The procedure for troubleshooting the operation of a plastic door. Is it possible to open a plastic balcony door from the outside, locked from the inside of the house? How to open a plastic door on a balcony

Plastic door on the balcony n has a large number of advantages: it protects well from street noise, does not need additional insulation in winter, it does not need to be painted. This design is undemanding to care and functionally convenient, but sometimes it can cause trouble. Any product wears out over time and can break at the most inopportune moment. If the problems were not noticed in time, this is fraught with the fact that the door will stop opening or, on the contrary, it will be impossible to close it. What to do if jammed plastic door? Let's look at the causes of the problem, how to fix it and prevent it.

The first, most important condition that must be observed if the balcony door does not open is not to try to redouble your efforts. Excessive pressure on the handle or door leaf can damage the fittings or lead to deformation of the canvas, and then repair or replacement will cost a decent amount. Of course, there is little pleasant in such a situation, especially if you are outside. Trying to break the glass is ineffective, because the double-glazed windows in the doors are very strong. Glazing beads run from the side of the glass. They need to be carefully picked up with something sharp and carefully removed. After that, it will be easy to dismantle the double-glazed window from the frame. If the door jammed when you were inside the apartment, there are much fewer problems, but before proceeding with any drastic actions, you need to find out the cause of the breakdown.

Stuck handle

If you ignore the rules for caring for the fittings of a plastic balcony door, then this problem will definitely appear. The mechanism needs regular lubrication, otherwise it stops opening. To restore mobility to a jammed handle, it is necessary to process the elements of the handle mechanism and locks. Any lubricant is suitable for this, including automotive.

If the handle could not withstand intensive use and broke, it will need to be replaced. Accessories for plastic doors and windows can be purchased at any specialized store. Remove the handle when it is in the "open" position. Fasteners are located under the decorative plate. To get close to them, it must be slightly pulled towards you and turned to a horizontal position. Then it remains to unscrew the screws, remove the broken fittings and install a new handle.

Skewed or deformed door leaf

jam the door can even if the canvas is skewed or deformed. As a rule, such a problem does not appear immediately, and an attentive owner will definitely notice the first signs: a deformed seal, a creaking handle, the need to make more efforts to close the door. Skew often occurs when the hinges cannot cope with the load from a heavy sash.

Adjustment should be made immediately. First you need to find out in which direction the displacement occurred. The closed door around the perimeter is outlined with a pencil, then the sash is opened and the direction of displacement is determined. To eliminate the vertical skew of the structure, tighten the hex screw, which is located at the top or bottom of the hinge. Turning clockwise lowers the sash, reverse side- raises. To align the horizontal plane, it is necessary to slightly remove the plugs from the hinges, tighten the hinge screw and use the hex key to rotate the screw. These actions help to solve the problem with the skewed door leaf. If deformation has occurred, it is unlikely that it will be possible to fix the problem on your own, you will have to call specialists.

Locked handle when turning

This happens if you sharply turn the handle and at the same time move the sash. opening the mechanism freezes, the handle is blocked, and the door leaf remains with a single point of support in the lower corner. The procedure for troubleshooting this problem will depend on the brand of hardware that is indicated on the mounting plate of the handle. If the product is labeled Roto, GU or Winkhaus, you first need to find the metal tongue of the mechanism, which is located at the end of the frame, just below the handle itself. It must be deployed vertically, while turning the handle to the "open" position. Press the door firmly against the frame and close with the handle.

For fittings marked AUBI, the tongue design is replaced by a metal plate and a spring. The repair process goes like this:

the door leaf is aligned to the correct vertical position;
the plate is pressed tightly against the seal;
cover the sash and press it against the frame;
turn the handle to the "closed" position.

After these events, the door will function as usual.

Door stuck to frame

Ventilation in severe frost can cause condensation to appear on the seal due to the contrast between indoor and outdoor temperatures. After the door is closed, the liquid freezes and blocks the sash. If there is no urgent need to go out onto the balcony, you can wait for the natural thawing of ice. Or you will have to use a hairdryer and blow hot air around the entire perimeter of the door leaf. In order to slightly improve air access, the door during the heating process must be slightly pulled in the direction in which it opens. When the sash was opened, the seal should be thoroughly wiped from moisture and treated with silicone grease.

A foreign object has entered the lock mechanism

If the lock mechanism is blocked by a foreign object, the handle will not move to its full extent. You can clean the lock as follows:

remove handle from base decorative overlay and unscrew the screws;
remove the handle;
vacuum the hole well, changing the position of the handle several times;
spray into the hole from a can of WD-40, twist the handle.

If nothing helps

If the balcony plastic door does not open, what else can you do when all the methods have already been tried? If it is impossible to understand why the door has become seize You will most likely need to call in the experts. If the door does not want to open after all the events, it will have to be removed from the hinges in order to gain access to the locking mechanism and figure out the cause of the breakdown. If you have no experience in such work, let the master do it.

Prevention measures

It is much easier to prevent a malfunction than to get into a difficult situation and urgently try to fix it. Preventive measures do not take much time:

All moving structural elements must be lubricated twice a year.
Clean the accessories from dust and dirt so that foreign objects do not get into the mechanism.
Turn the door handle smoothly, without jerking.
Do not open the sash until the handle has been fully rotated to the desired position.
Do not hang bags on the doorknob, do not lean on.
Check the position of the door from time to time and make adjustments if necessary.

Subject to the rules of operation and appropriate care, the plastic balcony door will serve without causing problems.

Hide

How to open a plastic window, especially from the side of the street , not only a thief can think: sometimes the owners of the apartment also have such a problem. So, the front door can jam. This can happen for various reasons: for example, you went out onto the landing, leaving the keys in the apartment, and the door was slammed or locked from the inside. Small child. Homeowners often lose their keys front door then the only way to get home is through the window. Also knowing how to open a plastic window , may be required if it is jammed.

In fact, products are rarely equipped with additional protection against burglary, and it is easy to open them with a screwdriver or any flat metal object, such as a ruler.

Opening plastic windows: ways and methods

Let's say the window is closed, you're outside, and all you have is a flathead screwdriver. First you need to find where the latch is located. You will need to gently squeeze the window sash by pressing on the fittings. If you manage to do everything right, the sash will open slightly, you can stick your hand in and turn the handle, opening the window completely.

How to open a plastic window from the street with a ruler?

If there is no screwdriver at hand, but a metal ruler is found, you can use the following scheme: the ruler is placed between the window frame and . Then you need to find the latch, try to hook it and pull it down. Be careful not to damage the window plastic. This material is quite flexible and will easily allow you to squeeze the ruler where you want it. If you do everything right, the window will open.

However, it should be borne in mind that they have a variety of designs, and you need to act in accordance with which design you have installed. The above methods illustrate how to open a plastic window with standard handles. If you have a different construct in front of you, these methods may not work.

How to open a plastic window without a handle?

Self-opening of such a structure from the side of the street is extremely difficult. You can try to use any narrow object if the window is not locked. This method will help protect the structure from damage, and it will continue to function. As a result of the opening, it may be damaged. Almost always, mechanically applied scratches remain on it, less often chips.

Another way to open a plastic window from the outside is to drill. It will harm the frame, as it will appear through hole, through which it will be possible to insert a narrow object, for example, a wire or a handle, and open the sashes with it.

How to open a double glazing , without harming him - an important issue for the owner of the window. Not everyone will want to change or repair after they need to get into the room. These methods are the safest for the design and allow you to save its functionality.

Features of outward opening windows

How to open from outside , if the sash opens in the same direction? This question is quite interesting, because before trying to open such a window, you need to study its features.

Typically, such designs have double-sided lock-type handles, which allows them to open in the other direction. There may also be additional fittings that open the sash, for example, in the ventilation mode. If there is such a function, this is good: you can try to switch the window to this position with the help of a ruler, squeeze your hand inside and open it.

Quite often this method does not work with this type of windows. You can try to pry them off with a crowbar or chisel, but as a result, the window will be broken and it will need to be repaired, since the locking mechanism will be disabled.

How to open a window without a handle?

If you are outside, you can try to open the double-glazed window with a screwdriver or a ruler in the manner described above. But it happens that such a problem catches the owner indoors. There is no handle at the window, it is jammed, and it is impossible to open the sash. In this case, you still need to purchase a pen or use pliers instead.

If you still can’t perform the action, the reason should be looked for in an element called scissors. Sometimes it comes out of the grooves and prevents the window sash from moving in the right direction.

Before opening a double glazing , you will need to find a tool to remove the sash from the frame. It is more convenient to remove the loops located at the top of the structure. When they are unscrewed, you will see a metal lining; remove it, remove the hinge pin, lift the bottom hinge and find the slots of the scissors. After the element falls into place, the window should work.

Tip: before you disassemble the window, try to get to the scissors from above. Sometimes the slopes do not interfere with this.

How to open a plastic balcony door from the outside?

A more common problem is a closed balcony door. For example, you went out to smoke, and they locked you on the balcony and they don’t hear you. There is a way out of the situation: if there is any tool on the balcony, you can try to open the door with a screwdriver. This is done according to the same principle as in the case of a plastic window.

Another way: unscrew, lift the door and open it from the other side. Or stick your hand into the hole and turn the handle to the desired position. But this may not always help, since many doors are equipped with additional protection. If you have such a door, then you will have to use the help of a door repair specialist.

Conclusion. Opening a plastic window from the outside is not as easy as it might seem. Without knowledge of the design, the presence of at least some tool at hand and a little experience, it may not be possible to open a window or a plastic door without damaging the structure. If you do not want to risk, call a window repairman: he will help solve the problem.

Ways to open a window from the outside

Many people believe that PVC windows protect housing from penetration more reliably than old Soviet windows. However, in reality, things are exactly the opposite.

The fact is that sashes made of plastic are much more flexible and soft than wooden ones, as a result of which they are easily bent. In a normal situation, this, of course, is a reason for frustration, but not in ours, when you need to get into a locked house.

When deciding how to open a plastic window from the outside, it is worth noting that in order not to harm the object, it is important to use a special tool.

method number 1

How to open a plastic window from the street. Armed with a thin metal plate or iron ruler, this element must be carefully placed between the frame and the double-glazed window.

Your next step is to get to the plastic window latch. Managed? Then we hook it with a tool and slowly pull it down.

There is absolutely no difficulty here, because plastic is a rather flexible material that cannot withstand the pressure of metal. The only negative of this method is the possible appearance of minor scratches, and even dents.

As a result of these actions, the cylinder of the locking mechanism should pop out of the hook;
if constipation is located in several parts of the valves, which most often happens, the procedure must be repeated by inserting a screwdriver in front of each of them. The moment the trunnion pops out of the hook is accompanied by a loud click.

Hacking scheme for standard fittings

This method of opening is quite simple, and, most importantly, after such a break-in, the fittings remain intact. The only thing is, if you do the work sloppily, you can scratch the plastic.

method number 2

How to open a plastic window from the outside with a screwdriver and without damage. Determine where the latch is. In that place, with this tool, try to press the window sash.

A more complicated option is when there are several trunnions in the opening mechanism. In this case, it is necessary to proceed in stages. Opposite each of the trunnions, you need to tear off the sash, pushing the trunnion over the bar, and proceed to the next one only after the previous trunnion is fixed on the other side of the bar.

It will be possible to open it by clicking on the fittings. Further, if everything is done correctly, the sash will open slightly. The next and last step is to turn the lock knob.

It should be noted that all these methods are effective only if the window is equipped with standard fittings. But if the attackers are professionals, then windows with anti-burglary fittings Roko and Mako can also break.

Anti-burglary fittings

method number 3

Is it possible to open a plastic window from the outside by drilling. It turns out that it is possible, but in most cases only burglars resort to this method. If in the previous methods the damage to the window is minor scratches, then in this case everything is bigger.

So, by drilling a hole with a pen or the same screwdriver, a window is opened. Of course, this way you will still get into the house, but your window construction will be damaged.

Jamming of a metal-plastic structure, which most often leads to a balcony, is enough common problem. It usually happens at the most inopportune moment. The breakdown itself is quite unpleasant, since it is usually not clear what to do in such a situation, how to fix it. If the door does not open, most likely it is jammed. In this case, you have to open the door without a key, which can be done in various ways.

Appearance one of the traditional plastic structures leading to the balcony

Sometimes it happens that the door jams at the moment when you went out onto the balcony in a light bathrobe. It will be useful to know in advance what to do if the structure is closed. Allocate various ways opening without a key, especially since there is usually no handle on the outside of the balcony door. This complicates the opening problem, but suitable methods for solving the problem can be identified.

Causes of door jamming

Attention! One of the most common causes of door jamming is improper operation by the owners. Many try to slam the door, pulling it towards themselves and pulling their hand out from under the structure at the very last moment. Often, all this leads to jamming due to the operation of the latch mechanism. In addition, this leads to rapid wear of the blade.

Improper operation of the door leaf is the main problem of breakdowns and failure. Also, jamming can be caused by sharp blows or slamming. This leads to a violation of the functionality of the structure. It is also worth highlighting the following reasons that the door does not open:

Broken lock on a plastic door. It can break when worn or objects get inside.
Skewed plastic construction due to weight or improper installation.
Failure of fittings, including the door handle.
Freezing door in winter time. This leads to the accumulation of condensate, which negatively affects the functioning of the web.
Involuntary blocking of the lock mechanism.

Of course, all these reasons are not critical. Everyone can deal with them. However important point It becomes a clarification of the cause, because only after that it is possible to eliminate the problem. If it is fatal, it is not recommended to eliminate it yourself. This may exacerbate the problem.

Balcony door jammed when a person was outside

What to do in non-standard situations?

Sometimes, especially during severe frosts, a plastic door can freeze to door frame. This can be observed when the structure is open for ventilation or if condensation accumulates on the seal. This leads to freezing it and the inability to open it. Initially, it is worth considering whether it is really necessary to urgently open the door. If so, don't try to break down the door. It won't lead to anything good.

Initially, you can try to warm the door. To do this, use a hair dryer. With mild freezing, 5-10 minutes of intensive heating will be enough. After that, wipe the box, and wipe the seal with a lint-free dry cloth. From above it is lubricated with silicone grease, excluding further freezing.

Appearance of a frozen metal-plastic door

Using a screwdriver as the main tool

You can try to open the lock mechanism with a thin screwdriver, a card or a metal blade. The principle is quite complicated and cannot always be carried out after the door has jammed. However, if any element of the lock often sticks, it is recommended to have necessary tools at hand.

The algorithm is based on picking up a glazing bead with the selected element. It is usually fixed in the double-glazed door. At the same time, try to act carefully so as not to scratch the door leaf. To do this, the glazing bead is picked up in the middle from the long side, after which it is carefully disconnected with both hands, moving towards the edges. Similar work is done on the other side of the element, as well as from below and above.

After the retaining glazing bead is removed, the double-glazed window should be removed. To do this, gently pull the upper edge of the double-glazed window towards you. Remember that a triple-glazed window weighs quite a lot, on average about 30 kg per square meter. Now you can reach the door handle to open the lock of the metal-plastic door from the inside. If not, you should try to get into the opening.

This method is also suitable when there is a latch instead of a lock. Remove the front panel and insert a screwdriver. With its help, they feel for the latch and move it.

Also, the method is perfect in cases where the handle has failed. To do this, a suitable object is inserted between the frame and the door. It can be a card or cardboard. With its help, they push the tongue to open the door.

Algorithm for opening a metal-plastic structure using a thin plate

What to do if the key is broken?

If the door leading to the balcony does not open because the key is broken, solving such a problem is much more difficult. You will have to use pliers or other improvised means to remove the key chip. However, this can be done only in cases where it sticks out. If not, the problem is somewhat more difficult to solve.

The main tool for solving the problem is the jigsaw blade. It should be thin enough to fit through the keyhole. The blade is pushed from the bottom side with the teeth up. After that, it is turned so that the key is hooked. This will help you get it out of the keyhole. After you got rid of the key fragment, you can use any of the above methods. At the same time, if you have an additional key, the problem is easily solved. You can safely use it to open the door.

If it was not possible to extract the chip in this way, you will have to solve the problem in a different way. To do this, unwind the lock using improvised methods. This will allow you to get the larva. However, in any case, it will be quite difficult to open the door, you may even need to call the master.

Jamming the door leading to the balcony, which will have to be opened without a key

Other methods of opening the door to the balcony

You can open the door leading to the balcony in other ways. They will be especially effective if the handle or lock is broken. The first thing to do is to get to the door, or rather to its inner side. To do this, gently squeeze the double-glazed window out of the door leaf. Usually it is fastened with glazing beads, which are previously removed. Now you can easily get to the broken handle.

The second method is considered no less effective. It is based on reducing the strength of the vestibule. This is done using an ordinary hex wrench. They unscrew the screw that holds the hinges in a certain closed position. It should be understood that when closed door this is not always possible.

Attention! If all else fails, you can use radical methods. These include the complete dismantling of the door or fittings. It should be understood that this will lead to the need complete replacement door structure.

Metal-plastic door that leads to the balcony

Now you know how to open a PVC door on your own if the lock is broken or the handle is out of order. It is worth choosing the preferred way to open the door to the balcony. There is no need to worry about the fact that the key to the door is missing. It will be possible to open without it at all. If your door leading to the balcony often jams, functions with difficulty, or has problems with the mechanism, you should familiarize yourself with possible ways to open the structure.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your own ...

New Articles

New comments

S.A.

Grade

Svetlana

Grade

Sergey

Grade

Sergey

Grade

Alexei

Grade

Latest reviews

adminadmin

Metal-plastic windows have won a strong place in the market building materials: they are increasingly preferred. Positive traits: protection from heat, nice design, excellent sound insulation please many owners. However, there are also troubles: sensitive mechanisms fail, a naughty lock can close at the most inopportune moment. The cause of the failure can be one of many factors. If your plastic balcony door does not open, what should you do? This will be discussed in our article.

Most manufacturers simplify the plastic door lock and put a three-position mechanism, where in the upward position the door is placed for ventilation, in the horizontal position it opens, and in the lower position it remains firmly closed.

The deterioration of the mechanism conceived leads to a violation of its work. Loose parts of the castle may fall out of their grooves, so a situation may happen when the owner of the apartment is locked on his loggia or balcony.
Another option is problems with turning the handle: jamming, the inability to open the door or even turn the lock. The reason for this behavior can be rust, complete deterioration of the lock, lack of lubrication, cold.
Another common cause is plastic wear. Most of the moving parts are molded from PVC materials, which tend to break, crack, and deform frequently. Excessive force, “slamming”, insufficient care can aggravate the condition of the doorway.
The weak point of the design is the curtains. The plastic door to the balcony does not open - it is jammed due to rust, plaque, debris or dirt on the curtains or hinges. It is even worse if only the lower curtain, which is responsible for the “ventilation” installation, was damaged. In this case, the repair will take a lot of time and effort.

So, if the balcony door does not open, then the problem lies in one of the important nodes: curtains, a lock, a plastic frame. Determining where the breakdown is quite simple.

The lock is broken or jammed if it is impossible to turn the handle or an uncharacteristic rattle, creak is heard when turning, or the handle is hard to turn.
The problem is in the curtains, if it is not possible to fully open the opening directly when opening or placing the plane “on position”.
The problem of plastic deterioration with visible physical damage: cracks or missing fragments, curvature of the door plane.

Repair of these nodes at home is almost impossible. Retailers have sets of locks, curtains, and so on. for metal-plastic, but for their installation at least two people are needed (the weight of a double-glazed window reaches 70-80 kg), special tools, work experience. TO plain sight repair can include the replacement of the contents of the castle. The insides of the mechanism are hidden under a small plate at the end, which is fastened with two self-tapping screws. Replacement is carried out on the spot, without removing the door plane. Other types of repairs involve the dismantling of the opening and the replacement of the main components in the workshop.

Ways to solve the problem

If trouble caught you inside the house - it does not matter. An easy way to solve the problem is to call a locksmith at home. Only a master with extensive experience will be able to determine the cause of the breakdown, quickly eliminate it and restore its former functionality. Metal-plastic windows have a very limited scope, they are used to create high temperatures and special machines.

It is a completely different matter if the door jammed when you were on the loggia or balcony. This can happen due to several reasons: if you pushed the euro door hard when going outside, or because of drafts and strong gusts of wind. If this happens, you should not panic, especially if you live on the upper floors. Getting out of this situation is very easy.

If you have the keys with you - call a friend or neighbor, let him help you out.
You can try to get out through the neighboring balcony if the residents are aware of your trouble. (only with insurance).
You can independently dismantle the double-glazed window and climb back into the apartment through the window opening.

The latter option is most preferable for most people who find themselves in such a situation. How to open a plastic balcony door with an ordinary coin from the inside? Very simple. To dismantle the double-glazed window, it is necessary to pry off the plastic glazing bead along the glass contour with a thin metal or wooden object. Having removed it, you need to slightly press on the plane and tilt the glass to the other side. If possible, do not break the double-glazed window. This is a rather expensive part of the door, its replacement costs a lot of money.

Also, do not knock out the double-glazed window from the outside. A thick layer of glass will not succumb even to a physically strong man. You can aggravate your situation if you hit the door with a heavy object.

One way to unlock the door:

Instructions for removing a double-glazed window from a plastic structure:

Caring for a metal-plastic door

Recognizing that something is wrong with your metal-plastic door is easy enough. Main features:

extraneous noise, rattle during opening;
depressurization (water leakage, draft);
violation of sound insulation;
sticking of the handle;
cracks, chips on plastic.

In general, some problems of metal-plastic cannot be solved. This is especially true of the plastic frame, which can quickly deteriorate, especially in an unfavorable northern climate. Protection of locks and curtains can be provided periodically (once a year or two) by lubricating them with oil of medium density. Periodic checks, lubrication of the main components, replacement of rubber bands and gaskets will extend the service life and protect you from trouble with sudden jamming of the door.

Being closed from the side of the street, when you have no idea how to open the plastic balcony door from the outside, is unpleasant and even dangerous if the balcony is not insulated, and the weather does not favor walking in home clothes. Owners are not immune from such incidents. plastic windows and old-style doors not equipped with a handle for outside use.

The absence of additional fittings is a feature of the simplest models of windows and balcony pvc doors. What to do in such cases and what are the effective ways get home without damaging the design of windows and doors? There are options, and everyone who does not have a balcony door equipped with a double-sided handle should take note of them.

Why the door jams: the main reasons

To begin with, let's figure out why the balcony door of the balcony or loggia does not open, which had served properly before. There may be several reasons. One of them is careless handling. Sudden movements in relation to the plastic balcony door can lead to the opposite effect - the latch mechanism will not work properly and the exit will be blocked.

Malfunctions of the components can also affect the malfunction of the door. So, for example, the reason is:

in malfunctions of the lock mechanism during the opening of the canvas in the “ventilation” mode;
in the breakage of the handle;
in the skew of the structure;
in the freezing of the system due to the condensate formed between the box and the seal.

The listed faults are not critical. As soon as it is possible to determine the cause of the blade jamming, it is worth trying in a delicate way to return it to the “open” position. It is important at such moments to remain patient, not panicking, trying to break the product. A broken balcony door will add to the hassle and cost of repairs and replacements.

Options for "liberation" from a balcony blocked from the inside

If the plastic door to the balcony is jammed, where there is at least a minimal set of tools (it does not hurt to keep it there just in case), then the situation can be considered controlled. A simple screwdriver is enough to gently press the latch of the lock, slightly pressing the fittings. If everything is done correctly, the sash of the canvas will open a little and it will turn out to put your hand in for the final opening.

Instead of a screwdriver, a spatula, hacksaw or knife is suitable for these purposes. The main thing is to try using a sharp object to lift the glazing bead, which is attached to the door with a double-glazed window on each side, disconnecting it from the central part to the edges. The same manipulations must be done from above and below, and then try to remove the glazing bead by pulling it in your direction, thus freeing the double-glazed window.

An important point: the weight of a double-glazed window in the design of a balcony door can exceed 30 kg, so you should be extremely careful holding it after all the manipulations.

After the double-glazed window is removed, unimpeded access to door handle from within. Even if the lock does not work and the door does not open, you can get inside through the window opening, continuing to repair the door in a warm room.

Attention! Don't try to break the glass pane. The outer glass is quite thick and is likely to withstand the onslaught. Only a heavy metal object can cope with glass with a thickness of 4 mm or more. Glass shards can cause injury, and replacing double-glazed windows will require investment.

Ruler for unlocking the balcony door - how to use?

If there was no set of tools, a knife or a hacksaw when the balcony door was jammed on the loggia or balcony, but there is an opportunity to use a metal ruler, you should try to get out with it.

Just as in the case of the sharp objects listed above, you can pick up and pull down the latch of the canvas with a ruler. Actions must be careful, without haste, with respect for the material of construction. The plastic is flexible enough that the ruler will be able to reach the target.

If it didn’t work to open the latch with a ruler, for example, when the cause of the jamming is not in the lock, you should try an effective and delicate way to unscrew the door hinges. It will be easier to cope with the task if you know their device. Usually a balcony door hinge is a metal tab with fasteners, a frame part and a spacer.

By adjusting the composite hinges, even when the door is stuck, you can move the canvas a little in the right direction.

Important: most often the door leaf screws are masked with decorative overlays.

Jammed door: what to do indoors

It is not so unpleasant to face the fact of a jammed door inside the room, having at hand everything you need to solve the problem on your own, as well as the ability to call a master who knows what to do if the door to the balcony is jammed and how to set it up for normal operation without replacement.

Often the balcony door jams from the inside in the ventilation mode. To solve the problem, it may be enough to set the handle in a horizontal position, and then try to feel the metal tongue at the end of the blade in the lock area, setting it to vertical position.

Alternatively, it is also worth trying to press the spring-loaded plate responsible for blocking the lock, or else align the canvas in a vertical position, attaching it to the box while turning the handle down to the end. These actions help open the balcony door from the inside without drastic interference with the operation of the system.

In conclusion, we note that no one is immune from the troubles associated with the operation of balcony door systems, and it is not so important whether the structures are equipped with an additional handle on the outside or not. The main thing is to be prepared for any force majeure situations, having a simple set of tools on the balcony or loggia that allows you to open the jammed door. Prevention of breakage will be regular care of the door, with lubrication and adjustment of the hinges, timely repair of fittings.