A DIY tool box is more practical than spending money at the store. DIY toolbox is more practical than spending money at the store Make your own toolbox

Reading time ≈ 5 minutes

A real owner always takes care of the safety of his tools. Even a small set should be stored in an orderly, neat manner. A skilled craftsman can assemble a container for tools and fixtures on their own. Below we will talk about how to make a tool box with your own hands. The presented photos and videos will help in the work.

Outwardly, the box looks solid and stylish, it immediately declares a serious approach to the life of its owner. Its dimensions (70x40x45 cm), i.e. 70 cm wide, 40 cm deep, 45 cm high. This is sufficient to accommodate hand tool. The drawer has 3 drawers, as well as a top hinged lid that opens up a spacious compartment. This box allows you to protect tools from dust, organize safe storage.

Required Tools

For the manufacture of wooden box you will need the following tools:

• a circular saw;
• milling machine;
• grinder;
• clamp;
• hammer;
• wire cutters;
• file;
• wood saw;
• chisel.

Step-by-step instructions for making a tool box

The optimal material for the manufacture of the frame is oak wood. This is an excellent durable material, which is durable and resistant to mechanical stress. It is better to take as a basis - glued boards with a thickness of 19 mm. This material does not have knots and rotten inclusions. With the help of a circular cut a strip 38 mm wide.

So that when gluing the individual elements do not move relative to each other, a carnation is driven into the first part a little, its cap is removed with wire cutters, and then a second board is stuffed onto the protruding sharp tip.

The boards are additionally coated with glue and fixed.

The glue that has come out at the joints of the parts is removed with a chisel, you just have to wait for the glue to dry a little.

The result should be a 38x38 mm part. Its butt is polished.

The edge must be cut strictly at an angle of 90 °, so cutting off the part desired length, we must not forget about the angle of the cut.

This technique will help to ensure the accuracy of the cut angle.

The location of each part is marked so as not to get confused during assembly.

A groove is cut in each part along the entire length, it must go strictly in the center.

The grooves can be made either with a stationary circular saw or with a milling machine.

On parts that are intended for the manufacture of vertical corner supports of the frame, transverse markings are made.

Another longitudinal groove is made in the rear corner parts. It is not needed in the front corner bearings.

For subsequent fastening in the end part of the blanks, you need to find the center, noting the point of intersection of the diagonals.

It is necessary to carefully check the compatibility of the blanks.

The blanks are processed with a file.

In a freely assembled frame, marks are made to subsequently lengthen the grooves.

The grooves are cut with a hacksaw for wood.

Remove all excess with a chisel.

These blanks are needed for drawers. A corner is sawn from the end part.

Each blank is drilled for bolting.

Observing accuracy, it is necessary to drill the prepared parts.

The part intended for fixing and dividing 2 drawers is cut out at an angle of 90°.

Having installed the details for the movement of the boxes in place and fixing them, they gradually begin to screw them.

The corners of plywood blanks are cut off, as in the photo.

The walls of the lower drawers are attached to plywood sheets with self-tapping screws.

Prepared horizontal plywood parts are attached to one side. First, this is done without the use of glue.

During fixation with clamps, it is necessary to check the diagonal so that the dimensions match.

Drawers are made from plywood.

The grooves can be cut either on a stationary saw or with a milling cutter.

Details of drawers are fastened with glue.

The side parts of the boxes must have grooves for movement along the planks fixed inside.

For strength, the side parts are fastened with dowels, which are cut flush.

For reliability when gluing, small carnations are partially driven into the surface of the front wall of the drawers, their caps are removed.

After attaching the front panels to the drawers, they look to see if the individual elements are evenly positioned.

When gluing, it is necessary to observe the utmost accuracy, there should be no gaps.

At the end, the top frame of the box is made of plywood.

To make a precise cut at a 45° angle, it is advisable to use a special tool.

The blanks for the frame are connected and fixed when glued using a tension belt.

There is always something to fix in the house. It could be a leaky faucet, a loose shelf, or a broken chair. Of course, for each of these actions, a man needs a special tool. As a result, this leads to the fact that a large number of self-tapping screws, hammers, wrenches and etc.

Where to put all the tools so that they are in one place and at the same time do not attract attention? Certainly, the best option there will be a box for tools, which can be purchased at the store or made by hand.

What are the boxes?

Hardware stores offer not only repair materials, but also special boxes in which it is convenient to store tools in a compact form. If there is no time and desire to make such a box with your own hands, then you can easily purchase it ready-made. However, it would be much better to do it yourself.

A homemade box will be direct proof that a man is a jack of all trades and can easily cope with any task.

Before buying or making at home, you should clearly determine the type of box that will be most useful. For this, its purpose is determined.

Irregular use does not imply the presence of a fancy design. Much better in this case, a simple box-box with one section is suitable. There is another type - an organizer box. It is more suitable for men who are constantly engaged repair work whether at home or in the workplace.

To do right choice should come down to personal preference. The choice of the box depends on the man himself and his ability and desire to make something.

How to make a box with your own hands in stages?

If it was decided to make the box yourself, then you need to have a step-by-step instruction, including a sequence of actions. It will allow you to accurately understand how to make a tool box without much financial and labor costs. Let's define the main stages of work:

Definition of a plan

This stage is very important, since the calculations obtained and the diagrams made will make it possible to draw up a prototype of the structure. If a mistake or error is made somewhere, then the final product may differ greatly from the intended one.

To depict a box in the form of a drawing, use paper and a pencil or a special program on a computer.

Work materials

It should be clear what materials will be used to create the future tool box. They are divided into mandatory and optional.

The latter depend on the specific case, and the mandatory group includes measuring devices, fasteners, a hammer, a hacksaw, etc.

Manufacturing process

The main work that will determine the outcome occurs precisely at this stage.

Manufacturing work

To understand the specifics of how to make a design yourself, let's give a simple example, which is shown in the photo of the tool box. The design is a box-box, which has a special handle for moving.

What is this box made of? Plywood, plastic or metallic materials. Their choice again depends on the personal preferences of the master. As a rule, most use coniferous trees for manufacturing. It's all about their availability. high quality and ease of processing.

Let's take a step-by-step look at the process of making a box-box:

• After a drawing is made on paper or a computer, it is transferred to the material that will serve as the basis for the design. That is, on wood, plastic or metal, details are drawn with a pencil, and then cut out with a hacksaw.
• The main elements of the box: walls (4 pcs.), Bottom. The simplest tool box may not contain a lid.
• As soon as all the parts are cut out, they are connected with glue and wait for drying.
• After a few hours, when the glue is completely dry, the joints are additionally fastened with nails or self-tapping screws.
• Installing the handle. As it is suitable rail made of wood.

By following these simple steps, you can get a great DIY tool box.

The finished structure is additionally coated with a varnish layer to add shine, beautiful appearance and protect the material from liquid ingress.

The presented box-box is considered the simplest, but it is very convenient. Following step by step instructions, even a beginner can make such a box with his own hands.

Of course, later you can make a more advanced and complex model, but for the first experience it is impossible better fit simple box.

DIY tool box photo

Tools should be in everyone's home. When there are too many of them, you can make a DIY tool box. This is an essential attribute for storing tools, because it is important that everything is in its place. In this case, you can store tools. You can take them with you if needed.

Figure 1. Toolbox drawing.

The materials from which the boxes are made

Tool cases can be made from various materials:

• plastic (very easy to transport, light in weight);
• metal (heavier, but have a solid construction);
• wooden (have a small weight, reliable design).

To make a box with your own hands, plywood is most often used. This is the simplest and most accessible material.

The main stages of work on the manufacture of a box of plywood

To make a case, you will need the following tools and materials:

Figure 2. Assembling the toolbox.

• circular saw;
• hacksaw;
• drill;
• chisel;
• roulette;
• clamps;
• plywood sheet;
• loops;
• screws;
• joiner's glue;
• finished pen;
• rubber strips required for screed;
• self-adhesive Velcro;

Before starting work, it is necessary to create a product design; the drawing can be made on paper or a computer (Fig. 1). Calculations are necessarily performed, the main dimensions are recorded. Next, all measurements should be transferred to a sheet of plywood. This can be done with a tape measure, regular ruler, pencil or marker. Blanks for the future design are cut along the drawn lines. It is also necessary to mark all the grooves, cut them on the blanks. All irregularities must be cleaned with a chisel. Thanks to the grooves, the design of the box will be stronger.

Figure 3. The handle for the tool box is attached with glue or screws.

The next step is the assembly of the structure. To glue the parts, you need wood glue. The main sides of the box are glued together. During gluing, they must be held very tightly. It is best to pull off the box with special rubber strips and do not remove them until the glue dries (Fig. 2). On the doors you need to round the corners.

In addition, the handle can be made from MDF. The layout is drawn on the tree, then cut out. After the handle is cut out, it is imperative to treat the surface, and then attach the handle with glue and screws (Fig. 3). If you don’t want to cut a handle out of plywood, you can buy it ready-made in the store. The main selection criterion is strength.

The next stage is assembly, fastening of the outer cover of the case, doors. You need to attach all the details, and then use a pencil to mark the place for the loops, fix them.

To attach the outer cover, you need to prepare a screw hole.

To organize the order in the box, you need to make small compartments. The components of the compartments are cut out according to the same principle as the box. Grooves are made, glued. A place for screwdrivers and other tools can be made on one side of the case. To do this, you need to make an insert with slots from plywood. Velcro can be glued to attach the cable and extension cords to another wall. You can take special Velcro on a self-adhesive basis or stick ordinary ones with hot glue. The final step is to fill the box with tools.

Making a box from a plastic canister

Figure 4. Instead of plywood, you can use plastic canisters to make a box.

If it is not possible to make a plywood tool case, you can use an ordinary plastic canister (Fig. 4).

Materials needed for work:

• plastic container;
• hacksaw;
• fasteners.

The container must be rectangular shape and with a handle located in the center. In addition, there should be a screw cap that will serve as a lock.

The process of making a box is quite simple. With the help of a hacksaw, the canister is cut in several directions. The first cut is made in the center of the neck and the handle of the container, the cork must be removed, and the upper wall must be sawn through.

The second cut is made in the horizontal direction. It must be done at the top of the canister, on the end sides. The container must be sawn from the upper wall at a distance of 3 cm, and on the sides - to a depth of 2 cm.

After the cuts are made, the canister can be opened. To do this, bend the side parts of the top cover with the halves of the handle. Here you can store a variety of materials for fasteners: nuts, nails, bolts, screws. The top cover must be closed by folding the handles together. Everything is fixed with a screw cap.

To make the box durable, additional locks are made on the end walls. Drill holes in the walls or cover, insert hooks, bolts with nuts into them.

DIY toolbox is quite easy to make. The main thing is to follow all the stages of work in order to get the right design.

By making a case yourself, you can save a lot of money.

Hello everybody!

A toolbox today is a very indispensable thing for every owner. Most of us have a lot of different tools that we may not use very often, but nevertheless, we keep them, since not one repair can do without them. In order for the tool to be in one place, and it was convenient to transport it, we use special boxes. Often we just buy them in the nearest store, the range and variety allows us to do this. But why not make it yourself? The manufacturing process is not too complicated, anyone should be able to handle it, especially with a handmade thing, which is much more pleasant to use than a purchased option. This article will describe 4 different ways production of boxes, a photo report is attached.

Let's start making!

Manufacturing Method No. 1

We will need:

Material

Plywood;
- pine board;
- nails;
- wood glue.

Tool

- drill;
- hammer;
- chisel;
- manual frezer;
- ruler;
- pencil;
- roulette.

First of all, you need to find necessary material, plywood or trimming boards are suitable for this. Further, according to the presented drawing, it is necessary to mark up, then cut out all the details of the case. It is necessary to make special grooves into which the partition will be placed, for this we use a manual milling cutter, or another available tool.

The diagram shows the following body parts:

1 - wall (2 pcs.);
2 - sidewall (2 pcs.);
3 - bottom;
4 - groove along the thickness of the partition and a depth of 1/2–1/3 of the thickness of the material

When everything is ready, all elements of the box body should be sanded. Next, we assemble the body together, fix the parts with wood glue, and then additionally fasten with small nails.

Now we make a partition for the box, cut out a special handle, for this we use a jigsaw.

When the partition is ready, grease the grooves with wood glue and install it in its place.

Next, from the planks we make overhead handles, with the help of a planer we round the corners. Then we make tool holders from the rails, use a jigsaw, and a drill. The holes will serve for screwdrivers, and pliers, etc. will be installed in square cutouts. tool.

So that the box does not get dirty, and there is protection from environment, varnish the surface. As a result of the work done, we get such a homemade box.

Manufacturing method No. 2

Drawer-stool

Material

Plywood or OSB;
- wooden beam;
- self-tapping screws;
- wood glue.

Tool

Available cutting tool;
- screwdriver;
- ruler;
- pencil;
- roulette.

We take an existing sheet of plywood, make markings on it, and, according to the dimensions presented, cut out the lid (Fig. 1), then the longitudinal drawers (Fig. 2) and sidewalls (Fig. 3).

Next, we take a wooden beam with a section of 40x50 mm, cut out a handle, and 4 legs with bevels at the ends at an angle of 15 °.

Next, we assemble the structure together, using self-tapping screws as fixing elements.

Parts layout:

1 - cover;
2 - tsarga;
3 - handle;
4 - leg;
5 - sidewall.

When everything is ready, using sandpaper or grinder round sharp corners and clean the surface. Next, you can apply a protective coating.

The end result should be such an unusual tool box, which, if necessary, can be transformed into an ordinary stool, for this it is enough to turn it over and put it on its legs, with it it will be convenient to reach the place we need, at a time when growth does not allow it.

Manufacturing method no. 3.

Box for the young master.

Does your child love to craft? We offer to make a small box with him, where he will store his favorite tool.

To make a box with our own hands, we need the following

Material

16 mm boards;
- round wooden beam;
- self-tapping screws;
- wood glue.

Tool

Available cutting tool;
- screwdriver;
- ruler;
- pencil;
- roulette;
- clamps.

First you need to take the existing boards with a cross section of 16 mm, then we make the markup, according to the dimensions provided, after which we cut the wood into the component parts we need.

The drawing shows the following details:

1 - sidewall;
2 - bottom;
3 - handle;
4 - handle stand;
5 - holder.

Using sandpaper, we grind the surface and remove sharp corners. When everything is ready, we begin to connect all the parts together, first you need to connect the bottom and sidewalls, then we put vertical racks along the marked lines and at the same time we put a horizontal handle.

We fix everything with glue and screws. Then we install special holders for screwdrivers.

Now you can paint, choose the color and coating at your discretion.

The toolbox is ready.

Manufacturing Method No. 4

The next version of the tool box is well suited for carrying various and necessary equipment for us, its appearance will be distinguished by solidity and reliability.

To make a box with our own hands, we need the following

Material

The board is not thicker than 12 mm;
- self-tapping screws;
- joiner's glue;
- pen;
- corners 8 pcs.;
- latch 2 pcs.;
- loop 2 pcs.

Tool

Available cutting tool;
- screwdriver;
- ruler;
- pencil;
- roulette;
- clamps.

For the manufacture of the box we use such wood as: pine, linden or poplar. Most optimum thickness boards will be 12 mm thick.

Next, we make the markup, according to the indicated dimensions in the drawings, after which we cut it into its component parts, as shown in the photo.

Full list of required parts.

In order to make sure that the wood was cut correctly, you need to put all the parts in a single box.

First, we assemble the bottom part and the lid of the box, for convenience we use clamps and corner clamps. We fix the parts together with carpentry glue.

Then, using a drill, we drill a hole for the self-tapping screws, we drill the holes.

A good owner will always have a whole arsenal of tools at hand: from nails and screws to pliers, a level and a set of screwdrivers, not to mention a drill, puncher and screwdriver. Very often, simple household repairs do not start in any way due to the fact that the master cannot find all the tools he needs in the apartment or garage. To prevent this from happening, all working tools must be stored in a specially designated place - a tool box.

What are the tool boxes, what requirements do they have to meet, and how to make a tool box with your own hands - this is an article about this.

Varieties of tool boxes

In fact, a tool box is a box with or without a lid, divided into several compartments of various sizes and shapes. Small drawers are designed to store fasteners, they can contain drills, tips, or other small parts. As a rule, such boxes are divided into several compartments, each of which has a separate lid. Such boxes are easy to carry, because they weigh a little.

Larger cases are needed to store and transport large tools such as hammers, saws, drills or jigsaws. Quite huge boxes will be needed to contain perforators, levels or mallets. These tool boxes are often made on wheels so that they can be moved and transported.

Professional toolboxes can differ depending on the skill of the craftsman: so a plumber needs one set of equipment, and an auto mechanic needs a completely different one. You can find such boxes in building supermarkets or in specialized stores, they are often sold complete with the tools themselves.

The cases are divided into several categories. This takes into account not only their size, but also the design, as well as the material of manufacture. Structurally, it can be:

• Open boxes with handles for large tools and easy transfer from one place to another.
• Multi-tiered boxes with many small and large compartments for complex storage of working parts and their facilitated transportation. Such a box can be thrown into the trunk of a car or carried by hand.
• Compact cases with ergonomic handle containing all the tools needed for minor repairs or country trips.
• Chests of drawers, consisting of several drawers, as a rule, are used permanently at the place of work.
• Tool belts are needed for those who work at heights or in hard-to-reach places.
• Trolleys are a kind of tool boxes on wheels, which are large in size. On such devices, very large equipment is moved, such as welding machines, drills.

Important! When choosing a box for your tools, it is better to give preference to multifunctional boxes, where each part has its own place, and small compartments are closed with lids. Otherwise, all the tools run the risk of being mixed into one heap during transportation.

What are tool boxes made of?

Cases and boxes can be made from various materials, but the main requirement for them is the same - the boxes must be light, since the tools themselves weigh quite a lot. There are a few more nuances that you need to know about those who buy a case for their arsenal of tools:

• The bottom of the box should be as thick as possible, since it is on it that the entire mass of the contents presses.
• A full box should not deform when lifted - the walls remain perpendicular to the lid and bottom. If the walls sag, this indicates that the strength of the case is insufficient for such a set of components.
• Well, if the material of the box is fire-resistant, then expensive tools will survive even during a fire.
• If there are gaps in the box, dust and construction debris will enter the box and contaminate the tools. And in this case, the contents are threatened with oxidation and rust due to high humidity.
• Durability is an important factor, because a professional box costs quite a lot, and the load on it from metal components will be significant.

Today, the most popular materials for such boxes are:

Attention! All materials must comply with special standards, because if the box breaks at the most inopportune moment, all heavy tools will fall on the feet (or on the head) of the unfortunate owner.

If you can still make a metal or wooden tool box with your own hands, then you can really only buy plastic boxes.

How to make a DIY tool box

If the owner has decided to make a box for his inventory on his own, first of all, he needs to determine the size and choose the design of the box.

To do this, you need to inspect all your tools, measuring the most dimensional elements and taking into account small things (bolts, nuts, washers, etc.). According to these parameters, the dimensions of the container itself and the internal compartments are calculated.

Tool box design

Speaking about the design of the boxes, they do not mean their shape, but the way they open and the presence of additional sections. The following designs are considered standard:

• Case - a portable rectangular box with a handle. As a rule, cases are divided into many departments, have removable partitions that allow you to independently divide the space inside the box. The weight and dimensions of such cases are usually small.
• Container - a larger box for a variety of tools. As a rule, it has the shape of a trapezoid with a rectangular bottom. Inside this box there are also partitions, and there may be separate smaller boxes (folded like a nesting doll). Sections of such a container can be pulled up and to the sides, forming a whole "trellis" with tools and fasteners. Large tool boxes of this type can be equipped with wheels, which is very convenient and practical.
• Multiboxes are arranged vertically and the drawers in them are pulled out along the guides, as in a regular chest of drawers.

With your own hands, it will be easiest to make a case for tools, because in this design there are no complex mechanisms and hinges with which additional sections come out.

Important! Although it is quite possible to build a container with boxes that fold over several floors with your own hands. To do this, each pair of "floors" should be fastened with metal brackets, providing mobility to the elements (as in the figure below).

Bringing an idea to life

Speaking of material for self-manufacturing box, then, of course, the easiest way to work with a tree. For the first experience, it is better to choose inexpensive wood - a planed coniferous board is quite suitable for boxing.

The whole process of making a tool box consists of several stages:

1. Make a drawing of the future boxing. To do this, use a regular drawing paper and a ruler or a professional program such as AutoCAD.
2. The resulting drawing is transferred to the wood with a simple pencil or marker.
3. Cut out the details along the contour using a jigsaw or saw.
4. The tree is treated with antiseptics or stains to prevent it from rotting and to make it “inedible” for insects and rodents.
5. The box is being assembled. Now all the details need to be connected into a single structure, according to the drawing. To do this, it is best to use wood glue, which is applied to the ends of the parts and pressed against each other for a few seconds.
6. It is better to additionally fix the elements of the box with self-tapping screws, making sure that the wood does not crack when screwing in the fasteners.
7. Install the lid using conventional hinges or another device appropriate for the type of drawer opening.
8. The lid is equipped with a handle for carrying and transporting the box with tools.
9. Inside the box is marked into sectors, given the diagram and drawing. Additional partitions are cut out of the board and fixed in place with glue and self-tapping screws.
10. The walls, bottom and lid of the box are sanded with several types of sanding paper, then painted or coated with several layers of varnish.

The box is ready to use, it remains only to fill all its compartments with the appropriate tools and fasteners.

The simplest tool box

Beginners in carpentry are offered more than simple design box for tools - an ordinary box with a handle, but without a lid. The advantage of such a box is that it is suitable for tools of various sizes, if desired, even a water level or a puncher can be placed here, or you can make a miniature box for an “apartment” master.

Such a box consists of only six parts:

• two long side elements;
• two short sides, the height of which should exceed the height of the long sidewalls, since the handle will be attached here;
• bottom, which should be made of whole piece wood, since it is the bottom that takes the load from the weight of the tools;
• handle, the role of which can be played by a bar, plank or piece round section- the choice depends on the size of the box and the estimated weight of its contents.

If desired, the design can be supplemented with internal partitions or complicate it with compartments with lids or doors.

All elements are assembled into one structure, fixed with carpentry glue, then additionally fastened with self-tapping screws. Particular attention should be paid to the fasteners of the handle - it must be strong and reliable.

You can independently assemble a tool box not only from boards, depending on the arsenal of tools, plywood, chipboard, OSB, galvanized metal or aluminum sheet can be used.

There is nothing complicated in the manufacture of such a box, and the advantages of the product are obvious: tools and fasteners will be in a certain place, at any time it is enough to get the box from the pantry or garage and make the necessary repairs.