Thermal electric gun 60 kW. Is there any savings when using an industrial heat gun

Logistics data

Weight, kg: 20,00
Dimensions, mm: 370 x 780 x 520

The electric heater KEVP is designed for drying rooms during finishing works in construction, as well as for heating industrial premises.

1. Purpose of the product
Electric heater heat gun KEVP-60 (SFO-60)(hereinafter heater) is intended for drying premises during finishing work in construction, as well as for heating industrial premises.

2. Specifications KEVP-60 (SFO-60)

3. Completeness
Electric heater 1pc.
Passport 1pc.

4. Device and principle of operation
The heater is a housing in the form of a pipe, inside which tubular electric heaters are placed ( heating element) and a fan. conclusions heating element ov are connected in groups and brought to the terminal block of the control panel (PU). The wires of the fan electric motor are also brought out there. A thermostat may be present in the design of the control panel, see 3.
Heater housing KEVP-60 (SFO-60) mounted on a stand made of pipes and fixed with two screws. The angle of the case can be adjusted and is fixed in the stand with a special screw.
During operation, the air flow from the fan, passing through the heater KEVP-60 (SFO-60), goes around heating element and heat up to a certain temperature.

5. Placement and installation
The heater is installed in rooms that do not contain harmful acid vapors, explosive gases, conductive dust, etc. The air temperature in the room is from +1˚С to +35˚С, air humidity should not exceed 65% at 20˚С.
To assemble the heater KEVP-60 (SFO-60) it is necessary to remove the body and stand from the package, open the cover of the control panel on the heater body KEVP-60 (SFO-60) and remove the two fixing screws. Install heater housing KEVP-60 (SFO-60) on the stand and fasten with screws.
Before installing the heater KEVP-60 (SFO-60) it should be inspected to identify and repair damage, dents and other defects formed during transportation. Particular attention should be paid to the integrity of tubular electric heaters.
Connecting a heater KEVP-60 (SFO-60) to the power supply network is made with a cable with copper conductors with a cross section of at least 4 mm 2 - for KEVP 25 not less than 16 mm 2 - for KEVP-40, not less than 25 mm 2-for KEVP-60. Grounding is carried out specially residential, with a cross section of at least phase, the use of a neutral and working conductor for these purposes is not allowed.

6. Security measures
All electrical work must be carried out in accordance with the electrical rules and regulations for the operation of equipment operating under voltage up to 1000 V. During installation and during operation of the heater KEVP-60 (SFO-60) the following requirements must be met:
- heater housing KEVP-60 (SFO-60), which in the event of a breakdown may be energized, must be reliably grounded;
- all inspection and repair work must be carried out with the voltage removed;
- operation of the heater is not allowed KEVP-60 (SFO-60) with open lids.
Duty personnel serving the heater KEVP-60 (SFO-60) must:
- to know the device of the heater KEVP-60 (SFO-60):
- know the electrical circuit of the heater and follow the safety rules:
- be able to identify malfunctions in the operation of the electric heater:
- remember that turning on the electric heater when the fan is off is strictly prohibited.
Operation of a faulty electric heater is strictly prohibited.

7. How to work
Before turning on the heater KEVP-60 (SFO-60) it is necessary to make sure that the protective earth is present and in good condition. The heater is turned on by an automatic switch-off located in the control panel, and the signal lamp lights up.
When using the heater, the following requirements must be observed:
- operation of the air heater with the fan off is not allowed;
- at least once every four months, check the insulation resistance heating element ov relative to the heater housing; this check should be carried out before each switching on after a long period of inactivity (more than 15 days). When the resistance drops below 0.5 mΩ, the heating elements should be dried by connecting them to a low voltage (36 ... 42V), while turning off the fan electric heater.
- at least once every three months it is necessary to check the condition of the protective grounding;

8. Rules for storage and transportation
Electric heater KEVP-60 (SFO-60) should be stored indoors under conditions that exclude the possibility sun rays, moisture, sharp fluctuations in temperature. The ambient air temperature during storage of the air heater must be within the range from +5˚ С to +40˚ С. Relative air humidity at +20˚ С should be no more than 65%. Transportation of the electric heater in the original packaging is allowed to be carried out by any mode of transport at any distance. Transportation conditions in terms of the impact of climatic factors - according to the group of storage conditions 4 (Zh2) GOST 15150-69; transportation conditions in terms of the impact of mechanical factors - according to the group of transportation conditions L GOST 23216-78.

9. Manufacturer's warranties
The manufacturer guarantees the normal operation of the heater KEVP-60 (SFO-60) subject to the user's terms of use.
The warranty period of operation is set within one year from the date of commissioning of the heater KEVP-60 (SFO-60) in operation, but not more than 1.5 years from the date of manufacture.

For heating large rooms, it is not always rational to use conventional gas or electric heating. With the help of standard batteries and convectors, it is difficult to warm up a large warehouse or workshop. It is necessary to constantly spend energy resources to maintain the desired temperature. It is not always necessary to supply heat around the clock, as there will be no people there for several hours or days.

Therefore, it is necessary to use a heat source that can set the required temperature in a short time and maintain it. The industrial electric heat gun SFO-60, which can be bought from various suppliers in our country, has become a popular solution for warehouses and garages. It is also used at the construction site, to start machinery and generators. small size and several operating modes allow you to use the unit as efficiently as possible and at the same time, in total, spend few resources.

Are there any savings when using an industrial heat gun?

Despite the fact that the rated power of the equipment is quite large and during operation it consumes a lot of energy, the use of an industrial electric heat gun will be more profitable than stationary gas or other heating. Its principle of operation is based on rapid heating, that is, the unit will work for a certain time, after which it automatically turns off.

In addition, the price of an industrial electric heat gun SFO-60 will be cheaper than installing a boiler with all communications. If you choose the right model, the room will heat up in a short time, after which the unit will automatically turn off and on, maintaining the desired temperature. After the end of the working shift, the unit can be turned off so as not to waste electricity.

Sale of industrial heat gun electric

There are different models in terms of power and size, they are portable and stationary. Since it is necessary to quickly heat the air, a large peak load is used, so the unit needs 380 V to operate, that is, the connection must be three-phase. Today, the sale of an industrial electric heat gun is actively conducted through the online store of our company.

A three-phase connection often refers to industrial models; for domestic use in stores, you can find 3-5 kW guns. With their help, you can warm up a small shed or garage, use heat gun on suburban area if necessary.

Specifications SFO-60:

Power consumption - 60 kW
Network parameters - 380 V / 50 Hz
Rated productivity - 5680 cubic meters / hour
Number of heating elements - 15 pcs
Operating mode - 12/36/60 kW
Overall dimensions WxHxD - 900*765*550 mm
Weight - 70 kg
Producer - Ural-Mikma-Term