Flexible floor plinth for columns and not only made of composite material. Working with a ceiling plinth How to attach a plinth to a round corner

IN modern apartments and houses, the corners are often not straight, but rounded. This somewhat complicates the installation of the plinth. However, there are special technologies that can be used to bend both wooden and rigid plastic or even foam models.

In addition, a flexible floor or ceiling plinth made of soft plastic, polyurethane and even rubber is being sold today. If you don’t want to bother with bending the planks, you can purchase just such an option or order a radius one.

How to bend the floor plinth?

So, you do not want to use a flexible polyurethane floor skirting board or a model made of some other similar elastic material, but prefer to install a regular wooden or plastic one. The manufacture of a semicircular version for the floor in this case is usually entrusted to a specialist. However, you can try to round the desired bar yourself.

For installation on curved walls, rounded decor is used

How to round wood planks

In order to bend a wooden plank, it is pre-steamed. Water is poured into the basin and put on fire. The plank should warm up and steam over a jet of steam for half an hour. How to bend a wooden skirting board:

You can round the bar by hanging it and securing some kind of load on both sides;
Sometimes a special device is used:

You can round the element on a special device

You can also attach two bars to the floor at a certain distance from each other and insert a plank of wood between them.

Important: Great care must be taken when using this method. If one of the ends of the element slips out of the support, it will fly off and may injure you.

How to round a very hard wood skirting board? In this case, the bar, most likely, will have to be cut into several pieces, fixed to the wall and mounted transitions between them.

If it is not possible to bend the plinth, it must be cut into pieces

How to round a hard plastic model

Now let's see how to bend the plastic baseboard. You can round it according to the technology described above for wood. Sometimes they also use a slightly different method. At the same time, with reverse side planks are notched. Then it is heated with a building hair dryer.

Plastic models can be rounded in the same way as wooden ones.

Important: The heated bar must be rounded and immediately installed in place, without waiting for the material to cool. When doing this, be careful not to break it.

How to bend a fillet for a ceiling

If you do not want to use a flexible ceiling plinth, you can try bending the foam or polystyrene foam.

Semicircular ceiling plinth also has to be used quite often

The foam baguette should not actually be bent, but rounded very carefully, squeezing in small sections. After the non-flexible brittle fillet will take desired shape, it is smeared with glue and pressed tightly against the surface of the wall, securing it with small carnations for reliability.

You can bend the foam model by gently crushing along the length

In order to make it clearer how to round the foam, we suggest you watch this video:

How to make the plinth a semicircle if the bending arc has too small a radius? At the same time, a foam fillet, like a wooden one, is cut into several pieces, which are mounted on a curved corner.

Pieces of foam fillet

Important: The joints between the pieces must be passed with putty or white silicone sealant. Next, the seams are carefully sanded. The resulting plinth radius can be painted with white or colored paint.

Flexible floor and ceiling decor

Rounding the baseboard at home, without having some experience, is still quite difficult. It is easier to complement the floor finish using a bendable skirting board.

Flexible plinth floor or ceiling bend very easy

There are several varieties of them:

Rubber. May have very bright colors;
Cork flexible;
Soft flexible PVC plinth. For round wall fit Not bad. Sold wound on bobbins;
Liquid tree. After some time after installation on a curved surface, it hardens, retaining the resulting shape.
Flexible polyurethane skirting board. May have a variety of colors. A flexible polyurethane version for painting is also on sale.

Flexible polyurethane ceiling skirting is very easy to bend

How exactly to mount the plinth on a corner, if it is rounded, or on a column, of course, is up to you. If you are confident in your abilities, buy a regular hard decor and try to bend it. If you don’t have enough experience, get flexible skirting boards for the floor or ceiling.

When installing skirting House master sometimes faces the following problem: how to bend a skirting board to finish a curved surface? With a rigid plinth, this is almost impossible to achieve.

PVC plinth, although considered flexible, is not so easy to bend without pre-treatment - there is a risk of breaking the product. Next, consider how to bend a PVC skirting board.

Necessary tools and materials for work:

large pot of water
rope, twine or cord;
wooden bars;
nails, hammer.

Work performance technology

Before, it should be steamed and heated to + 70 ° C.

Pour water into a large saucepan and put it on fire, bring the water to a boil.
We will hang the plinth over a jet of steam, so it will heat up and steam for at least 20-30 minutes.
After the plinth has steamed out, you can already begin to bend it using one of the following methods:

We hang the plinth horizontally, fixing it in the middle, we tie a load to its edges, which will give the plinth the desired shape
On a certain plane, we draw a line corresponding to the desired shape of the plinth, along it we nail several wooden bars. Thus, we get a certain curvilinear shape. Then we insert the steamed plinth between the bars and securely fix it.
We give the baseboard the opportunity to dry and cool, after which it will become hard.

Alternative ways

, flexible.
Soft molding and plinth tape made of PVC.
Flexible plinth floor made of cork, semicircular, bent.

Flexible polyurethane plinth has an optimal combination of price and quality, it is used quite often. Skirting tape is relatively inexpensive, but it is capricious in installation and not every type of glue is suitable for it. It is often used in the bathroom. Flexible floor plinth made of cork is the most expensive of these three types, but the naturalness of the material and excellent appearance speak in its favor.

Flexible plinth, floor, cork

The final part of any work on laying flooring is the installation of a skirting board around the perimeter of the room. The article will focus on such an original category of this decorative element, as a flexible plinth for the floor: its features, advantages, varieties and installation methods.

Plinth and its features

In principle, the decorative strip itself, limiting the flooring, is a product that emphasizes the design and aesthetics of the laid material. Also, using a skirting board, you can mask any differences in the heights of the laid flooring and defects associated with installation errors, hide electrical and telecommunications wiring, etc.

In the photo and during visual inspection, these elements can both imitate the expansion of the floor covering, and be a separator between floor and wall coverings.

Initially, the most primitive wooden plinth was presented on the construction market, characterized by increased strength and lack of flexibility, which did not allow the product to be tightly joined to the wall. This, of course, was not a shortcoming of the plinth.

Rather, the problem was that the walls were not perfectly level. After installing such decorative strips, it was necessary to spend a significant amount Money for the purchase of compounds for sealing cracks and devices for removing bulges.

After the manufacturers launched such a product as a flexible floor plinth on the construction market, the problem was eliminated, since it is quite easy to install, and the unique design allows you to repeat any wall irregularities.

The number of creative solutions for combining skirting boards and flooring is greatly expanded, since there are at least two types of flexible decorative strips: plastic or cork.

Calculation of the amount of plinth for the purchase

Work begins on the installation of flexible skirting boards with the fact that calculations are made desired length planks that are part of the prefabricated structure. In fact, the length of a solid plinth is determined, which will be equal to the perimeter of the room with some margin for installing various connecting elements for joints and corners.

All measurements are made with a tape measure. Only doorways do not count towards the total length. As a result, the resulting value is divided by the length of a single bar. When receiving a non-integer number of slats, their number should be rounded up.

Selection of skirting boards and auxiliary structural elements

The main parameters that should be relied upon when choosing skirting boards:

color - there are many options for coloring skirting boards, which allows you to create a huge variety of combinations between floors and walls in the room;
design features - they mainly consist in the presence or absence of a cable channel for laying electrical and telecommunications wiring (more: "");
form.

When considering a bendable floor skirting board with cable channels in a store, it is necessary to make a choice in favor of prefabricated structures. Having disassembled such a plinth, you can easily repair the cables and return the structure to its original form.

To hide various irregularities near the junction of walls and floor, you can use a soft plastic plinth with flexible edges. The name makes it clear that the edges of the plank fit perfectly with any surface.

To determine the exact number of connecting elements for high-quality installation of skirting boards, it is necessary to draw a schematic plan of the room (on a scale) with the exact application of all joints and corner joints.

The following nuances will allow you to carry out this procedure qualitatively:

it is worth distinguishing between the corners used for joining planks on the outer and inner corners of the room;
plugs at the ends of the plinth are left and right;
no matter what the calculated length is, it is necessary to purchase skirting boards with a small margin. Naturally, this will create some additional costs, but it will help to avoid additional time spent going to hardware stores if some items are not enough.

Mounting tools

For quality installation soft plinth for the floor, you must have the following tools with you:

measuring device of great length;
sharpened knife;
joiner's clamp (miter box) for trimming planks;
putty knife;
rags;
drawing devices for marking;
foam sponge;
tools for fixing finishing elements. This item is determined by the selected installation method. It can be either a special binder mixture or traditional fasteners: self-tapping screws, nails, etc.

Features of laying flexible skirting boards

To date, there are several basic ways to mount a flexible skirting board. As mentioned above, you can use glue, self-tapping screws, as well as various fastening systems during installation.

Directly flexible plinth is bent in any way. The integrity and quality of the skirting boards do not deteriorate. If you understand how to bend the floor plinth, then there will be no difficulties during installation. With the help of such elements, you can round the corners and increase the comfort of the interior.

Between the plinth and flooring sometimes you need to make a minimum clearance. Its dimensions are selected based on what materials and skirting boards are used. For example, when laying tiles, you can not make such a gap at all, and in the case of laminated panels or parquet board it is simply necessary and should be at least 5 millimeters.

The reason is that these materials can expand when the temperature in the installation room rises. Naturally, the collision of the coating with skirting boards or walls can cause various deformations.

Mounting on adhesive mixture

This technology is considered the simplest and cleanest, since there is no need to drill various holes and produce any complex installation work. As fasteners, ordinary liquid nails or adhesive composition. The selected adhesive mixture does not affect the installation procedure.

The procedure looks like this:

The perimeter of the room is measured to calculate the required length of the plinth. It is best to mark up immediately.
The plinth is covered with an adhesive mixture with inside. Plugs and connectors are lubricated in the same way.
The coated plinth is pressed against the wall, then it is torn off and held for a minute. Then he is again pressed against the wall and held for some time. Usually, the period of primary solidification of the adhesive mixture is indicated on the packaging. At the same time, the skirting board itself must be leveled in accordance with the section of the wall on which it is fixed. Any excess glue that has appeared outside the plinth is promptly removed with a rag. Of course, such work will be better done with an assistant.

If installation is carried out in areas with large bends and arcs, then it is worth knowing a number of important features of the process. The biggest problem is that in such areas a large pulling force is applied to the plinth, and then it simply may not hold on to a poorly dried adhesive mixture.

The problem is solved quite simply: you should additionally fix the plinth with masking tape, which is removed after the composition used during installation has completely dried.

Self-tapping mounting

This installation technology is one of the most reliable, but its disadvantage is the low aesthetics of decorative strips upon completion of work. The reason is that places with fasteners screwed into them are visible in the photo and during visual inspection. Eliminated this shortcoming exclusively through additional costs for special camouflage plugs.

Installation is carried out as follows:

Holes with a diameter of about 2 millimeters are drilled in the plinth every 40-50 centimeters.
Then the holes are countersinked with a special cone-shaped drill so that the heads of the screws can be sunk below the surface of the bar itself.
The installation of panels begins from one of the corners of the room.
The bar is pressed against the wall and marks are made on it with a pencil to understand exactly where the screws will be screwed. Holes for dowels are drilled in these places.
A plinth is laid over the installed dowels and self-tapping screws are screwed into the pre-prepared holes.

When screwing in self-tapping screws, it is worth remembering the increased flexibility of the plinth, because it cannot be crushed much. It is also worth checking that it is pressed against the wall as much as possible without bends.

In the future, the actions are repeated according to the algorithm described above, and decorative plugs are put on each hole with a self-tapping screw. So that they do not fall out, you can put each on glue. In the same way, the connectors are fixed at the corners of the room and the ends of the plinth.

Mounting with special fasteners

Today, construction stores can offer their customers not only glue and self-tapping screws, but also special fasteners for skirting boards. Their advantage lies in the ease of installation and the possibility of dismantling with re-installation in another place.

The disadvantage is that installation can only be done on perfectly flat walls and floors. Naturally, the costs of time and effort increase. Also, fasteners can lose their strength and rub over time, which will reduce the overall stability of the structure. The latter applies only to those situations where the fasteners are removed and installed regularly.

Installation is carried out as follows:

As in the previous methods, markings are made directly on the walls of the room.
Holes of 2-3 centimeters are drilled at the marked fastening points.
In prepared places, plastic dowels are installed. Screws are screwed into them, on which the fasteners described above will be fixed. It is worth observing the interval between fastenings of 30-50 centimeters. The first fixing point of the panel should be no more than 10 centimeters from the corner of the room.
Directly mounting on screws can be put on several different ways. It is necessary to study the instructions provided by the manufacturer.
Each panel is mounted in the same way.

Installation of cork flexible skirting boards

Above, we were talking exclusively about flexible plastic skirting boards, but there are also more expensive cork products on the construction market. They are considered more reliable and safer, since they use environmentally friendly material in their production.

Their installation is carried out as follows:

The surface of the plinth is covered with a transparent varnish. The material can even be tinted if a dye is added to the varnish. The material should be applied with a parallel sponge, which will ensure an even distribution of the material over the entire surface. The drying time of the varnish must be checked with the sellers or the manufacturer.
Dried planks are cut and joined around the entire perimeter of the room. In order for the cuts to be perfectly even, it is necessary to fix the planks in the miter box.
Each element after docking is marked so that further installation is carried out in a clear sequence of elements. The first element in order is smeared with an adhesive mixture using a machined spatula and glued to the wall.
Each next element is mounted in the same way.

Checking yourself upon completion of work is quite simple. A well-laid plinth should look like a single, perfectly even line that outlines the entire room around the perimeter. It should be interrupted only at the jambs of the doorway.

Outcome

The article describes in detail the installation procedure various kinds floor flexible plinth. If you follow the instructions for choosing and fixing this decorative element, then there should be no difficulties. Naturally, you can always turn to professionals who will take responsibility for all stages - from purchase necessary materials prior to installation and commissioning.

Frame the room well rectangular shape. But what if you have a non-standard room: with columns, semicircular walls, or stretch ceiling complex configuration?

A flexible floor and ceiling plinth is suitable for you. With their help, you can hide minor flaws in the repair, uneven surfaces, as well as frame round structures.

You will learn about the varieties of flexible skirting boards, how to bend and fasten them from this article.

Flexible baguettes: their features

If the design of your apartment provides for semicircular or non-standard decor elements, you will need a flexible ceiling plinth. It will not only decorate the ceiling, but will perfectly decorate suspended round structures, hide defects and irregularities at the junction of the ceiling and walls.

Flexible skirting for the ceiling will emphasize all the advantages of the room

Sharp corners can cause anxiety and aggression. If you decide to create a calm atmosphere in the room, give the room softness - use a semicircular skirting board in its design.

Curved plank options

How to bend floor and ceiling moldings

Many people in the process of repair have a reasonable question: how to bend the plinth to give it the shape of a circle? Depending on the material of manufacture of the baguette, it can be bent in several ways:

making several cuts on the back side of the fillet. After that, they try to see if the baguette bends. If necessary, make additional incisions to bend the product;
cutting into small pieces, and combining them on a semicircular profile;
by heat treatment. The product is heated with a building hair dryer, bent, and then cooled in cold water to secure the bend;
the formation of a semicircle by cutting off the stiffeners from the back of the product.

Advice: most easy ways to bend the straps are the first and fourth, the rest are more laborious, require special skills.

Semicircular plinth radius in the interior

Materials for the manufacture of flexible fillets

For framing ceilings, polyurethane baguettes are most often used. Flexible polyurethane skirting board can bend in any direction. The product can be tried on several times, decorated with semicircular elements - columns, arches, bay windows.

Plinth floor polyurethane flexible will beautifully decorate the ceilings in a semicircle

Remember: polyurethane products bend better than foam plastic products.

How to round a wooden baseboardso that it does not crack? To do this, it must first be steamed. After half an hour of being over hot steam, the wooden baguette will become malleable for transformation. When the product bends and takes the desired shape, it must be fixed until completely dry. This can be done by imposing a load, or by making a special form.

Rounding a plank of wood - bending along the radius

How to bend a plastic skirting board? By heating with a hair dryer or hot water, you can also bend a PVC baguette. Under the influence of temperatures above 80 degrees, it will become supple and soft, able to take any shape.

A curved PVC floor baguette is attached to glue or self-tapping screws in a circle, plastic components are installed at the corner and joints.

PVC product, an example of how to make a semicircle skirting board

Advice: when heating the fillet with a hairdryer, be careful not to overheat the product so that it does not deform.

Special bending fillets for ceiling and floor

The simplest type of semicircular frame is a flexible PVC tape. It is self-adhesive and can be folded in half to form an even angle.

Tape products are produced in different color scheme, this is the perfect skirting board for a round wall

If you need a quality bendable skirting board, then good decision there will be a composite wood-filled edging. It is manufactured using the latest technology by injection molding and pressing.

Flexible plinth for wood-filled floor

An innovative product for decorating round elements is a flexible PVC floor skirting board. It is not exposed to ultraviolet radiation, moisture, solvents, does not burn and can different colors. These baguettes bend perfectly and therefore are suitable for columns, framing of semicircular podiums, bay windows.

Soft plastic baguette bends smoothly

To form a curved shape, the product is heated to 70 degrees, and then they begin to smoothly bend along the required radius. In case of hardening, it is heated in hot water and continue the edging of a semicircular shape.

non-standard design solutions will help to realize a flexible cork edging. Fastening to the walls is carried out with glue, which allows you to bend around even round columns.

Flexible floor plinth made of cork

Outcome

If there are columns, bay windows, semicircular ledges in the interior of the room, then you can use ready-made bending skirting boards to frame them, or bend the floor and ceiling edging yourself. A flexible frame will add style and softness to the room, make it more cozy, individual, and comfortable.

Perfectly frame a rectangular room. But what if you have a non-standard room: with columns, semicircular walls, or a stretch ceiling of a complex configuration?

A flexible floor and ceiling plinth is suitable for you. With their help, you can hide minor flaws in the repair, uneven surfaces, as well as frame round structures.

You will learn about the varieties of flexible skirting boards, how to bend and fasten them from this article.

Flexible baguettes: their features

Flexible skirting for the ceiling will emphasize all the advantages of the room

Sharp corners can cause anxiety and aggression. If you decide to create a calm atmosphere in the room, give the room softness - use a semicircular skirting board in its design.

Curved plank options

How to bend floor and ceiling moldings

making several cuts on the back side of the fillet. After that, they try to see if the baguette bends. If necessary, make additional incisions to bend the product;
cutting into small pieces, and combining them on a semicircular profile;
by heat treatment. The product is heated with a building hair dryer, bent, and then cooled in cold water to fix the bend;
the formation of a semicircle by cutting off the stiffeners from the back of the product.

Advice: the easiest ways to bend the planks are the first and fourth, the rest are more time-consuming, require special skills.

Semicircular plinth radius in the interior

Materials for the manufacture of flexible fillets

Most often used for framing ceilings. Flexible polyurethane skirting board can bend in any direction. The product can be tried on several times, decorated with semicircular elements - columns, arches, bay windows.

Plinth floor polyurethane flexible will beautifully decorate the ceilings in a semicircle

Remember: polyurethane products bend better than foam plastic products.

How to round it so that it does not crack? To do this, it must first be steamed. After half an hour of being over hot steam, the wooden baguette will become malleable for transformation. When the product bends and takes the desired shape, it must be fixed until completely dry. This can be done by imposing a load, or by making a special form.

Rounding a plank of wood - bending along the radius

How to bend? By heating with a hair dryer or hot water, you can also bend a PVC baguette. Under the influence of temperatures above 80 degrees, it will become supple and soft, able to take any shape.

A curved PVC floor baguette is attached to glue or self-tapping screws in a circle, plastic components are installed at the corner and joints.

PVC product, an example of how to make a semicircle skirting board

Advice: when heating the fillet with a hairdryer, be careful not to overheat the product so that it does not deform.

Special bending fillets for ceiling and floor

The simplest type of semicircular frame is a flexible PVC tape. It is self-adhesive and can be folded in half to form an even angle.

Tape products are available in different colors, this is the perfect skirting board for a round wall

If you are looking for a high quality, flexible skirting board, then composite wood-filled edging is a good solution. It is manufactured using the latest technology by injection molding and pressing.

Flexible plinth for wood-filled floor

An innovative product for decorating round elements is a flexible PVC floor skirting board. It is not exposed to ultraviolet radiation, moisture, solvents, does not burn and comes in different colors. These baguettes bend perfectly and therefore are suitable for columns, framing of semicircular podiums, bay windows.

Soft plastic baguette bends smoothly

To form a curved shape, the product is heated to 70 degrees, and then they begin to smoothly bend along the required radius. In case of hardening, it is heated in hot water and the semicircular edging is continued.

Non-standard design solutions will help to realize a flexible cork edging. Fastening to the walls is carried out with glue, which allows you to bend around even round columns.

Flexible floor plinth made of cork

Outcome

If there are columns, bay windows, semicircular ledges in the interior of the room, then you can use ready-made bending skirting boards to frame them, or bend the floor one yourself. A flexible frame will add style and softness to the room, make it more cozy, individual, and comfortable.