applications made from a variety of categories of material.

As for the application process, it is quite simple. In many ways, it is similar to working with ordinary decorative putty, just a little simpler and lighter. Application consists of the following simple and understandable steps:

Important! If the composition is not very well attached to the wall, and also if it is very thick in structure, it is worth adding a small amount of water.

There are several rules for applying the material. If you follow them, you can get an ideal surface in all respects. The main rules include:

The grater must be kept not flat, but slightly raising the edge by 5-9 degrees relative to the wall;
Efforts should not be very pronounced, it is enough just to distribute the solution to the desired one;
After filling one meter of the wall, you can move on to the next, but before that, with a grater, it is worth slightly leveling the previously designed area to prevent the appearance of furrows and lumps. Then you can start applying the next section itself;
The type of wallpaper applied directly depends on the direction in which the grater moves. It is in the direction where the tool is directed and the fibers will be laid;
To obtain the most aesthetic and even wall, each applied portion must be separately leveled with small multidirectional movements. Many make small twisting movements to give some originality.

At wall joints, liquid wallpaper is recommended to be leveled strictly in the direction from some certain angle to the side. If the wallpaper is applied on some area strictly in one previously selected direction, in adjacent areas, change it by about 45 degrees, it is quite possible to get quite interesting drawings.

Partial restoration and repair of liquid wallpaper

Quite often, situations arise when it is necessary to carry out a small additional repair, during which it is necessary to remove a small section of the wall. This may be necessary when changing wires or for small cosmetic repairs. What should be done in such a situation?

You just need to prepare a spray gun and a spatula. Using these tools, you need to carry out the following activities:

This technology is ideal for replacing coatings on small areas. If after the finishing works a small amount of solution remains in the presence, they can be dried by spreading on an open surface.

Many, after applying the composition, decide to give them strength. For this, a colorless varnish is applied, preferably on water. After the work done, you can get the usual washing wallpaper.

Important! This method does not make liquid wallpaper resistant to moisture. For this reason, wallpaper should not be applied in kitchen area and in the bathroom. for this purpose, moisture-resistant high-quality wallpaper is provided.

Average prices for liquid wallpaper

Features of the use of liquid wallpaper in various interiors

Modern manufacturers produce a decent variety of liquid wallpaper, made in the most unique color solutions and different in structure. This allows you to quickly decorate the premises in a variety of style solutions. In order to get the perfect result during the finishing process, it is worth choosing the type of wallpaper correctly, based on the purpose of the room.

There are the following preferred interior design options:

The method of decorating a room in an English style decision is popular. In this case, the entire wall is divided into separate sections by means of borders. Each element inside is decorated with wallpaper that differs in color.

With liquid wallpaper, any room can be truly exclusive. With your own hands, the interior can be made stylish and attractive.

Liquid wallpaper in the interior photo

A few photos of ideas for using liquid wallpaper in interiors:

Positive qualities of liquid wallpaper

The described modern coating corresponds to GOST. Advantages provide an optimal opportunity to use the material for interior decoration of residential buildings and structures, but also for office decoration. In addition, it is an ideal option for finishing buildings located outside the city that are not heated in cold weather. Covering the walls with liquid wallpaper perfectly tolerates various temperature extremes and high humidity. Other equally important benefits include:

fire safety;
Environmental friendliness;
Moisture resistant;
Perfect anti-static;
Vapor permeability;
Excellent covering qualities, that is, the complete absence of seams and cracks;
The possibility of interior design in a variety of style solutions;
Simplicity in design and application;
Affordable cost;
The coating can be quickly restored;
Liquid wallpaper is durable, they can last up to 10 years.

It is very easy to work with the material, the process of finishing the room is even easier than with the help of ordinary wallpaper. In the latter case, it is necessary to more carefully prepare the walls and working area. The composition is mixed in a small container, and the application process is carried out from a certain local area.

Ease of application contributes to the fact that literally half an hour you can finish about 6-8 square meters different complexity of walls and partitions. There are compounds that are applied using standard construction sprayers. This provides maximum economical consumption material, which is very convenient when finishing the ceiling.

Summing up

Covering with liquid wallpaper makes it possible to avoid long-term preparatory work. This is a fairly thick mass of mortar, which is able to effectively hide such minor defects as cracks, crevices and other surface defects. Liquid wallpaper can be used as a putty in the process of filling gaps that often form between walls and skirting boards, as well as in areas of frames, switches, trim, sockets and various decorative elements. With the help of this coating, you can equalize the corners. The coating is ideal for wall decoration in new buildings. The material does not crack with possible deformation of walls and ceilings, with their shrinkage.

Liquid wallpaper is relatively easy to care for. It is enough to clean them with a vacuum cleaner from time to time, you can carry out wet cleaning by wiping the walls with a damp soft sponge or napkin. If small stains appear on the walls, it is enough to use stain removers. If mechanical damage forms on the surface, the problem is easily fixed by replacing the damaged area with new material.

Modern coatings are absolutely not afraid of pets, tricks of small children, communal problems, such as flooding. All problems are very easily and simply eliminated, and the apartment becomes clean, cozy and warm. A wide variety of choices allows you to get an ideal and stylish interior after the repair.