What is the zero level, why is it introduced. Zero level in the apartment. What is zero level in construction

The zero level can be compared with the waterline of a ship, only it is in full view of everyone and everyone understands why it is needed. From the name it seems to be clear why, but where and how it appears is not clear. The main task in preparing for leveling the floor with a dry or concrete screed is to reach the zero level over the entire area of the apartment. The floor, in the end, should be one parallel to the horizon, a perfectly flat surface.

What is the zero level in the apartment? How to conduct a zero level

Put a mark at the highest point of the relief in the apartment.
We duplicate this mark strictly horizontally on all other walls in all rooms in the apartment. To do this, it is best to use special tools - building levels.
Then you need to connect all the points, and then you get a zero level, and you need to level on it when performing a floor screed.

The choice of mark: from 10 to 100 mm is added to the highest point, how much is added depends on the type of screed used. From 30 to 50 mm is added with a dry screed, and there are restrictions, the minimum thickness is 30 mm, the maximum is 50 mm, if several layers of a prefabricated base are used, then 70 mm. For a wet screed, the additional length can vary from 10 to 100 mm - it all depends on the specific conditions.

And there are different technologies screeds: you can apply a concrete screed over a layer of large expanded clay, you can lay plywood on concrete base. different ways differently good.

How to coordinate rooms by level.

When the apartment has the same floor covering, then the screed is made under the same level. But often, for example, laminate flooring is laid in the room, tiles in the corridor and bathroom, because of this, it is necessary to coordinate the premises in terms of level before laying the final floor covering.

It's simple: to determine the height of the screed in each room, you need to count all the layers of the future floor covering and subtract them from the final level. Although everything is simple, but if this is not done at the preliminary stages of apartment renovation, then the floor with steps is provided to you.

Zero level markup methods

water level.
The most affordable and easiest way is to beat off the zero point of the room with a water level - a spirit level. Two glass tubes with water connected by a long hose allow you to measure not only the levels in one room, but throughout the entire dwelling.
Plus:
Ease of use.
Small tool price.
Minuses:
One person is not enough to measure.
Accuracy depends on the condition of the tool: the hose must not be kinked, air must not enter, etc.
Auxiliary level method.
At an arbitrary height, we draw a horizontal line and measure the distance to the floor after a certain distance. The more marks, the higher the measurement accuracy.
Pros:
Versatility: can be used for any horizontal and vertical surfaces.
One person is enough.
Minuses:
Lots of measurement samples to achieve an accurate result.
If there are erroneous measurements, then measurement errors accumulate.
Laser level
To be more precise, the measurements do not use a laser level, but a laser level. The method is based on the principles of the laser level, that is, the line outlined by the laser beam in space is the desired level.
Pros:
The most accurate measurements.
One person is enough to measure.
Minuses:
The high price of the tool.
The possibility of measurements depends on the conditions in the apartment, problems may arise with strong illumination or with a lot of dust in the room.
Bottom line: all methods are good if you apply them when necessary. The result will be on high level, especially if you arm yourself with a high-quality and serviceable tool. We do home repairs for ourselves, so the result, as a rule, is at a good level.

The zero level can be compared with the waterline of a ship, only it is in full view of everyone and everyone understands why it is needed. From the name it seems to be clear why, but where and how it appears is not clear.
The main task in preparing for leveling the floor with a dry or concrete screed is to reach the zero level over the entire area of the apartment. The floor, in the end, should be one parallel to the horizon, a perfectly flat surface.

What is the zero level in the apartment? How to conduct a zero level

Put a mark at the highest point of the relief in the apartment.
We duplicate this mark strictly horizontally on all other walls in all rooms in the apartment. To do this, it is best to use special tools - building levels.
Then you need to connect all the points, and then you get a zero level, and you need to level on it when performing a floor screed.
The choice of mark: from 10 to 100 mm is added to the highest point, how much is added depends on the type of screed used. From 30 to 50 mm is added with a dry screed, and there are restrictions, the minimum thickness is 30 mm, the maximum is 50 mm, if several layers of a prefabricated base are used, then 70 mm. For a wet screed, the additional length can vary from 10 to 100 mm - it all depends on the specific conditions.
Moreover, there are different technologies for screeds: you can use a concrete screed over a layer of large expanded clay, you can lay plywood on a concrete base. Different ways are good in different ways.
How to coordinate rooms by level.
When the apartment has the same floor covering, then the screed is made under the same level. But often, for example, laminate flooring is laid in the room, tiles in the corridor and bathroom, because of this, it is necessary to coordinate the premises in terms of level before laying the final floor covering.
It's simple: to determine the height of the screed in each room, you need to count all the layers of the future flooring and subtract them from the final level. Although everything is simple, but if this is not done at the preliminary stages of apartment renovation, then the floor with steps is provided to you.
Zero level markup methods
1.1. water level.
The most affordable and easiest way is to beat off the zero point of the room with a water level - a spirit level. Two glass tubes with water connected by a long hose allow you to measure not only the levels in one room, but throughout the entire dwelling.
Plus:
Ease of use.
Small tool price.
Minuses:
One person is not enough to measure.
Accuracy depends on the condition of the tool: the hose must not be kinked, air must not enter, etc.
1.2. Auxiliary level method.
At an arbitrary height, we draw a horizontal line and measure the distance to the floor after a certain distance. The more marks, the higher the measurement accuracy.
Pros:
Versatility: can be applied to any horizontal and vertical surfaces.
One person is enough.
Minuses:
Lots of measurement samples to achieve an accurate result.
If there are erroneous measurements, then measurement errors accumulate.
1.3. Laser level
To be more precise, the measurements do not use a laser level, but a laser level. The method is based on the principles of the laser level, that is, the line outlined by the laser beam in space is the desired level.
Pros:
The most accurate measurements.
One person is enough to measure.
Minuses:
The high price of the tool.
The possibility of measurements depends on the conditions in the apartment, problems may arise with strong illumination or with a lot of dust in the room.
Bottom line: all methods are good if you apply them when necessary. The result will be at a high level, especially if you arm yourself with a high-quality and serviceable tool. We do home repairs for ourselves, so the result, as a rule, is at a good level.
P.S. And for dessert, I suggest watching a video clip: Comparison of laser levels

The main task in preparing for leveling the floor with a dry or concrete screed is to reach the zero level over the entire area of the apartment. The floor, in the end, should be one parallel to the horizon, a perfectly flat surface.

What is zero level in construction

Put a mark at the highest point of the relief in the apartment.
We duplicate this mark strictly horizontally on all other walls in all rooms in the apartment. To do this, it is best to use special tools - building levels.
Then you need to connect all the points, and then you get a zero level, and you need to level on it when performing a floor screed.

Moreover, there are different technologies for leveling the subfloor in an apartment: it is possible, on top of a layer of large expanded clay, to apply a dry floor screed with expanded clay, you can lay plywood on a concrete base. Different ways are good in different ways.

How to coordinate rooms by level

When the apartment has the same floor covering, then the floor screed is made under one level. But often, for example, laminate flooring is laid in the room, tiles in the corridor and bathroom, because of this, it is necessary to coordinate the rooms in terms of level before laying the final floor covering.

It's simple: to determine the height of the screed in each room, you need to count all the layers of the future flooring and subtract them from the final level. Although everything is simple, but if this is not done at the preliminary stages of apartment renovation, then the floor with steps is provided to you.

Zero level markup methods

water level

The most affordable and easiest way is to beat off the zero point of the room with a water level - a spirit level. Two glass tubes with water connected by a long hose allow you to measure not only the levels in one room, but throughout the entire dwelling.

Ease of use.
Small tool price.

One person is not enough to measure.
Accuracy depends on the condition of the tool: the hose must not be kinked, air must not enter, etc.

Auxiliary level method

At an arbitrary height, we draw a horizontal line and measure the distance to the floor after a certain distance. The more marks, the higher the measurement accuracy.

Versatility: can be applied to any horizontal and vertical surfaces.
One person is enough.

Lots of measurement samples to achieve an accurate result.
If there are erroneous measurements, then measurement errors accumulate.

To be more precise, the measurements do not use a laser level, but a laser level. The method is based on the principles of the laser level, that is, the line outlined by the laser beam in space is the desired level.

The most accurate measurements.
One person is enough to measure.

The high price of the tool.
The possibility of measurements depends on the conditions in the apartment, problems may arise with strong illumination or with a lot of dust in the room.

Bottom line: all methods are good if you apply them when necessary. The result will be at a high level, especially if you arm yourself with a high-quality and serviceable tool. We do home repairs for ourselves, so the result, as a rule, is at a good level.

P.S. And for dessert, I suggest watching a video clip: Comparison of laser levels

Answer from OLGA KHALIMOVA[guru]
As you know, any ship has a waterline, which is clearly visible to everyone and its meaning is clear to everyone. There is something similar in every apartment - this is the zero level. Although the meaning of the zero level follows from the name, it is not visible and it is not clear how and where it comes from.
When preparing the base of the floor with a concrete or dry screed, the main goal is to reach the zero level over the entire area of \u200b\u200bthe apartment. Make the floor surface in the entire apartment at such an equal level that the finishing floor coverings are one flat surface parallel to the horizon line.
How to conduct a zero level
The zero level is carried out on the basis of two conditions:
the highest point in the relief is determined over the entire area of \u200b\u200bthe apartment
special tools are used - building levels
3-5 cm is added to the highest point of the floor relief and a zero level is drawn. The run-up of an additional segment of 3-5 cm depends on the type of screed used. For wet screeds, a run-up of 1 to 10 cm is possible - it all depends on the specific conditions. Screeds based on self-leveling mixtures give a thin layer of a few to tens of millimeters, and traditional concrete screeds start from 5 cm and thicker. There is a limitation for dry screed:
minimum thickness - 3 cm
maximum thickness - 5 cm when using one layer of dry backfill and one precast base, and 7 cm when using several layers of prefabricated base.
Variations of floor screed technologies are also possible. There are technologies where a concrete screed is applied over a layer of large expanded clay, and there is a well-known method of laying plywood on a concrete base - each method is good in individual performance.
How to coordinate rooms by level
It's great if everything is simple in the apartment - linoleum or laminate is everywhere. So the screed is made under one level. And if, say, there are tiles in the corridor and the bathroom, and parquet in the rooms? You will have to coordinate the premises in terms of level before laying the finish flooring.
The idea is simple: count all the layers of the future flooring, subtract them from the finish level and determine the height of the screed in each room. The truth is completely transparent, but it’s worth talking about it, since it is necessary to coordinate the premises according to the level at the very preliminary stages of repairing an apartment with your own hands. If this is not done, then you will have to use the well-known Russian ingenuity or put up with the resulting mini podium and the inscription "carefully step" :)
Zero level markup methods
Measuring with a water level
The most logical and familiar way is to measure the premises with a water level - a spirit level. Two communicating vessels filled with water and connected by a long hose allow you to measure not only the levels in one room, but throughout the entire apartment.
Advantages
The simplicity of the measurement method
Inexpensive measurement tool
Flaws
It takes two people to measure
Measurement accuracy depends on the condition of the liquid, in the event of air entering the liquid or kinking of the hoses, significant measurement errors appear
Auxiliary level method.
IN convenient location, a horizontal line is drawn at an arbitrary distance from the floor and the heights to the floor are measured after a certain distance. The number of marks increases the measurement accuracy. This method has already been described by us earlier.
Advantages
Versatility of the method: suitable for working with horizontal and vertical lines, and even for measuring inclined surfaces
No assistant needed
Flaws
A large number of measurements
Limited measurement accuracy, improved accuracy achieved a large number measurements. In the case of the appearance of erroneous measurements, the measurement error accumulates.
With a laser level
Strictly speaking, not a laser level is involved in the measurements, but a laser level. We'll talk more about this method here. The essence of the method follows from the principle of operation of a laser level: a line outlined in space is the desired level.

As you know, any ship has a waterline, which is clearly visible to everyone and its meaning is clear to everyone. There is something similar in every apartment - this is the zero level. Although the meaning of the zero level follows from the name, it is not visible and it is not clear how and where it comes from.

When preparing the base of the floor with or, the main goal is to reach the zero level over the entire area of \u200b\u200bthe apartment. Make the floor surface in the entire apartment at such an equal level that the finish is one flat surface parallel to the horizon line.

How to conduct a zero level

The zero level is carried out on the basis of two conditions:

the highest point in the relief is determined over the entire area of \u200b\u200bthe apartment
special tools are used

3-5 cm is added to the highest point of the floor relief and a zero level is drawn. The run-up of an additional segment of 3-5 cm depends on the type of screed used. For wet screeds, a run-up of 1 to 10 cm is possible - it all depends on the specific conditions. Screeds based on a self-leveling mixture give a thin layer of a few to tens of millimeters, and traditional concrete screeds start from 5 cm and thicker. There is a limitation for dry screed:

minimum thickness - 3 cm
maximum thickness - 5 cm when using one layer of dry backfill and one precast base, and 7 cm when using several layers of prefabricated base.

Variations of floor screed technologies are also possible. There are technologies where a concrete screed is applied over a layer of large expanded clay, and there is a well-known method of laying plywood on a concrete base - each method is good in individual performance.

How to coordinate rooms by level

It's great if everything is simple in the apartment - linoleum or laminate is everywhere. So the screed is made under one level. And if, say, there are tiles in the hallway and bathroom, but in the rooms? You will have to coordinate the premises in terms of level before laying the finish flooring.

The idea is simple: count all the layers of the future flooring, subtract them from the finish level and determine the height of the screed in each room. The truth is completely transparent, but it’s worth talking about it, since it is necessary to coordinate the premises by level precisely at the most preliminary stages. If this is not done, then you will have to use the well-known Russian ingenuity or put up with the resulting mini podium and the inscription "carefully step" :)

Zero level markup methods

Measuring with a water level

The most logical and familiar way is to measure the premises with a water level - a spirit level. Two communicating vessels filled with water and connected by a long hose allow you to measure not only the levels in one room, but throughout the entire apartment.

Advantages

The simplicity of the measurement method
Inexpensive measurement tool

Flaws

It takes two people to measure
Measurement accuracy depends on the condition of the liquid, in the event of air entering the liquid or kinking of the hoses, significant measurement errors appear

Auxiliary level method.

In a convenient place, at an arbitrary distance from the floor, a horizontal line is drawn and the heights to the floor are measured after a certain distance. The number of marks increases the measurement accuracy. This method by us

Advantages

Versatility of the method: suitable for working with horizontal and vertical lines, and even for measuring inclined surfaces
No assistant needed

Flaws

A large number of measurements
Limited measurement accuracy, increased accuracy is achieved by a large number of measurements. In the case of the appearance of erroneous measurements, the measurement error accumulates.

With a laser level

Strictly speaking, not a laser level is involved in the measurements, but a laser level. About this method The essence of the method follows from the principle of operation of a laser level: a line outlined in space is the desired level.

Advantages

The highest measurement accuracy
Possibility to measure without assistants

Flaws

The use of expensive tools
Measurements are difficult when the sun is strong or the room is very dusty.

Let's summarize. Any method is good in its own way, and if applied to the place, then a very worthy result is obtained. Moreover, when armed with a good, serviceable tool and a faithful assistant, it is impossible to do badly, because repairs are own apartment you do for yourself.