How to make the back of a chair higher with your own hands. DIY armchair - step by step instructions for creating upholstered furniture. Councils of designers for the design of armchairs. The final stage - decoration

You can make a chair with your own hands from different material. Wooden furniture is a reliable and original design. To make a slatted chair with an inclined seat, you will need a bar (section 28x28 mm), plywood (18 mm thick), stain, glue, M8 studs, a primer, oil paints. From the tools you will need a miter box, a screwdriver, a sponge, a brush, a planer, a drill, drills.

Step-by-step instruction

The bars used to make the model in question must have a single section. The blanks must have the same thickness along the entire length and perfect linearity. Otherwise, the chair geometry will be distorted. First you need to make a drawing of the product. The dimensions of the constituent elements are indicated on the diagram of the chair.

The beam is cut into strips, the length of which is 50 mm. To assemble the back and 2 side walls, you will need 36 planks, including bearing bars for the seat. The wood is cut with a circular saw. At the edges of the bars, holes with a diameter of 8 mm are made and drilled.

The distance from the end of the rail to the center of the hole should be 25 mm. To maintain the dimensions, distances and perpendicularity of the holes, a drilling stand is used.

To make the chair smooth, the ends of the rails are treated with abrasive sandpaper. Longitudinal planks are rounded with a planer, cleaned with sandpaper. Square parts are made from a similar beam, the parameters of which are 28X28 mm (checkers). They are installed between the slats, forming a lattice base of the product. Their ribs are chamfered. Then through cuts are made, which should coincide with similar elements provided at the ends of the slats.

Each part is glued with 2 checkers. A guide pin made from scraps is inserted into the hole. Workpieces are aligned. For this, rails are used. The assembled elements are tightened with clamps. It will take some time for them to dry.

Back to index

Additional points

To increase the operational life of furniture, wood stain is used. Previously, the blanks are hung on a beam. The stain is applied to the checkers and planks with a sponge. Excess solution will need to be removed with a brush. If the stain is dry, then the elements are primed, sanded with a zero and varnished. The parts are dried on a special plate with dowels. Painted parts are installed on the last elements. In this position, the parts are until completely dry.

The next step is to cut the back and seat of the chair from plywood. The resulting products are twisted together with screws. To increase the strength, dowels are additionally glued. The resulting design is painted red, dried and varnished. Holes are made in the blanks, the diameter of which is 8.5 mm (for studs). The design is slightly tightened with threaded bushings.

To screw the seat, you will need to drill holes in the supporting elements. The seat is installed and screwed from below with screws. The resulting furniture will look original in any interior (see photo).

Back to index

DIY garden furniture

To make a garden chair with your own hands, you will need electric jigsaw, Sander, nozzles, screwdriver, drills, brushes, tape measure, right angle, pencil. The sides and tie-backs (parameters 800x120 mm) are made of euro plywood (thickness 30 mm). The above details are cut out of this material, taking into account the previously made drawing. The corresponding diagram shows the dimensions of each component of the chair.

In the process of transferring the contour to the workpiece, slight deviations from the specified parameters are allowed.

The sides should not have protruding corners on the rolling (lower) side. 35 pieces are cut from a beam with a cross section of 50x25 mm (the length of each rail is 1200 mm). Of the fasteners, 12 pieces will be required. confirmations (5x120 mm) and 140 pcs. wood screws (4x45 mm).

The next stage involves the processing of wood. To sand the surface of the timber, you will need a grinder. Particular attention is paid to the ends of each detail. They are varnished and further processed (before the assembly process of the entire structure). Experts recommend impregnating the ends with hot drying oil, lightly hammering the fibers with a hammer.

It can be seen from the drawing that the holes for the drawers can be placed arbitrarily. The plane of the sidewalls is drilled through. For this, drills with a diameter of 8 mm are used. For the tsarg, this figure is 5 mm. In the bars, with the help of which the reclining surface is formed, 140 symmetrical holes are made. It is recommended to use a jig for this - a special device that allows you to place a large number of identical elements.

Not only craftsmen know how to make exclusive comfortable furniture from improvised materials. The advantage of such an occupation is obvious - it is the possibility of translating into reality the most daring ideas for the diversity of living space. An additional bonus is the low cost of making homemade soft chairs with your own hands. Following the advice of designers, you can do easy chair to have a good time in own house. At home, you can exactly repeat all the stages of factory production of this modern and convenient attribute for decorating a nursery or living room. On the Internet, you can find both the simplest and most complex schemes.

The first step in making homemade upholstered furniture serves as the choice of fabric for the external design of the soft parts of the structure. Each master selects upholstery depending on physical properties and price aspects and features that different drawings have. Consider the most common fabrics for decorating chairs in our time:

velor - velvety to the touch, gives the furniture a certain charm;

Velor upholstered

flog - a distant analogue of velor, easy to clean, so designers use it to decorate children's upholstered furniture;

Flog in upholstery

chenille - a fabric based on a combination of natural and synthetic fibers, has a special wear resistance (a well-thought-out structure prevents the formation of pellets);

Chinille in upholstery

jacquard - the upholstery is considered durable, but over time, the loops turn into puffs;
natural tapestry - the most expensive and beautiful view upholstery fabrics;

Jacquard in upholstery

artificial suede - a universal option for armchairs in a sunny room, resistant to UV rays and easy to clean;

Upholstered faux suede

leatherette is a durable material that allows you to play with decorative embossing.

Leatherette in upholstery

Material, fittings, tools for frame attribute

Creating a frame chair from scratch presents some difficulties. But the finished product will have a more respectable appearance. You can verify this by looking at the photos of finished products by home craftsmen. You can also use the old Soviet "grandmother's" chair for the base.

To make a simple frame for a soft chair, you need to pick up strong sheets of 20 mm plywood for cutting out parts with your own hands. Also useful is a standard repair tool kit with an electric drill, jigsaw, steel ruler, emery cloth, metal rims, masking tape, pencil, tape measure, thin nails, self-tapping screws, wood glue, stain, glossy paint. For upholstery you need: artificial leather or fabric, foam rubber (filler).

Step-by-step creation of upholstered furniture with a wooden base

If you do not know how to make a drawing for the base, then look for ready-made schemes on the net. As a rule, they are transferred to a cardboard template with a pencil. Only after that proceed to perform the operations of the described algorithm. This will help save on excess material, or vice versa - do not buy the missing parts.
According to the cardboard template, future constituent elements are cut out of plywood sheets:

banana-shaped sidewalls;
cross bars.

It is important to determine the desired angles of inclination, bending and dimensions of the future frame. This will help the photo of the finished chair, created according to your scheme.

The next step is surface treatment. wooden parts cleaning and polishing. With special care, the ends are worked out to improve the quality of the work done. Previously, these parts are impregnated with heated drying oil and only then bends are formed with a hammer, if they are provided for in the sketch. Each component is cut with an electric jigsaw.
Stained or treated with varnish-stained sidewalls. The ends of the side parts are reinforced with metal rims.
The next course of action is connected with the close-fitting of the frame. Using an electric drill, make the necessary holes. The rims are fixed with screws.
First, the back of the back is covered with artificial leather or fabric, then the remaining fragments of the structure, incl. and seats.
The upholstery is fixed with wallpaper nails, which are characterized by large hats. In the back of the frame chair, the upholstery is fixed along the edge, along the transverse parts to better cover the slats.

Pattern of a round chair wooden frame We sheathe the frame with fiberboard cardboard

Experienced furniture makers advise the attachment points to be additionally treated with wood glue. Such a move is needed to increase the durability of the created furniture with your own hands.

Secrets of reliable upholstery: how to sew

The process of stretching the upholstery of soft chairs has its own nuances:

Foam rubber is cut to the size of the seat (average thickness - 5 cm). The part is glued to the surface of the plywood sheet.
Horizontal and vertical fabric straps are fixed to the back with a construction stapler. Similar belts are added to the armrests and sidewalls from the inside along the form.
From a piece of foam rubber 0.1 cm thick, a part is cut off, which will be larger in size than the area of the seat (difference by 4-5 cm). They take a flap of synthetic winterizer fabric of the same size with an elongated front part and fix it with their own hands.
After the done manipulations, the upholstery is covered with furniture fabric. With the help of a stapler, textiles are fixed in all corners of the cover, the synthetic winterizer-foam layer to the seat frame of the chair.
The sidewalls and armrests are also covered with synthetic winterizer, fixed with aerosol glue over the entire surface. Only after that, the parts are sheathed with a cloth, securing the flap along the staples.

We sheathe the chair with foam rubber. In addition, we put a synthetic winterizer

An armchair is one of the most comfortable, cozy, and therefore popular interior items. All chairs are usually divided into 2 categories: with or without a frame. The finished product is often expensive. But for home masters, nothing is impossible. A do-it-yourself chair is a completely solvable issue. In the article, we will consider detailed master classes on the manufacture of soft products, as well as the original wooden product for giving.

Upholstery types

Upholstery for upholstered furniture - one of them important points. The presentable appearance of the product largely depends on it. Before you make a chair, decide on the type of upholstery fabric. Here are the most popular options:

Velours. Noble fleecy fabric, reminiscent of short fur.
Chenille. Pile resistant fabric made from a mixture of natural and synthetic fibers. Does not roll down, keeps a beautiful look for a long time.
Flock. Outwardly, matter resembles velor, but even more practical. Flock is easily cleaned of dirt, so it is recommended to use it for upholstered furniture in a nursery.
Jacquard. Durable dense patterned fabric, which is distinguished by increased durability. The disadvantage is that due to careless handling, puffs may appear.
Artificial suede. High-strength material, which is great for making your own chair. Embossed faux suede looks especially beautiful.
Tapestry. Solid expensive fabric made of natural fibers, with visible weaving. Threads of different shades form a pattern.

A set of necessary materials

If it's about frame structure, the easiest option for the frame is plywood cut according to the template. The best option- birch plywood. Of the consumables - screws and nails.

You will also need a set of carpentry tools:

Metal ruler, compasses, protractor - for marking.
Vise: manual and desktop.
File.
Hacksaw.
Hand scissors.
Hammer.
Adjustable wrench set.
Soldering iron.
Pliers.
Drill.
Kerner.
Chisel.
Punch.

Important! If you want to make a fashionable and non-standard bean bag chair with your own hands, then the set of necessary equipment will be significantly reduced. It only takes sewing machine and stuffing material.

Work planning

The beginning of any business is drawing up a clear plan of action. Consider the design of future furniture. It is more difficult and expensive to make frame chairs, but they look more respectable than those of frameless structures.

Success in the manufacture of a bean bag chair depends on how accurately and correctly the patterns are drawn up. This is not so much furniture production as the art of tailoring. Do not forget to calculate the budget of the event.

Important! Not bad if you have an old, but quite decent and durable chair. In this case, much is simplified, since you can restore it and get an interesting vintage thing.

Classic soft product

Such a thing as a do-it-yourself easy chair requires a long preparatory phase. From the materials you will need:

Plywood 20 mm thick.
Sandpaper.
Electric drill.
Sets of screws and thin nails.
Electric jigsaw.
Metal bands.
Foam rubber.
Glue for joinery.
Painter's tape.
Line, roulette.
Stain, glossy black dye.
Pencil.

Now you can get to work:

Download the drawing of the chair you like, calculate the consumption of materials.
Make cardboard templates to scale, transfer the outlines to plywood, then cut out the details with a jigsaw.
Clean and sand the surface of the wooden parts. Pay special attention to the end areas, soaking them well with drying oil.
Paint or stain the sides. Reinforce the end parts of the sidewalls with metal rims. Fasten the rims with screws.
The next step is the wrapping of the product. Start fitting from the back of the back, using artificial leather. Next, proceed to tightening the rest of the parts of the product. Secure the fabric with wallpaper nails.

Important! It is advisable to treat the attachment points with carpentry glue. The chair will be more solid.

Bag chair

This product is also known as the pear chair. To make it you will need:

Coarse calico or satin fabric - 3.0 m.
Fabric for the manufacture of the outer cover - 3.5 m.
Zipper - 1.0 m.
Filler.
Pieces of contrasting fabric for decoration.

The procedure for the manufacture of this chair model is as follows:

Download the bean bag chair patterns that you like the most.
Make cardboard patterns to scale.
Transfer the contours of the chair to the fabric. You will need to sew the inner and outer covers separately. As a result, you will get 2 bottoms (top and bottom) and 6 cloth wedges.
Sew the wedges together. Leave in the received bag small plot unwired. Sew the top and bottom bottom. After you have finished sewing the top cover, sew the inner cover in the same order.
Cut out decorative elements applications and sew on outer part.
Insert the "zipper" into one of the wedges. In case of contamination, you can remove the outer part and wash.
Fill the inner bag with synthetic filling about ⅔. Now it remains to put the inner bag in the outer one. Zip up.

The armchair is ready! As you can see, there is nothing particularly complicated here.

How to make an easy chair with your own hands for a children's room?

Making a frameless easy chair for a nursery is no more difficult than a regular bean bag chair. The difference is only in color.

Important! It is better to choose a fabric that is bright, attuning to positive and cheerfulness. Shades should not be too “flashy” and annoying.

Here is one of the options for upholstered furniture in the child's room:

The frame chair can be made in the form of a semicircular sandwich. For the back wall, hardboard is used, for the front - plywood.
Carefully glue the furniture foam rubber onto the base, on top of which the upholstery will lie.

Important! the best options upholstery material are flock or eco-leather. Even if a young artist paints the upholstery with felt-tip pens or paints, you can remove the traces completely.

The maximum height of the baby seat must not exceed 600 mm.

Wooden chair for giving

Here's another interesting option: armchair made of wood with your own hands. Wood is a practical, beautiful and durable material, which, moreover, is perfectly processed. In addition, wood self-manufacturing home or country furniture has the following advantages:

The availability of a variety of lumber, their relatively low cost.
Naturalness, ecological cleanliness.
Nice smell of wood. Coniferous wood smells especially pleasant.
Unique wood grain.

Important! It should be taken into account that the conditions in which country furniture is, if not extreme, then close to them. Therefore, special attention should be paid to the processing of parts with an antiseptic. In this case, the furniture will serve you much longer.

Best for home furniture production suitable pine, spruce, ash, oak, larch or beech. Details that are not heavily loaded can be made from linden or alder.

So, we make a garden chair with our own hands. Choose simpler drawings to start with. When choosing a design, be guided by two “golden rules”:

Choose the design that is completely clear to you. Mentally work through the entire procedure. Prepare in advance the tools that are convenient for you.
Consider the place of use of furniture and the design of the room in which this very furniture is to be entered. For example, the best option for giving is a folding product or an antique rocking chair.

Manufacturing procedure

Consider a simple model, which consists of the following components:

Sidewalls - 2 pcs.
Tsargi - 3 pcs.
Cross rails - 35 pcs.

It is these 35 rails that will form the surface of the seat.

Most hard part work is cutting out the side parts:

First, make a pattern on cardboard, and only then, making sure that the steps are correct, transfer the outline to the material. The best option for making sidewalls is plywood with a thickness of 3 cm. Use an electric jigsaw to cut out parts.
Sand the ends of the sidewalls. Using a manual router or grinder, chamfer.
Now cut out 3 drawers from plywood. The length of each is 120 cm, the width is 10 cm. Sand these parts, no need to chamfer.
From a 50x25 mm bar, cut 35 segments, each of which is 120 cm long. Next, as usual, is sanding and chamfering. For fastening, prepare 12 confirmations 5x120 mm and self-tapping screws for wood 4x45 mm (40 pieces).
Mark the places for fastening the tsarg. There are 3 of them in total: in the foot, head and in the middle of the outer arcs of the sidewalls. Drill through 8mm holes for the sides.
Pull off the side parts of the product with three sides. For holes in the end parts of the drawer, use a 5 mm drill.
Now fix the pre-prepared segments of the bars to the seat using self-tapping screws.
The final stage is to cover the zenoks and cracks with putty on wood. After that, sand the product, prime the surfaces and paint with varnish or acrylic paint.

footage

As you can see, making a chair with your own hands is quite realistic. In self-made chairs different types there is nothing particularly difficult. Good luck to you!

The armchair is good place both for work and leisure. Before you make a chair with your own hands, you need to familiarize yourself with its models, since there are a large number of chairs. For some models of chairs, willow or rattan is needed, as when presented in other materials, they lose their charm. This piece of furniture can also be made of metal - forged rocking chairs look like jewelry in the interior.

Chair drawing.

DIY chair - wooden chair

Solid wood furniture is a symbol of solidity and reliability, even if it is a lattice model. It does not take much time to make a chair from a bar, and it can serve for many years without needing restoration. For manufacturing you will need:

medium thickness timber;
plywood;
wood glue;
primer;
stain;
furniture dowel;
self-tapping screws;
sandpaper 3 types;
Bulgarian;
screwdriver;
hand drill;
plane;
clamps;
sponge or foam rubber;
brushes;
pencil or marker;
square;
dye.

Chair making tools.

The thickness of the beam does not matter much, but when buying, you need to pay attention to a single section, which simplifies work and shows the quality of the workpieces.

Ideally, all blanks should be of the same thickness and with good linearity.

If one of the parts is twisted, this will greatly affect the integrity of the product, it may warp or crack during operation.

How to make a chair - manufacturing process

The beam is sawn into the required number of transverse slats and bearing additional seat crossbars. Good and fast work allows the presence of a circular saw. The edges of the resulting bars are marked, and drilled at the same distance through holes. The distance from these future fasteners to the edge of the bar must be at least 25 mm, otherwise the hand-made chair will not be strong enough. A drilling stand will help you accurately maintain all the parameters for a variety of holes, on which you can set parameters such as the perpendicular of the holes, their dimensions and distance.

Before making a chair, one more safety concern is required - to process the ends and surface of the slats in order to exclude the appearance of splinters during operation.

In this case, all existing ribs are rounded with a grinder or planer. When the longitudinal slats are ready, the remnants of the beam are divided with a circular saw into squares, which will be used to separate the slats from each other in the structure.

Scheme of assembly of a garden chair.

Holes are also drilled in them, coinciding with those already on the finished bars, they need to be sanded and the ribs smoothed. Each master will determine the number of long bars and squares for himself, starting from the size of the chair and the thickness of the bar.

Dowel fasteners are inserted into the holes, a few drops of glue are added, after which each bar on both sides is connected to a pair of cubes. The blanks are aligned along the edges by attaching a rail, then left to dry, tightened with clamps. After drying, the wood is treated with stain. A rope can be threaded through the holes in the parts and the painted parts can be hung to dry. In the same way, varnishing occurs.

To make a chair with your own hands, the back and seat for the chair are cut out of plywood. They are twisted together using a pair of screws on the right and left. Additional strength can be given by dowels if holes are drilled under them and glued before use. All parts are painted in the desired color and varnished after drying. It remains only to make the final assembly of the body with the help of bushings and screw the seat. This unusually shaped bright and catchy armchair complements the interior well.

Do-it-yourself garden easy chair

Not everyone likes plastic chairs, which are currently used everywhere for decoration in the country house or in the garden of the recreation area. Garden light chairs made of wood look more appropriate on the site, and their manufacture does not take much time. Before you make a chair, you need to consider that its design should be light and comfortable, it is best to prefer a folding chair. This will allow you to quickly transfer furniture under the roof in case of rain, because even well-treated wood should not be exposed to moisture.

Scheme of connecting the legs of the chair.

Wood, in order to make a chair, you need to choose from hardwoods such as beech, walnut or oak. Pine, cedar, larch or aspen are also little susceptible to decay, but at the same time, pine is not resistant to mechanical stress, large dents remain on the surface. Boards should be chosen well dried or dried under a canopy before starting work. Materials and tools will need the following:

Circular Saw;
milling cutter;
hacksaw;
plane;
screwdriver;
drill;
clamps;
grinder;
roulette;
square;
pencil;
sandpaper;
screws or screws;
wood glue;
drying oil or furniture varnish;
stain.

Preparing and assembling parts

A garden chair will require two rear and two front legs, with the rear legs being longer. You need to cut out 2 supports for the armrests, a backrest and a jumper. For the rear pair of legs, armrests, backrest and seat, boards matched in color and texture are glued together until the desired width is obtained. To qualitatively glue the tree, grooves for the dowels are chosen at the ends. Paired parts can be sawn out at the same time by pulling two boards with clamps.

Rocking chair drawing.

Details are then adjusted to size using a milling cutter or planer. When cutting the back, the glue line, if present, should be placed in the middle of the part. The upper edge is rounded, and after that you can start assembling the garden chair, adjusting other elements as needed.

The rear legs are attached to the backrest with screws reinforced with glue. To ensure that the workpieces do not crack during assembly, the holes for the fasteners can be drilled in advance. The strength of the assembled seat will depend on the correct location of the boards on it. They should lie in the direction from one leg to another. The front legs are also screwed onto screws or self-tapping screws reinforced with glue.

Reliability and stability of the chair is given by a proleg - a jumper located between the front legs. Fasten it similarly to everything else, using glue and screws. Then the armrests and the support for them passing behind the back of the chair are attached.

The heads of all screws used for fastening should be sunk flush with the surface, and then closed with special plugs. The wood of the finished chair is impregnated with hot drying oil or stain, dried, varnished in several layers. You can opt for a special furniture varnish, but parquet or yacht varieties have the strongest coating.

Design for rocking chair

This chair can be used both in the garden and at home. By expanding the seat, it is possible to make not an armchair, but a whole bench on which several people can fit. For manufacturing you will need:

Chair seat assembly diagram.

electric jigsaw;
grinder;
drills for wood of different diameters;
screwdriver;
square;
roulette;
pencil;
plywood;
self-tapping screws;
confirmations;
slats.

If the rocking chair is made by hand from start to finish, it is better to use high-quality materials so as not to spoil the work.

Making a rocking chair

The sides of the chair with a rounded bottom are cut out according to the developed pattern in the first place. They should be completely identical, and there should be no protruding corners on their lower part. Then a beam for the seat and back is cut, the number and length of which must be calculated separately for each model. The surface of each bar is sanded and polished, the corners are smoothed. If you plan to use the chair on the street, the ends of the boards should be given special attention. They are varnished at least 3 times, since it is there that the wood is especially loose and needs protection from atmospheric influences. In order to protect the street and garden furniture, the ends are impregnated several times with hot drying oil, and the fibers are flattened with a hammer.

The sidewalls are pulled together to the desired size by several drawers, drilling through the sidewalls. Then holes are drilled in the ends for fastening the bars. The bars themselves are also drilled in advance to avoid cracks during operation. It is more convenient to fasten the bars not between the sidewalls, but on top, somewhat going beyond the contour. In such a rocking chair there is more space, and it looks neater. Each screw should then be covered with an antiseptic and a plug placed on top. After that, the product is finished with waterproof types of varnishes, with drying of each layer for at least 12 hours. Layers are put at least 3, smeared with a thick layer, trying not to leave gaps. Only after this, the rocking chair can be considered finished.

You can buy anything in modern stores. A little imagination, a mouse and a keyboard with Internet access, as a huge number of offers from social networks and online stores will fall on your computer. It also happens that financial position not the most prosperous, and purchases in online stores are considered luxury items. And sometimes you just want to do something with your own hands, they just itch. Here is a small selection of examples of how you can make some furniture with your own hands.

DIY bean bag chair

In the first example, we will see the manufacture of frameless furniture, the most popular item in stores today is a bag chair. A photo of the chair with your own hands is presented below.

Material costs for one bean bag chair are $40. This includes: polystyrene balls (filler), inner cover, outer cover.

First, the inner cover is sewn and filled with foam balls, then the outer one. Then just insert the inner cover into the outer one and you get a finished bag chair.

The most difficult thing is to collect the balls in a bag, they are trying to jump out of it, I had to use a vacuum cleaner. This is a short instruction on how to make a bag chair with your own hands.

DIY home chair

Now consider making your own ordinary home chair. Unfortunately, there were quite a few photos, there was no time to take pictures. The main stages were fixed in a timely manner, switching from a tedious workflow.

I wanted to get just an ordinary chair, and not just some incomprehensible rookery. To make it strong and stable, like store options. I had to look on the Internet for views and drawings of chairs in order to correctly assemble my design. I suggest you immediately look at the photos of the process of assembling the chair.

At the first stage, the basis-frame for the future chair is made in the form of a semicircle. Used chipboard with timber. The base of the chair is 10 cm thick. This will just be enough to fix the walls. And vertical racks have the same final function.

Hardboard was perfect for the back, and plywood for the front wall. All the curves and outlines of the future chair were drawn by eye from the remaining wallpaper. For the base, children's wooden cubes were used.

In the next step, I started gluing cardboard to fill in the interior space. In the process of work, even the glue had to be changed, the initially selected PVA did not fit. The walls swelled and became like a waffle, the glue was replaced with ordinary carpentry glue. turned out to be the most the best choice from all that is offered. There was even an idea for a rocking chair with my own hands, but I will implement the idea a little later.

After looking at the photo, you can immediately easily figure out how the finished walls were obtained. For leveling, I used an ordinary knife, the material is easily cut and deformable.

At the next stage, work with glue and foam rubber, glue the entire surface with a layer of foam rubber, do not leave any bald spots and uncovered places. On a monotonous surface it is necessary to sew a cover.

Well, we have reached the final stage, when we pull the cover and get a beautiful finished chair. The product turned out to be very heavy, but it will be completely safe for children, can be attributed to the pluses. As for the fabric used, nothing was bought anywhere. The scraps available at home and the remnants of sewing were used.

We wanted to get temporary furniture, no one planned to make a chair for centuries. The sieve on the armrests, despite a good tack with glue, will peel off over time. If you say a little about the design of the chair, then it turned out to be simply indestructible.

Chair made of plastic bottles

What people don't do plastic bottles. And rafts in their youth, and bird feeders in kindergarten. This material has excellent inclinations for creativity.

Plastic bottles are a real find; in ordinary life, brooches, scoops, curtains and buckets are made from them. They are used to decorate flower beds, lay them out instead of pipes, make a hanging chair.

We wanted to try to make a chair out of bottles, why not? At first it all started with great enthusiasm for collecting bottles, and then everyone unanimously realized that there was simply nowhere to store them in such quantity in a small home area of the room.

Even at the initial stage of storage, it immediately became clear that the necks of the bottles were not needed, more precisely, half of the bottles. We decided to stack them in blocks of two bottles, carefully cutting off the throat and fastening 2 pieces to each other. One was cut off the neck, turned over and inserted into the second bottle. Of course, a wooden chair looks much more attractive and solid.

For the complete manufacture of the chair, it took about 90 bottles to collect, they were fastened together with adhesive tape, and covered with stretch film on top. It will not work to talk about the entire process of assembling the chair; at the time of writing the article, the chair was ready.

In short, we can say that you should not regret attaching bottles of scotch tape, because. during assembly, they can simply diverge from each other, you will have to spend a lot of time in order to redo the structure later. In this regard, I had to resort to stretch film and finalize the chair to the final stage.